M16C/62 Group DATASHEET

More documents

Recommendations

Info

Appendix Standard Serial I/O Mode (Flash Memory Version)Mitsubishi microcomputersM16C / 62 GroupSINGLE-CHIP 16-BIT CMOS MICROCOMPUTERProgram Status After Program (SR3)If excessive data is written (phenomenon whereby the memory cell becomes depressed which resultsin data not being read correctly), “1” is set for the program status after-program at the end of the pagewrite operation. In other words, when writing ends successfully, “8016” is output; when writing fails,“9016” is output; and when excessive data is written, “8816” is output.If “1” is written for any of the SR5, SR4 or SR3 bits, the page program, block erase, erase all unlockedblocks and lock bit program commands are not accepted. Before executing these commands, executethe clear status register command (5016) and clear the status register.267
Appendix Standard Serial I/O Mode (Flash Memory Version)Mitsubishi microcomputersM16C / 62 GroupSINGLE-CHIP 16-BIT CMOS MICROCOMPUTERStatus Register 1 (SRD1)Status register 1 indicates the status of serial communications, results from ID checks and results fromcheck sum comparisons. It can be read after the SRD by writing the read status register command (7016).Also, status register 1 is cleared by writing the clear status register command (5016).Table 1.31.3 gives the definition of each status register 1 bit. “0016” is output when power is turned ONand the flag status is maintained even after the reset.Table 1.31.3. Status register 1 (SRD1)SRD1 bitsSR15 (bit7)SR14 (bit6)SR13 (bit5)SR12 (bit4)SR11 (bit3)SR10 (bit2)Status nameBoot update completed bitReservedReservedChecksum match bitID check completed bitsDefinition"1" "0"Update completed--Match00011011Not update--MismatchNot verifiedVerification mismatchReservedVerifiedSR9 (bit1)Data receive time outTime outNormal operationSR8 (bit0)Reserved--Boot Update Completed Bit (SR15)This flag indicates whether the control program was downloaded to the RAM or not, using the downloadfunction.Check Sum Consistency Bit (SR12)This flag indicates whether the check sum matches or not when a program, is downloaded for executionusing the download function.ID Check Completed Bits (SR11 and SR10)These flags indicate the result of ID checks. Some commands cannot be accepted without an IDcheck.Data Reception Time Out (SR9)This flag indicates when a time out error is generated during data reception. If this flag is attachedduring data reception, the received data is discarded and the microcomputer returns to the commandwait state.268
Page 1 and 2:
Customer Interface Publication: KCH
Page 3:
DescriptionMitsubishi microcomputer
Page 7 and 8:
DescriptionMitsubishi microcomputer
Page 9 and 10:
Pin DescriptionMitsubishi microcomp
Page 11 and 12:
MemoryMitsubishi microcomputersM16C
Page 13 and 14:
CPUMitsubishi microcomputersM16C /
Page 15 and 16:
ResetMitsubishi microcomputersM16C
Page 17 and 18:
ResetMitsubishi microcomputersM16C
Page 19 and 20:
SFRMitsubishi microcomputersM16C /
Page 21 and 22:
SFRMitsubishi microcomputersM16C /
Page 23 and 24:
Memory Space Expansion FunctionsMit
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Processor ModeMitsubishi microcompu
Page 31 and 32:
Processor ModeMitsubishi microcompu
Page 33 and 34:
Bus SettingsMitsubishi microcompute
Page 35 and 36:
Bus ControlMitsubishi microcomputer
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Clock Generating CircuitMitsubishi
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Status Transition Of BCLKMitsubishi
Page 49 and 50:
Power controlMitsubishi microcomput
Page 51 and 52:
InterruptMitsubishi microcomputersM
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
________NMI InterruptMitsubishi mic
Page 69 and 70:
Precautions for InterruptsMitsubish
Page 71 and 72:
Watchdog TimerMitsubishi microcompu
Page 73 and 74:
DMACMitsubishi microcomputersM16C /
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
TimerMitsubishi microcomputersM16C
Page 85 and 86:
Timer AMitsubishi microcomputersM16
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Timer BMitsubishi microcomputersM16
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Timers’ functions for three-phase
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Serial I/OMitsubishi microcomputers
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Clock synchronous serial I/O modeMi
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Clock asynchronous serial I/O (UART
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
UART2 Special Mode RegisterMitsubis
Page 143 and 144:
UART2 Special Mode RegisterMitsubis
Page 145 and 146:
UART2 Special Mode Register 2Mitsub
Page 147 and 148:
UART2 Special Mode Register 2Mitsub
Page 149 and 150:
S I/O3, 4Mitsubishi microcomputersM
Page 151 and 152:
S I/O3, 4Mitsubishi microcomputersM
Page 153 and 154:
A-D ConverterMitsubishi microcomput
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
D-A ConverterMitsubishi microcomput
Page 165 and 166:
CRCMitsubishi microcomputersM16C /
Page 167 and 168:
Programmable I/O PortMitsubishi mic
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Usage precautionMitsubishi microcom
Page 179 and 180:
Usage precautionMitsubishi microcom
Page 181 and 182:
Mitsubishi microcomputersM16C / 62
Page 183 and 184:
Operating maximum frequency [MHZ]Op
Page 185 and 186:
Electrical characteristics (Vcc = 5
Page 187 and 188:
Timing (VCC=5V)Mitsubishi microcomp
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Timing (Vcc = 5V)Mitsubishi microco
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Electrical characteristics (Vcc = 3
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
IssuancesignatureReceiptMitsubishi
Page 213 and 214:
Page 215 and 216:
Page 217 and 218: IssuancesignatureReceiptMitsubishi
Page 219 and 220: Mitsubishi microcomputersM16C / 62
Page 235 and 236: Operating maximum frequency [MHZ]De
Page 237 and 238: CPU Rewrite Mode (Flash Memory Vers
Page 251 and 252: Functions To Inhibit Rewriting (Fla
Page 253 and 254: Appendix Standard Serial I/O Mode (
Page 255 and 256: CNVSSRESETP93/DA0/TB3INP94/DA1/TB4I
Page 267: Appendix Standard Serial I/O Mode (
Page 273 and 274: 272Mitsubishi microcomputersM16C /
Page 277: MITSUBISHI SEMICONDUCTORSM16C/62 Gr
show all

M16C/62 Group DATASHEET

Create successful ePaper yourself

Delete template?

Save as template?