2 .2 VALVESa. Solder: ASTM B32-96, 95-5 Tin-Antimony solder for above ground lines.b. Brazing: AWS A5.8-92, Classification BAg 1 (silver) where copper pipe isconnected to brass.3. Unions: ASME B16.22-95. Wrought copper solder joint, ground seat.4. Flanges: Class 125 cast bronze flanges.a. Bolts and Nuts: ASME B18.2.1-96, carbon steel square head machine bolts withgalvanized heavy hex nuts.b. Gaskets: ASME B16.21-92, nonmetallic, flat, 1/16-inch (2 mm), full faced, forwater service.5. Dielectric Unions: Threaded or soldered end connections for the pipe materials in whichinstalled. Constructed to isolate dissimilar metals, prevent galvanic action, and preventcorrosion.A. Gate Valves:1. 2-inch and smaller: Class 150, 300 psi ASTM B62-93 cast bronze body and union bonnet,solid bronze wedge, rising stem, integral seat, threaded ends, and aluminum or malleableironhandwheel.2. 2-1/2 inch and larger: Class 125, 200 psi, ASTM A126-95 cast-iron body and bonnet,solid cast-iron wedge, brass-alloy stem, outside screw and yoke, flanged end connectionsand cast-iron handwheel.B. Ball Valves: 2-inch and smaller: Class 150, 600-psi, ASTM B584-96 bronze body and bonnet,two-piece construction, chrome-plated brass ball, conventional port, bronze or brass stem, teflonseats and seals, threaded end connections, vinyl-covered steel handle and handle memory stop.C. Butterfly Valves: 2-1/2-inch and larger: 200 psi, ASTM A126-95 cast iron body and bonnet,stainless steel stem, field replaceable EPDM or Buna-N sleeve and stem seals, wafer, lug orgrooved style, nickel-plated ductile iron disc, lever operators with locks.D. Check Valves:1. Swing Check Valve: 2-1/2 Inch and Smaller: Class 150, 300-psi CWP, ASTM B62-93cast-bronze body and cap, horizontal swing, regrinding type, Y pattern, renewable bronzedisk. Threaded or soldered end connection.2. Wafer Check Valve: Class 125, 200-psi CWP, ASTM A126-95 cast iron body, bronzedisc/plates, stainless steel pins and springs, Buna N seals, installed between flanges.Valves designed to open and close at approximately one foot differential pressure.E. Balancing Valves: 125-psig working pressure, 250 degrees F maximum operating temperature,bronze body balance valves with connections for portable differential pressure meter. Meterconnections with integral check valves and seals, integral pointer and calibrated scale to registerdegree of valve opening. Threaded connections on valves 1-inch to 2-inches.15500-3HYDRONIC SYSTEMS
F. Safety Relief Valves: Brass or bronze body with brass and rubber, wetted, internal working parts.Valves designed, built, rated, and stamped in accordance with ASME Safety relief valves shallbe preset for 30 psi, non-adjustable, 3/4-inch inlet with 550,000 BTUH rating. Model 38B byAmtrol, West Warwick, RI, 02893 or approved equal.G. Automatic Fill Valve: Diaphragm operated, cast brass body, fill valve designed to maintain waterpressure in a closed water system. Valve shall include cleanable strainer, removable seatassembly, and built-in check valve. Valve shall have factory setting of 12 psig with fieldadjustment range of 10 to 25 psig . Maximum operating temperature shall be 225 degrees F.,maximum working pressure of 125 psig. Valve shall have 3/4-inch inlet and outlet. Model B7-12by ITT Bell and Gossett, Morton Grove, IL 660053; Model 11F by Amtrol, West Warwick, RI02893; or approved equal.H. Pressure Reducing Valve: ASSE 1003-93, water regulator, rated for initial working pressure of150 psig (1035 kPa) minimum, bronze body with threaded ends, integral factory-installed Y-pattern strainer, with adjustable reduced pressure range.2 .3 Backflow Preventer:A. Reduced Pressure: ASSE 1013-93 reduced pressure zone type backflow preventer suitable forcontinuous pressure applications. Include gate valves or ball valves on inlet and outlet, andstrainer on inlet, test cocks and pressure-differential relief valve with ASME A112.1.2-91 air-gapfitting located between 2 positive-seating check valves. Furnish with funnel drain.2 .4 PIPING ACCESSORIESA. Pressure Gauges: 3-1/2 inch dial, water service, bronze bourdon tube movement, cast aluminumcase, white face, black numbers, with gauge cock. Range at two times working pressure. Ametek,US Gauge Division, Sellersville, Pennsylvania, 18960 or approved equal.B. Thermometers:1. Red-reading tube, cast aluminum case, and separable sockets, including cap and chain.9-inch scales in mechanical equipment areas and on main piping; 7-inch scales in otherlocations. Accuracy shall be plus or minus 1 percent of range span. Vari-Angle by WeissInstruments, West Babylon, NY 11704 or approved equal.2. Ranges as follows:Heating WaterChilled Water30 to 300 degrees F30 to 100 degrees F1 degree divisions1 degree divisions3. For thermometers and wells through insulation, provide extensions to compensate forinsulation thickness.2 .5 Test Taps: Combination pressure and temperature test taps consisting of 1/4-inch or 1/2 inch nickelplated brass body MPT fitting designed to receive either temperature or pressure probe andgasketed and threaded cap with retention chain. Fittings shall be Pete's Plug, manufactured byPeterson Engineering Company, Richardson, Texas, or approved equal.A. Air Vents:15500-4HYDRONIC SYSTEMS
- Page 1 and 2:
RED FIR MAINTENANCE FACILITYHVAC CO
- Page 3 and 4:
DIVISION 3 - CONCRETE03300 Cast-In-
- Page 5 and 6:
1. Install new 9,200 gallon propane
- Page 7 and 8:
A. Prior to Mobilization1. Safety P
- Page 9 and 10:
SECTION 01120NATURAL FEATURES PROTE
- Page 11 and 12:
D. Fastening ropes, cables, or guys
- Page 13 and 14:
SECTION 01270DEFINITION OF BID ITEM
- Page 15 and 16:
SECTION 01310PROJECT MEETINGSPART 1
- Page 17 and 18:
SECTION 01330SUBMITTALSPART 1 GENER
- Page 19 and 20:
2. All sets of shop drawings, manuf
- Page 21 and 22:
TRANSMITTAL CONTINUATION - NATIONAL
- Page 23 and 24:
used in archeologically sensitive a
- Page 25 and 26:
1 .3 QUALITY ASSURANCEA. Clauses en
- Page 27 and 28:
SECTION 01420REFERENCE STANDARDSPAR
- Page 29 and 30:
NEMA National Electrical Manufactur
- Page 31 and 32:
B. Quality Control Staff: The Contr
- Page 33 and 34:
CONTRACTOR'S Q.C. DAILY REPORTREPOR
- Page 35 and 36:
TEST REPORT INFORMATION SHEETCONTRA
- Page 37 and 38:
C. When temporary connections are r
- Page 39 and 40:
SECTION 01520FIELD OFFICES AND SHED
- Page 41 and 42:
F. When pedestrian traffic is detou
- Page 43 and 44:
3 .3 AIR AND WATER POLLUTION CONTRO
- Page 45 and 46:
SECTION 01720FIELD ENGINEERINGPART
- Page 47 and 48:
C. On completion of the total proje
- Page 49 and 50:
A. Provide four complete sets of da
- Page 51 and 52:
EQUIPMENT DATA SHEETEquipment Item:
- Page 53 and 54:
I. Separate demolition area from bu
- Page 55 and 56:
A. Remove demolition debris daily o
- Page 57 and 58:
(d)Repairs or replacements are to b
- Page 59 and 60:
3 .2 DEMOLITIONA. Asphalt Concrete
- Page 61 and 62:
3 .3 DEMOLITIONA. Work systematical
- Page 63 and 64:
3 .3 EXCAVATIONA. Excavate to lines
- Page 65 and 66:
C. Make excavation large enough to
- Page 67 and 68:
3. After receipt of the written req
- Page 69 and 70:
D. Observe following trenching crit
- Page 71 and 72:
1. Under roadway crossings or pavem
- Page 73 and 74:
END OF SECTION02332-2WATERING
- Page 75 and 76:
A. Preparation: Install soil retent
- Page 77 and 78:
PART 3 EXECUTION3 .1 MARKING TAPEA.
- Page 79 and 80:
3.2 PERMANENT PAVEMENT REPLACEMENTA
- Page 81 and 82:
B. Cutting Existing Pavement: Contr
- Page 83 and 84:
SECTION 02725AGGREGATE BASE COURSEP
- Page 85 and 86:
B. Width: Plan dimension, plus or m
- Page 87 and 88:
B. Job-Mix Formula: Before producin
- Page 89 and 90:
2. The paver shall be equipped with
- Page 91 and 92:
C. A uniform compacted thickness sh
- Page 93 and 94:
2 .3 VINYL COATED POSTSA. Steel Pip
- Page 95 and 96:
E. Gate Hardware: Set keepers, stop
- Page 97 and 98:
SECTION 02855BOLLARDSPART 1 GENERAL
- Page 99 and 100:
SECTION 03300CAST-IN-PLACE CONCRETE
- Page 101 and 102:
1.4 SUBMITTALSA. Shop Drawings:1. A
- Page 103 and 104:
C. Chairs, Bolsters, Bar Supports,
- Page 105 and 106:
2.7 SLEEVESA. Unless noted otherwis
- Page 107 and 108:
C. Placement: Place reinforcement a
- Page 109 and 110:
B. Non-supporting forms (sides of c
- Page 111 and 112:
3.11 DAMAGED OR DEFECTIVE CONCRETEA
- Page 113 and 114:
B. Fine and coarse Aggregates1. Agg
- Page 115 and 116:
B. Mixing and Delivery1. Conform to
- Page 117 and 118:
SECTION 09900PAINTINGPART 1 - GENER
- Page 119 and 120:
B. Protect from freezing or damage.
- Page 121 and 122:
4. Remove by brush, air blast, or v
- Page 123 and 124:
Q. Assure hardware and accessories,
- Page 125 and 126:
SECTION 15050BASIC MATERIALS AND ME
- Page 127 and 128:
A. General: Provide adjustable pipe
- Page 129 and 130:
PIPE TYPEPIPE SIZE (INCHES)MAXIMUMS
- Page 131 and 132:
SECTION 15060PIPE AND PIPE FITTINGS
- Page 133 and 134:
1.6 DELIVERY, STORAGE, AND HANDLING
- Page 135 and 136:
B. Enter and exit through structure
- Page 137 and 138:
F. Prior to exposing the connection
- Page 139 and 140:
5. After required contact period, d
- Page 141 and 142:
PART 2 - PRODUCTS2.1 MANUFACTURERSA
- Page 143 and 144:
3.2 PREPARATIONA. Correct defects o
- Page 145 and 146:
SECTION 15064PIPE: PLASTIC (PVC) PR
- Page 147 and 148:
PART 3 - EXECUTION3.01 EXAMINATIONA
- Page 149 and 150:
3.05 CLEANINGA. Clean in accordance
- Page 151 and 152:
2 .2 ISOLATION HANGERSA. General: F
- Page 153 and 154:
H. Pipe: Provide seismic restraint
- Page 155 and 156:
A. Engraved anodized aluminum or en
- Page 157 and 158:
END OF SECTION15075-4MECHANICAL IDE
- Page 159 and 160:
B. Storage: Do not store materials
- Page 161 and 162:
equirements of 400 degrees Fahrenhe
- Page 163 and 164: SECTION 15090PIPE SUPPORT SYSTEMSPA
- Page 165 and 166: 3.4 SCHEDULEA. General: Locate pipe
- Page 167 and 168: C. Operation and Maintenance Manual
- Page 169 and 170: SECTION 15101GATE VALVESPART 1 - GE
- Page 171 and 172: 3.4 FIELD QUALITY CONTROLA. Repair
- Page 173 and 174: K. Products as manufactured by G.A.
- Page 175 and 176: 2.07 SILENT CHECKA. Ductile iron or
- Page 177 and 178: SECTION 15114SPECIAL VALVESPART 1 -
- Page 179 and 180: SECTION 15130PUMPSPART 1 GENERAL1 .
- Page 181 and 182: B. Install pumps in accordance with
- Page 183 and 184: F. Mount the remote meter display o
- Page 185 and 186: A. Cap all openings in pipes and va
- Page 187 and 188: 2. 1-1/2-inch to 2-inch: Flow capac
- Page 189 and 190: 3 .2 PIPE INSTALLATIONA. Clean all
- Page 191 and 192: d. If the meter test hand moves, ex
- Page 193 and 194: SECTION 15400PLUMBING SYSTEMSPART 1
- Page 195 and 196: 2 .7 PIPE SLEEVESA. As specified in
- Page 197 and 198: A. As specified in Section 15050.3
- Page 199 and 200: 3. Welders whose qualifications hav
- Page 201 and 202: 2) Gaskets: ASME B16.21-92. Gaskets
- Page 203 and 204: B. Tank shall be grit-blasted, prim
- Page 205 and 206: G. Internal Valves: 400-psi WOG, 15
- Page 207 and 208: B. Provide angle iron pipe supports
- Page 209 and 210: position. All propane system valves
- Page 211 and 212: 4. Pipe supports5. Bollards (see Se
- Page 213: 11. Include scale range, ratings, c
- Page 217 and 218: PART 3 EXECUTION3 .1 PIPE APPLICATI
- Page 219 and 220: B. Install thermometer wells in ver
- Page 221 and 222: 1. Location of automatic and manual
- Page 223 and 224: venting and sealed combustion. Insu
- Page 225 and 226: F. Automatic high limit shall shut
- Page 227 and 228: B. Filters: 1-inch thick pleated, 2
- Page 229 and 230: 4. Interconnection wiring diagrams
- Page 231 and 232: C. Electronic Operators: Operator s
- Page 233 and 234: A. Install a pressure gauge adjacen
- Page 235 and 236: B. Demonstrate complete system oper
- Page 237 and 238: B. Contractor shall furnish for app
- Page 239 and 240: A. General: Conduct tests in the pr
- Page 241 and 242: 4. Materials and equipment shall be
- Page 243 and 244: 3 .3 DEMONSTRATIONA. As specified i
- Page 245 and 246: 3. Raceways at vibrating equipment
- Page 247 and 248: A. Electrical Cabinet shall be NEMA
- Page 249 and 250: 3 .7 TRANSIENT VOLTAGE PROTECTIONA.
- Page 251 and 252: 3 .2 GROUND RINGA. Install conducto
- Page 253 and 254: SECTION 16131ELECTRICAL PULLBOXESPA
- Page 255 and 256: SECTION 16210ELECTRIC SERVICEPART 1
- Page 257 and 258: SECTION 16401UNDERGROUND SECONDARYP
- Page 259 and 260: PART 3 EXECUTION3 .1 EXTENSIONS INT
- Page 261 and 262: 3.2 INSTRUMENT CALIBRATIONA. The co
- Page 263 and 264: protected as recommended by the equ