Dismounted Reconnaissance Troop - Army Electronic Publications ...
Dismounted Reconnaissance Troop - Army Electronic Publications ...
Dismounted Reconnaissance Troop - Army Electronic Publications ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Chapter 6<br />
Rehearsals include all jumpers, the crew, the accompanying equipment, and support personnel.<br />
During live casting rehearsals, the leader emphasizes the commands, positions, and timing of<br />
body exit and water entry.<br />
All equipment attaches to the jumper with ¼-inch, 80-pound test cotton webbing. In or on this<br />
webbing, he normally carries a mask, fins, web belt with knife, flare(s), and life vest.<br />
6-27. When using rubber boats in conjunction with helocasting, the team must tie down and secure all<br />
equipment inside the boat, waterproof all equipment in the boat in case of submersion, and tape or pad all<br />
sharp edges or items.<br />
SECTION V – INFILTRATION<br />
6-28. Infiltration is a form of maneuver that the DRT uses to penetrate the threat security zone or main<br />
battle area to accomplish its mission. Infiltration often entails using stealthy forms of movement including<br />
movement by aerial and waterborne platforms. Small unmanned aircraft system assets may also be<br />
employed using infiltration to gain information if this is within system capabilities. Units planning this type<br />
of infiltration must acknowledge the risk of the SUAS being engaged and becoming unrecoverable.<br />
PURPOSE<br />
6-29. The primary focus of infiltration is to move to a designated point without being detected or engaged<br />
by the threat. During infiltration, the DRT elements use pre-designated lanes to reach their objective. The<br />
infiltrating elements employ cover, concealment, and stealth to move through identified or templated gaps<br />
in the threat.<br />
6-30. <strong>Dismounted</strong> reconnaissance troop elements infiltrate using a variety of movement methods.<br />
Infiltration may be conducted as an entire element at once or through movement into the area, by echelon,<br />
at different times.<br />
6-31. Purposes for infiltration include the following:<br />
Reconnoiter a specified area and establish OPs.<br />
Emplace remote sensors.<br />
PLANNING<br />
Establish communications relay capability for a specific period in support of other<br />
reconnaissance operations.<br />
Determine threat strengths and weaknesses.<br />
Locate unobserved routes through threat positions.<br />
Determine the location of high-payoff threat assets.<br />
Emplace small unit kill teams for interdiction missions.<br />
Recover SUASs to protect technologies from the enemy.<br />
Provide surveillance for follow-on echelons moving into the AO.<br />
6-32. Infiltration imposes a number of distinct, and often difficult, operational considerations on the DRT,<br />
which include methods of infiltration, extended operations time, reaction force requirements, CASEVAC<br />
resources, and escorted or covert exfiltration methods.<br />
6-33. The amount of intelligence information available to the commander during the planning process<br />
determines the risk involved in conducting the infiltration. Leaders conduct a thorough mission analysis,<br />
focusing on enemy activities in the areas of movement, historical locations of attacks, and likely areas of<br />
future ones to prevent accidental contact. While planning the operation, the commander must conduct IPB<br />
to include selecting appropriate routes and movement techniques based on the mission, the terrain and<br />
weather, the likelihood of threat contact, the expected or necessary speed of movement, and the depth to<br />
which elements must penetrate. The commander’s infiltration plan must provide elements with enough time<br />
for preparation and initial movement. The initial plan should also cover a CASEVAC, evasion, extraction,<br />
and reinforcement plan, as well as any special equipment requirements.<br />
6-6 ATTP 3-20.97 16 November 2010