STX Signal Transmitter Installation and Operation ... - Kistler-Morse
STX Signal Transmitter Installation and Operation ... - Kistler-Morse
STX Signal Transmitter Installation and Operation ... - Kistler-Morse
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Chapter 6. MVS-<strong>STX</strong> Inputs <strong>and</strong> Outputs Menu<br />
16. Press the F1 Key to select Net or F3<br />
Key to select Gross. The display acknowledges<br />
the selection <strong>and</strong> returns to:<br />
SET:<br />
Net/Grs<br />
17. Press the F3 Key to select Fsafe. The<br />
display shows:<br />
FAIL-SAFE MODE?<br />
Lo Hi *NC<br />
F1 F2 F3<br />
(Asterisk indicates the current selection.)<br />
18. Press the F1, F2, or F3 Key to select the<br />
desired fail-safe condition. The display<br />
acknowledges the selection <strong>and</strong><br />
returns to:<br />
SET:<br />
Net/Grs<br />
19. Press the Esc Key to scroll up the menu<br />
tree or press the Auto/Man Key to return<br />
to channel monitoring.<br />
Current Output Report<br />
The MVS allows you to view the address <strong>and</strong><br />
channel number of the current outputs of any<br />
channel in the system. Follow this procedure<br />
to access the report for the current outputs<br />
on the Current Output PCB; the procedure to<br />
access the report for the <strong>STX</strong> PCB’s current<br />
output is similar.<br />
1. If in Auto Mode (Auto LED illuminated),<br />
press the Auto/Man Key to put the MVS<br />
in Manual Mode. The Auto LED turns off.<br />
2. Use the Arrow Keys to scroll to the<br />
desired channel.<br />
3. Press the Menu Key to display the Main<br />
Menu. The display shows:<br />
MAIN MENU<br />
F1 F2 F3<br />
4. Press the F2 Key to access the I/O<br />
Menu. The display shows:<br />
INPUT/OUTPUT MENU<br />
SetPt Iout Serl<br />
F1 F2 F3<br />
5. Press the F2 Key to access the Iout<br />
Menu. The display shows:<br />
CHOOSE 4/20 TYPE<br />
MVS<br />
FSafe<br />
F1 F2 F3<br />
FSafe<br />
F1 F2 F3<br />
Disp I/O Cal<br />
<strong>STX</strong><br />
6. Press the F1 Key to select MVS. The<br />
display shows:<br />
CURRENT OUTPUT<br />
Set Mode Rprt<br />
F1 F2 F3<br />
7. Press the F3 Key to access the<br />
Rprt Menu. The display flashes a<br />
message stating:<br />
CURRENT OUTPUT<br />
REPORT ON VES:X<br />
F1 F2 F3<br />
The channel number you previously<br />
scrolled to will be displayed after VES.<br />
The display then changes to:<br />
1ST Output Chan<br />
Addr XX<br />
Chan# YY<br />
F1 F2 F3<br />
Use the Arrow Keys to cycle between<br />
the current outputs on the Current<br />
Output PCB.<br />
8. Press the Esc Key to return to:<br />
CURRENT OUTPUT<br />
Set Mode Rprt<br />
F1 F2 F3<br />
9. Press the Esc Key to scroll up the menu<br />
tree or press the Auto/Man Key to return<br />
to channel monitoring.<br />
Serl (serial data)<br />
The Serl Menu sets up serial communications<br />
between the MVS or the <strong>STX</strong> PCB <strong>and</strong><br />
external equipment, such as:<br />
• a PLC with a BASIC Module or a similar<br />
communication device<br />
• a K-M ROPE system<br />
The Serl Menu also sets up communications<br />
between the MVS <strong>and</strong> other signal<br />
processors, such as a st<strong>and</strong>-alone <strong>STX</strong>.<br />
Serl has two submenus: MVS <strong>and</strong> <strong>STX</strong>. The<br />
MVS submenu sets up serial communications<br />
between the MVS <strong>and</strong> external equipment;<br />
serial communications can include<br />
information relating to all MVS channels,<br />
including the <strong>STX</strong> channel. The <strong>STX</strong> submenu<br />
sets up serial communications between<br />
the <strong>STX</strong> PCB, which has its own COM<br />
port, <strong>and</strong> external equipment; serial communications<br />
include information relating only to<br />
the one <strong>STX</strong> channel on the <strong>STX</strong> PCB.<br />
F1 F2 F3<br />
6-10