Configuring Hardware and Communication Connections STEP 7.pdf

Router 11-6, 12-35
Routers 11-30
Routing 3-91
RTD Module 3-19
RTE Base Programming Interface 4-22
Rules for Arranging Modules (SIMATIC
300) 2-1
Rules for Arranging Modules (SIMATIC
400) 2-4
Rules for Configuring an ET 200S 3-17
Rules for Connecting Expansion Racks
(SIMATIC 400) 2-20
Rules for Creating Connections 12-28
Rules for Network Configuration 11-3
S
S5 Station 11-19
Object in NetPro 11-19
S7 Communication 12-18
S7 Connections 12-4, 12-8, 12-10, 12-11,
12-12, 12-34, 12-35, 12-36, 12-37, 16-24
Assigning Connection Resources 12-8
Blocks That Can Be Used 12-18
Interconnected Subnets for a PC Station
Through a Router 12-34
to a PG/PC 12-36
to a PG/PC with WinCC 12-37
S7 Connections (Interconnected Subnets)
12-34
S7 Connections (Redundant) 12-4
S7 Connections (Unspecified) 16-24
S7 Connections to Unspecified Connection
Partners 16-24
S7 Functions (S7 Communication) 12-2
S7 Slaves 3-4
S7 Subnet ID 16-16
S7-400H 10-1, 14-9
S7-Connections 12-41
S7RTM (see Component Configurator) 6-7
SAPI-S7 Interface 12-36
Saving a Configuration 7-1
Saving and Compiling 13-17
Saving and Compiling the GD Table for the
First Time 13-17
Saving Connections 12-43
Saving the Network Configuration 11-26
Scan Rates
Entering 13-18
Searching 1-10
in the Hardware Catalog 1-10
Searching in the Catalog (NetPro) 11-18
Searching in the Hardware Catalog 1-10
Segment 3-70, 3-71, 3-72, 3-73
Segment error 3-70, 3-73
Selecting a DP Mastersystem 11-27
Selecting and Arranging DP Slaves 3-13
Index
Selecting and Arranging IO Devices 4-16
Selecting Nodes on the Subnet (NetPro)
11-19
SEND/RECEIVE Interface 12-2, 12-9
Sending Global Data 13-9
SEND-RECEIVE Interface 12-3
Separating a DP Master System from the
PROFIBUS Interface 3-12
Setting a Specific Update Time for an IO-
Device 4-10
Setting Constant Bus Cycle Times
(PROFIBUS) 3-78
Setting Constant Bus Cycle Times for
PROFIBUS Subnets 3-78
Setting Priority Classes 1-6
Setting the Level of Protection 1-6
Setting the Properties of Components 1-6
Setting the Retentive Characteristics 1-6
Setting the System Reaction 1-6
Setting Update Times 5-5
SFB 12-26
BRCV 12-26
BSEND 12-26
GET 12-26
PUT 12-26
RESUME 12-26
START 12-26
STATUS 12-26
STOP 12-26
URCV 12-26
USEND 12-26
USTATUS 12-26
SFB 52 (read data record) 4-31
SFB 54 (read additional information on
interrupt) 4-31
SFB54 RALRM 3-61
SFB75 'SALRM' 3-42
SFC 126 'SYNC_PI' 3-82
SFC 127 'SYNC_PO' 3-82
SFC 78 'OB_RT' 3-82, 3-90
SFC126 'SYNC_PI' 3-87
SFC127 'SYNC_PO' 3-87
Shortening the Process Reaction Time by
Overlapping Ti and To 3-92
Showing and Hiding Columns 12-20
SIMATIC PC - Appending Configurations of
Previous Versions 6-5
SIMATIC PC Station 4-22, 6-1, 6-2, 6-3, 6-
4, 6-5, 11-19, 11-21, 12-33
Object in NetPro 11-19
SIMATIC PC Stations 4-22
SIMATIC PC-Station 12-34, 12-36
SIMATIC PDM 3-23, 3-24, 3-26
SIMATIC S5 12-43
Simulation Module SIM 374 IN/OUT 16 2-2
SIPROM (see SIMATIC PDM) 3-26
Slave 11-18
Configuring Hardware and Communication Connections with STEP 7
A5E00706939-01 9