M16C/62 Group DATASHEET

More documents

Recommendations

Info

Clock Generating CircuitMitsubishi microcomputersM16C / 62 GroupSINGLE-CHIP 16-BIT CMOS MICROCOMPUTERClock ControlFigure 1.13.3 shows the block diagram of the clock generating circuit.RESETSoftware resetNMICM10 “1”Write signalXCIN XCOUTCM04Sub clockS QXIN XOUTRMain clockCM05CM021/32fCfC32f1fADb cad Dividerf8f32CM07=0fCCM07=1f1SIO2f8SIO2f32SIO2BCLKInterrupt requestlevel judgmentoutputS QWAIT instructionRbca1/2 1/2 1/2 1/21/2CM06=1CM06=0CM17,CM16=10CM06=0CM17,CM16=11dCM0i : Bit i at address 000616CM1i : Bit i at address 000716WDCi : Bit i at address 000F16CM06=0CM17,CM16=00CM06=0CM17,CM16=01Details of dividerFigure 1.13.3. Clock generating circuit41
Clock Generating CircuitMitsubishi microcomputersM16C / 62 GroupSINGLE-CHIP 16-BIT CMOS MICROCOMPUTERThe following paragraphs describes the clocks generated by the clock generating circuit.(1) Main clockThe main clock is generated by the main clock oscillation circuit. After a reset, the clock is divided by 8 tothe BCLK. The clock can be stopped using the main clock stop bit (bit 5 at address 000616). Stopping theclock, after switching the operating clock source of CPU to the sub-clock, reduces the power dissipation.After the oscillation of the main clock oscillation circuit has stabilized, the drive capacity of the main clockoscillation circuit can be reduced using the XIN-XOUT drive capacity select bit (bit 5 at address 000716).Reducing the drive capacity of the main clock oscillation circuit reduces the power dissipation. This bitchanges to “1” when shifting from high-speed/medium-speed mode to stop mode and at a reset. Whenshifting from low-speed/low power dissipation mode to stop mode, the value before stop mode is retained.(2) Sub-clockThe sub-clock is generated by the sub-clock oscillation circuit. No sub-clock is generated after a reset.After oscillation is started using the port Xc select bit (bit 4 at address 000616), the sub-clock can beselected as the BCLK by using the system clock select bit (bit 7 at address 000616). However, be surethat the sub-clock oscillation has fully stabilized before switching.After the oscillation of the sub-clock oscillation circuit has stabilized, the drive capacity of the sub-clockoscillation circuit can be reduced using the XCIN-XCOUT drive capacity select bit (bit 3 at address 000616).Reducing the drive capacity of the sub-clock oscillation circuit reduces the power dissipation. This bitchanges to “1” when shifting to stop mode and at a reset.(3) BCLKThe BCLK is the clock that drives the CPU, and is fc or the clock is derived by dividing the main clock by1, 2, 4, 8, or 16. The BCLK is derived by dividing the main clock by 8 after a reset. The BCLK signal canbe output from BCLK pin by the BCLK output disable bit (bit 7 at address 000416) in the memory expansionand the microprocessor modes.The main clock division select bit 0(bit 6 at address 000616) changes to “1” when shifting from highspeed/medium-speedto stop mode and at reset. When shifting from low-speed/low power dissipationmode to stop mode, the value before stop mode is retained.(4) Peripheral function clock(f1, f8, f32, f1SIO2, f8SIO2,f32SIO2,fAD)The clock for the peripheral devices is derived from the main clock or by dividing it by 1, 8, or 32. Theperipheral function clock is stopped by stopping the main clock or by setting the WAIT peripheral functionclock stop bit (bit 2 at 000616) to “1” and then executing a WAIT instruction.(5) fC32This clock is derived by dividing the sub-clock by 32. It is used for the timer A and timer B counts.(6) fCThis clock has the same frequency as the sub-clock. It is used for the BCLK and for the watchdog timer.42
Page 1 and 2: Customer Interface Publication: KCH
Page 3: DescriptionMitsubishi microcomputer
Page 7 and 8: DescriptionMitsubishi microcomputer
Page 9 and 10: Pin DescriptionMitsubishi microcomp
Page 11 and 12: MemoryMitsubishi microcomputersM16C
Page 13 and 14: CPUMitsubishi microcomputersM16C /
Page 15 and 16: ResetMitsubishi microcomputersM16C
Page 17 and 18: ResetMitsubishi microcomputersM16C
Page 19 and 20: SFRMitsubishi microcomputersM16C /
Page 21 and 22: SFRMitsubishi microcomputersM16C /
Page 23 and 24: Memory Space Expansion FunctionsMit
Page 29 and 30: Processor ModeMitsubishi microcompu
Page 31 and 32: Processor ModeMitsubishi microcompu
Page 33 and 34: Bus SettingsMitsubishi microcompute
Page 35 and 36: Bus ControlMitsubishi microcomputer
Page 41: Clock Generating CircuitMitsubishi
Page 45 and 46: Clock Generating CircuitMitsubishi
Page 47 and 48: Status Transition Of BCLKMitsubishi
Page 49 and 50: Power controlMitsubishi microcomput
Page 51 and 52: InterruptMitsubishi microcomputersM
Page 67 and 68: ________NMI InterruptMitsubishi mic
Page 69 and 70: Precautions for InterruptsMitsubish
Page 71 and 72: Watchdog TimerMitsubishi microcompu
Page 73 and 74: DMACMitsubishi microcomputersM16C /
Page 83 and 84: TimerMitsubishi microcomputersM16C
Page 85 and 86: Timer AMitsubishi microcomputersM16
Page 93 and 94:
Timer AMitsubishi microcomputersM16
Page 95 and 96:
Timer BMitsubishi microcomputersM16
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Timers’ functions for three-phase
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Serial I/OMitsubishi microcomputers
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Clock synchronous serial I/O modeMi
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Clock asynchronous serial I/O (UART
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
UART2 Special Mode RegisterMitsubis
Page 143 and 144:
UART2 Special Mode RegisterMitsubis
Page 145 and 146:
UART2 Special Mode Register 2Mitsub
Page 147 and 148:
UART2 Special Mode Register 2Mitsub
Page 149 and 150:
S I/O3, 4Mitsubishi microcomputersM
Page 151 and 152:
S I/O3, 4Mitsubishi microcomputersM
Page 153 and 154:
A-D ConverterMitsubishi microcomput
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
D-A ConverterMitsubishi microcomput
Page 165 and 166:
CRCMitsubishi microcomputersM16C /
Page 167 and 168:
Programmable I/O PortMitsubishi mic
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Usage precautionMitsubishi microcom
Page 179 and 180:
Usage precautionMitsubishi microcom
Page 181 and 182:
Mitsubishi microcomputersM16C / 62
Page 183 and 184:
Operating maximum frequency [MHZ]Op
Page 185 and 186:
Electrical characteristics (Vcc = 5
Page 187 and 188:
Timing (VCC=5V)Mitsubishi microcomp
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Timing (Vcc = 5V)Mitsubishi microco
Page 195 and 196:
Page 197 and 198:
Page 199 and 200:
Electrical characteristics (Vcc = 3
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
IssuancesignatureReceiptMitsubishi
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Operating maximum frequency [MHZ]De
Page 237 and 238:
CPU Rewrite Mode (Flash Memory Vers
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Functions To Inhibit Rewriting (Fla
Page 253 and 254:
Appendix Standard Serial I/O Mode (
Page 255 and 256:
CNVSSRESETP93/DA0/TB3INP94/DA1/TB4I
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
272Mitsubishi microcomputersM16C /
Page 275 and 276:
Page 277:
MITSUBISHI SEMICONDUCTORSM16C/62 Gr
show all

M16C/62 Group DATASHEET

Create successful ePaper yourself

Delete template?

Save as template?