M-Maxâ„¢ Series Adjustable Frequency Drive - Eaton Corporation

More documents

Recommendations

Info

Parameters Quick Start Parameter Guide The following table shows the preset application parameters of parameter P1.2. in the factory setting. With P1.1 = 1 you are guided through the drive parameters in steps (Quickstart Wizard) after the power supply is switched on and after the factory settings are activated. Predefined Application Parameters from Parameter P1.2 Parameter (PNU) P1.1 1 = Only quick configuration parameters Basic (Standard Drive) Pump Drive Fan Drive High Load Designation Notes � 230V = MMX11_, MMX12_, MMX32_. 400V = MMX34_, 575V = MMX35_. 1 = Only quick configuration parameters 1 = Only quick configuration parameters 1 = Only quick configuration parameters 64 M-Max Series Adjustable Frequency Drive MN04020003E—April 2011 www.eaton.com Quick start parameters P1.2 0 = Basic 1 = Pump drive 2 = Fan drive 3 = Hoisting device (high load) Application P1.3 0 = EU 0 = EU 0 = EU 0 = EU Country specific default settings P6.1 1 = Control signal terminals (I/O) (I/O) P6.2 3 = AI1 (analog setpoint 1) 1 = Control signal terminals (I/O) (I/O) 3 = AI1 (analog setpoint 1) 1 = Control signal terminals (I/O) (I/O) 3 = AI1 (analog setpoint 1) 1 = Control signal terminals (I/O) (I/O) 3 = AI1 (analog setpoint 1) Primary remote control source Primary remote speed reference P6.3 0.00 Hz 20.00 Hz 20.00 Hz 0.00 Hz Minimum frequency P6.4 50.00 Hz 50.00 Hz 50.00 Hz 50.00 Hz Maximum frequency P6.5 3.0s 5.0s 20.0s 1.0s Acceleration time (acc1) P6.6 3.0s 5.0s 20.0s 1.0s Deceleration time (dec1) P6.7 0 = Ramp 0 = Ramp 0 = Ramp 0 = Ramp Start function (acceleration) (acceleration) (acceleration) (acceleration) P6.8 0 = Free coasting 1 = Deceleration time (ramp) 0 = Free coasting 0 = Free coasting Stop function P7.1 Ie Ie Ie Ie Motor, rated current P7.3 1440 RPM 1440 RPM 1440 RPM 1440 RPM Motor, rated speed (RPM) P7.4 0.85 0.85 0.85 0.85 Motor, power factor (cos ) P7.5 230/400/575V � 230/400/575V � 230/400/575V � 230/400/575V � Motor, rated operating voltage P7.6 60 Hz 60 Hz 60 Hz 60 Hz Motor, rated frequency P11.7 0 = Deactivated 0 = Deactivated 0 = Deactivated 1 = Enabled Torque increase M1.1 0.00 Hz 0.00 Hz 0.00 Hz 0.00 Hz Output frequency (display only)
Parameter Selection (P1) In the parameter selection (P1), you can choose between the factory set quick configuration (P1.1 = 1) with a reduced parameter set and all parameters (P1.1 = 0). The setting of the parameters with the quick configuration (P1.1 = 1) is guided by a Quickstart Wizard. (A listing of parameters is on Page 64.) Each executed parameter must be processed in succession up to frequency display M1.1. A return to a previous parameter is not possible here. The preset application parameters are selected under P1.2. Parameter Selections Parameters Only when the quick start assistant (M1.1) is completed can the parameters be called again and then also individually. With P1.1 = 0 (all parameters) and P1.2 = 0, 1, 2, or 3, you can link the predefined application values with all parameters. Every single parameter value is reset to factory settings every time that the application menu is activated. Access Factory Setting PNU ID RUN Value/Range Description (P1.3) P1.1 115 — Quick start parameters 1 0 All parameters All parameters are shown and can be changed 1 Only quick configuration parameters Only the selected parameters of the quick configuration are shown and can be changed (see Page 64 for list of parameters) P1.2 540 X — Application (See listing of the predefined application parameters in the table on Page 64) 0 0 Basic 1 Pump drive 2 Fan drive 3 High load (for example, hoisting or conveyor) P1.3 1472 X — Country specific default settings 0 0 EU (Europe, 50 Hz networks) 1 USA (North America, 60 Hz networks) — The country specific factory setting takes into account the frequency based parameters in relation to 50 and 60 Hz networks: PNU Designation P1.3 = 0 P1.3 = 1 P6.4 Maximum frequency 50 Hz 60 Hz P7.3 Motor, rated speed 1440 RPM 1720 RPM P7.6 Motor, rated frequency 50 Hz 60 Hz P11.2 Cut-off frequency 50 Hz 60 Hz P11.4 V/Hz characteristic curve, mean frequency value 25 Hz 30 Hz P14.3 Motor (2PS) nominal speed 1440 RPM 1720 RPM P14.6 Motor (2PS) nominal frequency 50 Hz 60 Hz P14.8 Maximum frequency (2PS) 50 Hz 60 Hz M-Max Series Adjustable Frequency Drive MN04020003E—April 2011 www.eaton.com 65
Page 1:
M-Max Series Adjustable Frequency D
Page 4 and 5:
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
About this Manual Input Supply Volt
Page 20 and 21:
M-Max Series Overview Component Ide
Page 22 and 23:
M-Max Series Overview Nameplate Rat
Page 24 and 25:
M-Max Series Overview Examples Labe
Page 26 and 27:
M-Max Series Overview General Rated
Page 28 and 29:
M-Max Series Overview Power Connect
Page 30 and 31: M-Max Series Overview Block Diagram
Page 32 and 33: M-Max Series Overview Proper Use Th
Page 34 and 35: Engineering Engineering Introductio
Page 36 and 37: Engineering Voltage Balance Because
Page 38 and 39: Engineering The leakage current to
Page 40 and 41: Engineering Motor and Circuit Type
Page 42 and 43: Installation Installation Introduct
Page 44 and 45: Installation Dismantling from Mount
Page 46 and 47: Installation EMC-Compliant Setup (E
Page 48 and 49: Installation Connection to Power Se
Page 50 and 51: Installation Arrangement and Connec
Page 52 and 53: Installation Connection on Control
Page 54 and 55: Installation Control Signal Termina
Page 56 and 57: Installation Analog Outputs The fre
Page 58 and 59: Installation Digital Outputs (Relay
Page 60 and 61: Installation Block Diagrams The fol
Page 62 and 63: Installation MMX32, MMX34 and MMX35
Page 64 and 65: Operation Operation Commissioning C
Page 66 and 67: Operation Commissioning with Contro
Page 68 and 69: Operation Start-Stop Command with M
Page 70 and 71: Error and Warning Messages Error an
Page 72 and 73: Error and Warning Messages List of
Page 74 and 75: Parameters Parameters Control Unit
Page 76 and 77: Parameters Setting Parameters The f
Page 78 and 79: Parameters Parameter Menu (PAR) You
Page 82 and 83: Parameters Analog Input (P2) In par
Page 84 and 85: Parameters Filter Time Constant The
Page 86 and 87: Parameters Digital Inputs PNU ID Ac
Page 88 and 89: Parameters Digital Inputs, continue
Page 90 and 91: Parameters Digital Inputs, continue
Page 92 and 93: Parameters Digital Outputs (P5) The
Page 94 and 95: Parameters Digital Outputs, continu
Page 96 and 97: Parameters Drives Control (P6) In t
Page 98 and 99: Parameters Drives Control, continue
Page 100 and 101: Parameters Drives Control, continue
Page 102 and 103: Parameters Motor (P7) For optimal o
Page 104 and 105: Parameters Protective Functions (P8
Page 106 and 107: Parameters Motor Heat Protection (P
Page 108 and 109: Parameters Protective Functions, co
Page 110 and 111: Parameters PID Controller, continue
Page 112 and 113: Parameters Activating/Deactivating
Page 114 and 115: Parameters Fixed Frequency Setpoint
Page 116 and 117: Parameters Sequence Control The seq
Page 118 and 119: Parameters Example A P10.9 = 1: Exe
Page 120 and 121: Parameters Example C Comparable exa
Page 122 and 123: Parameters V/Hz-Characteristic Curv
Page 124 and 125: Parameters On the constant three-ph
Page 126 and 127: Parameters Braking (P12) In paramet
Page 128 and 129: Parameters Braking, continued PNU I
Page 130 and 131:
Parameters Braking, continued PNU I
Page 132 and 133:
Parameters Logic Function (P13) The
Page 134 and 135:
Parameters Logic Function, continue
Page 136 and 137:
Parameters Second Parameter Set, co
Page 138 and 139:
Parameters Example 2 Stop function
Page 140 and 141:
Parameters System Parameter, contin
Page 142 and 143:
Parameters Operational Data Indicat
Page 144 and 145:
Parameters Setpoint Input (REF), co
Page 146 and 147:
Serial Interface (Modbus RTU) Modbu
Page 148 and 149:
Serial Interface (Modbus RTU) Struc
Page 150 and 151:
Serial Interface (Modbus RTU) Data
Page 152 and 153:
Serial Interface (Modbus RTU) Gener
Page 154 and 155:
Serial Interface (Modbus RTU) Expla
Page 156 and 157:
Appendix A Appendix A Special Techn
Page 158 and 159:
Appendix A Device Series MMX32 MMX3
Page 160 and 161:
Appendix A Device Series MMX35 MMX3
Page 162 and 163:
Appendix A Dimensions and Frame Siz
Page 164 and 165:
Appendix A Quick Start Parameter Gu
Page 166 and 167:
Appendix A All Parameters When firs
Page 168 and 169:
Appendix A Digital Input, continued
Page 170 and 171:
Appendix A Digital Output, continue
Page 172 and 173:
Appendix A Motor Access FS PNU ID R
Page 174 and 175:
Appendix A Fixed Frequencies Access
Page 176 and 177:
Appendix A Braking Access FS PNU ID
Page 178 and 179:
Appendix A Second Parameter Set Acc
Page 180 and 181:
Appendix A System Parameters, conti
Page 184:
Eaton’s Electrical Sector is a gl
show all

M-Maxâ„¢ Series Adjustable Frequency Drive - Eaton Corporation

Create successful ePaper yourself

Delete template?

Save as template?