Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP

More documents

Recommendations

Info

Table 53 Liebert NXL SA, SR, SN, MM, CD - Glossary 164 Modbus 485 and Modbus IP Protocols - UPS Systems Data Label Data Description Auto Restart In Progress Auto restart is in progress Auto Restart Inhibited - Ext Auto restart inhibited due to an external signal Automatic Restart Failed Automatic restart failed Backfeed Breaker Open The backfeed breaker is in the open position Backfeed Breaker Backfeed breaker Battery - External Monitor 1 External battery monitor 1 - battery maintenance required Battery - External Monitor 2 External battery monitor 2 - battery maintenance required Battery Amp-Hours Consumed This Discharge Battery amp-hours withdrawn this discharge. Battery Amp-Hours Consumed Cumulative battery amp-hours withdrawn over the life of the battery Battery Automatic Test Inhibited Automatic (scheduled) battery tests are inhibited Battery Capacity Low Battery capacity is low Battery Cell Count - Lead Acid Battery cell count - lead acid Battery Cell Count-Nickel Cadmium Battery cell count - nickel cadmium Battery Charging Error The battery is not charging properly Battery Charging Inhibited Battery charging is inhibited due to an external inhibit signal Battery Charging Reduced-Extrnl Using a reduced battery charging algorithm due to an external signal Battery Circuit Breaker 1 Open Battery circuit breaker 1 is open Battery Circuit Breaker 2 Open Battery circuit breaker 2 is open Battery Circuit Breaker 3 Open Battery circuit breaker 3 is open Battery Circuit Breaker 4 Open Battery circuit breaker 4 is open Battery Circuit Breaker 5 Open Battery circuit breaker 5 is open Battery Circuit Breaker 6 Open Battery circuit breaker 6 is open Battery Circuit Breaker 7 Open Battery circuit breaker 7 is open Battery Circuit Breaker 8 Open Battery circuit breaker 8 is open Battery Commission Date Date and time when battery placed into service Battery Discharge Power Instantaneous battery power while discharging Battery Discharge Time The time on battery operation for this discharge Battery Discharging The battery is discharging Battery Equalize The rectifier output voltage is increased to equalize the battery voltage level. Battery Ground Fault Battery system ground fault amperage exceeds the threshold Battery Last Discharge Date The date and time of the last battery discharge Battery Low Shutdown Battery disconnect due to end-of-discharge. Battery Low The calculated battery time remaining has reached the low battery threshold Battery Over Temperature A battery temperature sensor is reporting a value above a threshold Battery Percentage Charge The percentage of battery charge Battery Self Test Battery self test is in progress Battery Temperature for Cabinet The battery temperature for a cabinet Battery Temperature Imbalance Excessive temperature differences between battery sensors detected Battery Temperature Sensor Fault A battery temperature sensor fault has been detected Battery Test Failed Battery test failed Battery Time Remaining The calculated available time on battery Battery Total Discharge Time The cumulative battery discharge time
Table 53 Liebert NXL SA, SR, SN, MM, CD - Glossary (continued) Data Label Data Description 165 Modbus 485 and Modbus IP Protocols - UPS Systems Battery Volts at Main Disconnect The voltage between the positive and the negative battery terminals of the common battery disconnect Battery Volts for Cabinet The voltage between the positive and negative battery terminals of a battery cabinet BPSS Startup Inhibit The Bypass Static Switch startup is inhibited Bypass - Excess Auto Retransfers The number of auto retransfers, from bypass to inverter, has exceeded the maximum for a specified time interval Bypass - Manual Rexfr Inhibited Manual transfer from bypass to inverter is inhibited. Bypass - Manual Xfr Inhibited Manual transfer from inverter to bypass is inhibited. Bypass Auto Retransfer Failed After performing a recoverable transfer to bypass, an attempt to auto retransfer from bypass to inverter failed Bypass Auto Transfer Failed An automatic transfer to static bypass failed Bypass Excessive Pulse Parallel The system has performed too many pulse parallel operations within a specified time interval Bypass Frequency Error The bypass frequency is outside the inverter synchronization limits Bypass Input Frequency The bypass input frequency Bypass Input Voltage RMS A-B The bypass input RMS voltage between phases A and B Bypass Input Voltage RMS B-C The bypass input RMS voltage between phases B and C Bypass Input Voltage RMS C-A The bypass input RMS voltage between phases C and A Bypass Input Wire Configuration Bypass input wire configuration Bypass Isolation Breaker (BIB) Bypass isolation breaker (BIB) Bypass Isolation Breaker for Module 1 (BIB1) Bypass isolation breaker for module 1 (BIB1) Bypass Isolation Breaker for Module 2 (BIB2) Bypass isolation breaker for module 2 (BIB2) Bypass Isolation Breaker for Module 3 (BIB3) Bypass isolation breaker for module 3 (BIB3) Bypass Isolation Breaker for Module 4 (BIB4) Bypass isolation breaker for module 4 (BIB4) Bypass Isolation Breaker for Module 5 (BIB5) Bypass isolation breaker for module 5 (BIB5) Bypass Isolation Breaker for Module 6 (BIB6) Bypass isolation breaker for module 6 (BIB6) Bypass Isolation Breaker for Module 7 (BIB7) Bypass isolation breaker for module 7 (BIB7) Bypass Isolation Breaker for Module 8 (BIB8) Bypass isolation breaker for module 8 (BIB8) Bypass Nominal Voltage Bypass nominal (or rated) voltage Bypass Not Available A problem associated with the bypass has been detected Bypass Overload Phase A An overload exists on output phase A while operating on the bypass Bypass Overload Phase B An overload exists on output phase B while operating on the bypass Bypass Overload Phase C An overload exists on output phase C while operating on the bypass Bypass Qualification Status bypass qualification status Bypass Retransfer Time Remaining Bypass SS Overload Time Remain Time remaining before an inverter overload or inverter fault can be cleared and auto retransfer from the bypass to the inverter can take place The calculated time remaining before bypass static switch shutdown due to the present overload condition Bypass Static Switch Off Extrnl Bypass static switch is off due to the state of an external signal Bypass Static Switch Overload Bypass off due to static switch overload Bypass Static Switch Unavailable The static bypass switch is off, and unable to operate
Page 1:
Infrastructure Management & Monitor
Page 4 and 5:
3.0 MODBUS 485 AND MODBUS IP PROTOC
Page 6 and 7:
3.4 Battery Monitoring Products . .
Page 8 and 9:
MODBUS 485 & MODBUS IP PROTOCOLS (c
Page 10 and 11:
2.3.2 Function Code 4 Modbus Commun
Page 12 and 13:
3.0 MODBUS 485 AND MODBUS IP PROTOC
Page 14 and 15:
Modbus 485 and Modbus IP Protocols
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Shutdown - Loss Of Power - Event Ty
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Remote Sensor System Average Over T
Page 38 and 39:
Page 40 and 41:
Table 10 Liebert CRV - Input and Ho
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Table 11 Liebert CRV - Glossary (co
Page 48 and 49:
Page 50 and 51:
Table 12 Liebert HPC (Chiller) - S
Page 52 and 53:
Table 13 Liebert HPC (Chiller) - In
Page 54 and 55:
Table 13 Liebert HPC (Chiller) - In
Page 56 and 57:
Table 14 Liebert HPC (Chiller) - Gl
Page 58 and 59:
Table 14 Liebert HPC (Chiller) - Gl
Page 60 and 61:
Table 15 Liebert XDC - Status and
Page 62 and 63:
Table 16 Liebert XDC - Input and Ho
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Table 17 Liebert XDC - Glossary (co
Page 74 and 75:
Table 17 Liebert XDC - Glossary (co
Page 76 and 77:
Page 78 and 79:
Table 19 Liebert XDP - Input and Ho
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Table 20 Liebert XDP - Glossary (co
Page 94 and 95:
Table 20 Liebert XDP - Glossary (co
Page 96 and 97:
Table 22 Liebert XDWP (XDP-W) - Inp
Page 98 and 99:
Table 23 Liebert DS and Liebert Pe
Page 100 and 101:
Table 24 Liebert DS and Liebert PeX
Page 102 and 103:
Table 24 Liebert DS and Liebert PeX
Page 104 and 105:
Table 26 Liebert XDF - Input and Ho
Page 106 and 107:
Page 108 and 109:
Table 29 Liebert DataMate, Liebert
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121: Modbus 485 and Modbus IP Protocols
Page 140 and 141: Table 40 Liebert APM - Status and
Page 142 and 143: Table 41 Liebert APM - Input and Ho
Page 144 and 145: Table 42 Liebert APM - Glossary (co
Page 146 and 147: 140 Modbus 485 and Modbus IP Protoc
Page 148 and 149: Table 44 Liebert GXT2 and Liebert G
Page 150 and 151: Table 47 Liebert Nfinity ® - Statu
Page 152 and 153: Table 49 Liebert NX - Status and C
Page 154 and 155: Table 50 Liebert NX - Input and Hol
Page 156 and 157: Table 51 Liebert NXL SA, SR, SN, M
Page 158 and 159: Table 52 Liebert NXL SA, SR, SN, MM
Page 182 and 183: Table 57 Liebert PowerSure Interact
Page 184 and 185: Table 59 Liebert Series 300 UPS - I
Page 186 and 187: Table 61 Liebert Series 600 UPS - I
Page 188 and 189: Table 63 Liebert Series 610 SCC UPS
Page 192 and 193: Table 65 Liebert SICE 7200 - Input
Page 194 and 195: Table 66 Liebert NPower - Input an
Page 196 and 197: Table 67 Liebert BDSU - Status and
Page 198 and 199: Table 68 Liebert BDSU - Input and H
Page 200 and 201: 4.0 BACNET COMMUNICATIONS BACnet Co
Page 202 and 203: 4.1.3 Standard Object Types Support
Page 204 and 205: BACnet Communications - BACnet Prot
Page 206 and 207: 4.2 Precision Cooling Products 200
Page 208 and 209: 202 BACnet Communications - Precisi
Page 220 and 221:
214 BACnet Communications - Precisi
Page 222 and 223:
Ext Standby Glycol Pump On - Event
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Table 73 Liebert CRV - Binary Data
Page 230 and 231:
Table 74 Liebert CRV - Analog Data
Page 232 and 233:
Table 74 Liebert CRV - Analog Data
Page 234 and 235:
Table 75 Liebert CRV - Multistate D
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Table 77 Liebert HPC - Binary Data
Page 244 and 245:
Table 77 Liebert HPC - Binary Data
Page 246 and 247:
Table 78 Liebert HPC - Analog Data
Page 248 and 249:
Table 79 Liebert HPC - Multistate D
Page 250 and 251:
Table 80 Liebert HPC - Glossary (co
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Table 82 Liebert XDP, Liebert XDWP
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Table 86 Liebert Mini-Mate2 8 Ton -
Page 274 and 275:
Table 87 Liebert APM - Binary Data
Page 276 and 277:
Table 88 Liebert APM - Analog Data
Page 278 and 279:
Table 90 Liebert APM - Glossary Dat
Page 280:
Ensuring The High Availability Of M
show all

Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?