Flamenco Technical Manual Revision 6.0 - Tunstall.de
Flamenco Technical Manual Revision 6.0 - Tunstall.de
Flamenco Technical Manual Revision 6.0 - Tunstall.de
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Konfigurationsanleitung - Seite 2 D Configuration Instructions - Page 2 GB<br />
ComStation T <strong>Flamenco</strong>, Best.‐Nr. 77 0606 20 ComStation T <strong>Flamenco</strong>, or<strong>de</strong>r no. 77 0606 20<br />
3. Optionale Einstellungen bei Bedarf vornehmen 3. Entering of optional settings<br />
Kontrast <strong>de</strong>s ComStation T ‐Displays einstellen (hoch, niedrig)<br />
Je nach Umgebungslicht ist die Einstellung “hoch” o<strong>de</strong>r “niedrig” besser lesbar.<br />
Mit <strong>de</strong>n Pfeiltasten “Kontrast” markieren; dann Kreistaste drücken.<br />
Mit <strong>de</strong>n Pfeiltasten “hoch” o<strong>de</strong>r “niedrig” markieren.<br />
Kreistaste drücken, um markierten Kontrast zu speichern.<br />
Tastenton ausschalten / einschalten<br />
Auf Wunsch kann <strong>de</strong>r Tastenton <strong>de</strong>r ComStation T ‐Tasten ausgeschaltet wer<strong>de</strong>n. Die<br />
Einstellung “Tastenton Ein” wird jedoch empfohlen.<br />
Mit <strong>de</strong>n Pfeiltasten “Tastenton” markieren; dann Kreistaste drücken.<br />
Mit <strong>de</strong>n Pfeiltasten “Ein” o<strong>de</strong>r “Aus” markieren.<br />
Kreistaste drücken, um die markierte Auswahl zu speichern.<br />
Störungston leise, mittel, laut o<strong>de</strong>r aus<br />
Warnung! Der Ton, <strong>de</strong>r auf Störungen aufmerksam macht, darf nur dann ausgeschaltet<br />
wer<strong>de</strong>n, wenn sichergestellt ist, dass Störungen auf an<strong>de</strong>re Art sicher angezeigt wer<strong>de</strong>n.<br />
Bei <strong>de</strong>r Lautstärke <strong>de</strong>s Störungstons kann gewählt wer<strong>de</strong>n zwischen leise, mittel und laut.<br />
Mit <strong>de</strong>n Pfeiltasten “Störungston” markieren; dann Kreistaste drücken.<br />
Mit <strong>de</strong>n Pfeiltasten “Leise”, „Mittel“, “Laut” o<strong>de</strong>r „Aus“ markieren.<br />
Kreistaste drücken, um die markierte Auswahl zu speichern.<br />
Softwarerevision anzeigen lassen<br />
Mit <strong>de</strong>n Pfeiltasten “Info” markieren; dann Kreistaste drücken.<br />
Softwarerevision <strong>de</strong>r ComStation T wird angezeigt.<br />
Haustaste drücken um zum Menü zurückzukehren.<br />
Setting of ComStation T display contrast (high, low)<br />
Depending on the ambient light a high or low display contrast is better legible.<br />
Mark “Contrast” using the arrow keys. Then press the circle key.<br />
Mark “high” or “low” using the arrow keys.<br />
Press the circle key to store the marked selection.<br />
Switching the key sound off or on<br />
If required the ComStation T key sound can be switched off. But the setting “Key sound On”<br />
is recommen<strong>de</strong>d.<br />
Mark “Key Sound” using the arrow keys. Then press the circle key.<br />
Mark “On” or “Off” using the arrow keys.<br />
Press the circle key to store the marked selection.<br />
Fault tone volume soft, medium, loud or off<br />
Warning! The tone that attracts attention for a fault may only be turned off, if it is ma<strong>de</strong> sure,<br />
that the attention is attracted in another way. The volume of the fault tone can be set to soft,<br />
medium or loud.<br />
Mark “Fault Tone” using the arrow keys. Then press the circle key.<br />
Mark “Soft“, “Medium“, “Loud“ or „Off“ using the arrow keys.<br />
Press the circle key to store the marked selection.<br />
Displaying the software revision<br />
Mark “Info” using the arrow keys. Then press the circle key.<br />
The software revision for the ComStation T is displayed.<br />
Press the home key to return to the menu.<br />
4. Zimmerbus RAN prüfen 4. Checking room bus RAN<br />
Status<br />
Prüfung, ob eingestellte RAN Anzahl (siehe oben “RAN Anzahl einstellen”) mit Anzahl<br />
funktionsbereiter Zimmergeräte übereinstimmt.<br />
Mit <strong>de</strong>n Pfeiltasten “RAN” markieren; dann Kreistaste drücken.<br />
Mit <strong>de</strong>n Pfeiltasten “Status” markieren; dann Kreistaste drücken.<br />
Anzeige: OK: ComStation T hat gemel<strong>de</strong>t, dass eingestellte RAN Anzahl gleich Anzahl<br />
funktionsbereiter Zimmergeräte ist.<br />
Anzeige: Fehler: ComStation T hat gemel<strong>de</strong>t, dass eingestellte RAN Anzahl nicht gleich<br />
Anzahl funktionsbereiter Zimmergeräte ist.<br />
Zum Verlassen <strong>de</strong>r Anzeige Haustaste drücken. Bei Fehler “Test RAN” durchführen.<br />
Test RAN<br />
Test, ob Zimmergeräte funktionsbereit und korrekt am RAN angeschlossen sind.<br />
Mit <strong>de</strong>n Pfeiltasten “RAN” markieren; dann Kreistaste drücken.<br />
Test Starten: Mit <strong>de</strong>n Pfeiltasten “Test RAN” markieren; dann Kreistaste drücken.<br />
Die LEDs aller angeschlossenen Zimmergeräte müssen blinken. (Geräte, die nicht<br />
blinken, sind falsch angeschlossen o<strong>de</strong>r <strong>de</strong>fekt. Defekte Geräte austauschen. Falsch<br />
angeschlossene Geräte korrekt anschließen.)<br />
Prüfen, ob Anzahl angeschlossener Zimmergeräte gleich <strong>de</strong>r eingestellten RAN Anzahl<br />
ist. Falls eingestellte RAN‐Anzahl falsch ist, diese nach <strong>de</strong>m RAN Test wie oben beschrieben<br />
einstellen.<br />
Test been<strong>de</strong>n: Haustaste drücken.<br />
5. Konfigurationsmenü verlassen 5. Exit the configuration menu<br />
Wenn keine Einstellungen mehr vorgenommen wer<strong>de</strong>n sollen und alle Tests been<strong>de</strong>t sind,<br />
müssen Sie das Konfigurationsmenü verlassen.<br />
Haustaste so oft drücken, bis die normale Betriebsanzeige angezeigt wird.<br />
Hinweis: Wenn drei Minuten keine Funktionstaste gedrückt wird, wird das<br />
Konfigurationsmenü automatisch verlassen.<br />
Status<br />
Check whether the stored RAN number (see above “Setting of RAN number”) is equal to the<br />
number of operational room <strong>de</strong>vices.<br />
Mark “RAN” using the arrow keys. Then press the circle key.<br />
Mark “Status” using the arrow keys. Then press the circle key.<br />
Display: OK: ComStation T has reported: Stored RAN number is equal to the number of<br />
operational room <strong>de</strong>vices.<br />
Display: Error: ComStation T has reported: Stored RAN number is not equal to the<br />
number of operational room <strong>de</strong>vices.<br />
Press the home key to end. In case of an error carry out “Test RAN”.<br />
Test RAN<br />
Test if room <strong>de</strong>vices are ready to operate and if they are correctly connected to the RAN.<br />
Check the correct setting of the RAN number.<br />
Mark “RAN” using the arrow keys. Then press the circle key.<br />
Test start: Mark “Test RAN” using the arrow keys. Then press the circle key.<br />
The LEDs of all connected room <strong>de</strong>vices must flash. (Non-flashing <strong>de</strong>vices are wrongly<br />
connected or <strong>de</strong>fective. Replace <strong>de</strong>fective <strong>de</strong>vices. Correct any wrong connection.)<br />
Compare the number of connected room <strong>de</strong>vices with the stored RAN number. If the<br />
stored RAN number is not equal to the number of connected room <strong>de</strong>vices, correct the<br />
RAN number setting after the RAN test as <strong>de</strong>scribed above.<br />
End of test: Press the home key.<br />
When all settings are performed and all tests are finished, exit the configuration menu.<br />
During this procedure all settings are stored.<br />
Press home key until normal operation display appears.<br />
Note: If for a period of three minutes no function key is pressed, the system will leave the<br />
configuration menu.<br />
<strong>Tunstall</strong> GmbH, Orkotten 66, D-48291 Telgte, www.tunstall.<strong>de</strong><br />
74 0452 30<br />
Steckvorrichtung ComStation<br />
Connection socket ComStation<br />
77 0606 20<br />
ComStation T <strong>Flamenco</strong> ®<br />
00 8801 14, 11/12 (Rev. 1.0)<br />
Page 142