Flamenco Technical Manual Revision 6.0 - Tunstall.de

More documents

Recommendations

Info

Battery Set for UPS 60, Order No. 77 3450 00 Dimensional drawing: 2. Connection The connection terminals are provided as cage srew/plug-in clamps. 1. Release 6 fastening screws for the cover and remove the cover to the front. Now, the terminal connection clamps are accessible. 2. Direct the connection cable through the cable duct into the power supply unit and connect to the appropriate terminal posts as designated in the power supply unit. CAUTION! Check for the correct connection, orientation and screwing. 3. Secure the connection cable against being pulled from the housing for example by fixing the installation cable with the screwed cable gland. 2.1 Battery test The power supply unit features an automatic battery load test. The battery load test is an effective instrument for checking the true battery state. A negative result, i.e. a warning message is issued, may be caused by one or more of the following: • Charge status too low. • Battery fuse has failed. • Battery not correctly connected. • Battery is defective. • Battery is too old, and must be replaced. English - 2 © Tunstall GmbH, Orkotten 66, 48291 Telgte, Germany, www.tunstall.de, 00 8802 82, Rev. 2.2 (05/2012) Page 198
Battery Set for UPS 60, Order No. 77 3450 00 3. Service To ensure the safe function of the system, batteries should be replaced every 3 years - depending on the ambient temperature (Refer to diagram 1, Item 4). After 3 – 5 years, the battery capacity has dropped to approx. 60%. 4. Battery service life The battery set UPS 60 comes with sealed, service-free and rechargeable lead-gel batteries VRLA. According to the EUROBAT classification, these batteries have a useful service life of 5 – 7 years. This time, however, strongly depends on the relevant ambient temperature. (Up to 20 °C: 7 – 8 years as shown in diagram 1) If the system will not be used for an extended period of time, the batteries should be fully charged to prevent a total discharge. (Refer to item 5 "Storage") While the system is not used, the battery fuse (located between the two batteries) has to be removed to prevent total discharge. After the charging process has been completed, the battery set for UPS 60 has to be disconnected from the power supply unit UPS 60 by disconnecting the battery connection cable (see chapter 2.) or by removing the battery fuse. Battery service life (years) Temperature Diagram 1: Battery service life in relation to ambient temperature 4.1 Battery change Lead-gel batteries contain harmful toxic substances. Observe valid safety directives when during handling and transport. For disposal, comply with local directives. Pb Batteries bear the risk of excessive short-circuit currents. Never create any direct contact between the battery posts and or other conductive component parts. Therefore remove any wristband, watch, finger rings or other metal objects when working at the open unit. Always use tools with standard isolating handles. Batteries may be replaced only by the same type of battery (2 x 12 V; 24 Ah). We recommend the use of the battery type BAT 12-24, Tunstall Order No. 00 0648 87. The use of other makes may create problems due to different connecting terminals or differing dimensions. 1. Shut off mains supply to the power supply unit UPS !!! 2. Release the 6 fastening screws for the cover and remove the cover to the front. 3. Confirm the position of the old batteries and after their removal, install the new batteries in the same manner. 4. Make sure, the new batteries are in the same position and check for the correct battery contacts. False connections may damage the power supply unit UPS ! 5. Put the rubber grommets back on the connection screws. 6. Fix the battery position by securing it with the Velcro tape. © Tunstall GmbH, Orkotten 66, 48291 Telgte, Germany, www.tunstall.de, 00 8802 82, Rev. 2.2 (05/2012) English - 3 Page 199
Page 2 and 3:
The manual was prepared with due ca
Page 4 and 5:
10. Configure the OSY-ControlCenter
Page 6 and 7:
1. Safety Comply with all generally
Page 8 and 9:
1. Safety 1.6 Technical standards C
Page 10 and 11:
2. Necessary previous knowledge 2.2
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
3. Room types 3.1 Patient / residen
Page 18 and 19:
3. Room types 3.1.2 Patient / Resid
Page 20 and 21:
3. Room types 3.1.3 Patient / resid
Page 22 and 23:
3. Room types 3.1.4 Patient room: L
Page 24 and 25:
3. Room types 3.1.5.2 Patient room:
Page 26 and 27:
3. Room types 3.1.6 Patient room: S
Page 28 and 29:
3. Room types 3.3 Ward bathroom 3.3
Page 30 and 31:
3. Room types 3.4 Nurse station 3.4
Page 32 and 33:
3. Room types 3.4.3 Nurse station:
Page 34 and 35:
3. Room types 3.4.5 Nurse station:
Page 36 and 37:
3. Room types 34 Flamenco - Technic
Page 38 and 39:
4. Installation examples 230 V AC 7
Page 40 and 41:
4. Installation examples 77 0510 00
Page 42 and 43:
4. Installation examples 40 Flamenc
Page 44 and 45:
5. Installation work sequence 42 Fl
Page 46 and 47:
6. Defining the mounting positions
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
7. Installing the back boxes Connec
Page 54 and 55:
8. Laying the cables 8.2 Electromag
Page 56 and 57:
8. Laying the cables 8.4 Current de
Page 58 and 59:
8. Laying the cables 8.5 Group bus
Page 60 and 61:
8. Laying the cables 8.5.4 Maximum
Page 62 and 63:
8. Laying the cables Not service-fr
Page 64 and 65:
9. Activating the power supply 9.2.
Page 66 and 67:
10. Configure the OSY-ControlCenter
Page 68 and 69:
11. Voltage surge protection 11.1 S
Page 70 and 71:
11. Voltage surge protection Buildi
Page 72 and 73:
12. Functional checks 12.1 Checking
Page 74 and 75:
12. Functional checks 12.1.2.2 Chec
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
13. Spare parts Functions Screw con
Page 82 and 83:
13. Spare parts Functions Connectin
Page 84 and 85:
13. Spare parts 82 Flamenco - Techn
Page 86 and 87:
14. Product leaflets Order no. Prod
Page 88 and 89:
14. Product leaflets Flamenco - Tec
Page 90 and 91:
Installationsanleitung D Installati
Page 92 and 93:
Anschlüsse D Connections GB Anschl
Page 94 and 95:
Anschlüsse D Connections GB Anschl
Page 96 and 97:
Page 98 and 99:
Anschlüsse D Connections GB 77 018
Page 100 and 101:
14. Product leaflets Flamenco - Tec
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
14. Product leaflets Page 106 Flame
Page 110 and 111:
Page 112 and 113:
Konfigurationsanleitung - Seite 1 D
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Anschlüsse D Connections GB Contro
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Anschlüsse D Connections GB Zum An
Page 130 and 131:
Anschlüsse D Connections GB ELA EL
Page 132 and 133:
Anschlüsse am Anschlussfeld D Conn
Page 134 and 135:
Anschlüsse D Connections GB Zimmer
Page 136 and 137:
Anschlüsse am Anschlussfeld D Conn
Page 138 and 139:
Anschlüsse D Connections GB ComSta
Page 140 and 141:
Page 138
Page 142 and 143:
Konfigurationsanleitung - Seite 2 -
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151: Installationsanleitung D Installati
Page 170 and 171: I I I I Anschlüsse D Connections G
Page 174 and 175: Anschlussplan für Rauchmelder, Bes
Page 178 and 179: Anschlüsse D Connections GB Gefahr
Page 180 and 181: Kontrollanzeigen (LED) D Control LE
Page 182 and 183: Anschlüsse D Connections GB Ip Ip
Page 184 and 185: Power supply unit UPS, Order No. 77
Page 190 and 191: Power supply unit UPS 60, Order No.
Page 196 and 197: Power supply unit, Order No. 77 340
Page 198 and 199: Power supply unit, Order No. 77 340
Page 202 and 203: Battery Set for UPS 60, Order No. 7
Page 206: 14. Product leaflets Page 204 Flame
show all

Flamenco Technical Manual Revision 6.0 - Tunstall.de

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?