Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP

More documents

Recommendations

Info

Table 14 Liebert HPC (Chiller) - Glossary Controller Liebert iCOM v4 Data Label Data Description Modbus 485 and Modbus IP Protocols - Precision Cooling Products Actual Supply Fluid Temp Set Point The actual set point value being used for the desired fluid temperature at the outlet of the unit. All Pumps Loss of Flow System is shut down due to loss of flow in all available pumps. Ambient Air Temperature Sensor Issue The ambient air temperature sensor is disconnected or the signal is out of range. Ambient Air Temperature Ambient air temperature. Compressor Capacity Control State Compressor capacity control state. When 'ON', the cooling capacity of the compressor has been reduced. Compressor Capacity Normal Compressor has returned to normal load capacity. Compressor Capacity Reduced Compressor capacity has been reduced. Compressor Contactor Issue Compressor contactor is not closing during compressor startup or is not opening during compressor shutdown. Compressor Economizer Utilization Present compressor economizer utilization expressed as a percentage of the maximum. Compressor Head Pressure Compressor head pressure. Compressor High Head Pressure Compressor is shut down due to high head pressure. Compressor Hours Exceeded [Compressor Hours] has exceeded [Compressor Hours Threshold]. Compressor Hours Threshold Threshold value used in the [Compressor Hours Exceeded] event. Compressor Hours Operating hours for compressor since last reset of this value. Compressor Loss of Differential Pressure Compressor is shut down due to low differential pressure. Compressor Low Oil Pressure Compressor low oil pressure. Compressor Low Suction Pressure Compressor is shut down due to low suction pressure. Compressor Not Stopping Compressor commanded to stop, but continues to run. Compressor Shut Down - Ambient Air Low Temp Limit Compressor State Compressor operational state. Compressor Superheat Over Threshold When the temperature of ambient air falls below this lower threshold, the compressor will be shut off. Correct condensing pressure cannot be achieved when temperature is too low. Compressor discharge refrigerant superheat temperature has exceeded an upper threshold. Compressor Thermal Overload Compressor is shut down due to thermal overload. Compressor Utilization Present compressor utilization expressed as a percentage of the maximum rated capacity. Condenser Adiabatic Cooling Utilization Present adiabatic cooling utilization expressed as a percentage of the maximum. Condenser Fan Issue Condenser fan is not operating within its operational parameters. Condenser Fan Speed Condenser fan speed expressed as a percentage of the maximum rated speed. Condenser Inlet Water Temperature Condenser Max Fan Speed Override Condenser Outlet Water Temperature Customer Input 1 Customer input 1. Customer Input 2 Customer input 2. Customer Input 3 Customer input 3. Customer Input 4 Customer input 4. For water cooled condensers, the temperature of the water entering the heat exchanger, before cooling the refrigerant. Fan speed exceeding the maximum set point in order to alleviate a high temperature or pressure condition. For water cooled condensers, the temperature of the water exiting the heat exchanger, after cooling the refrigerant. 50
Table 14 Liebert HPC (Chiller) - Glossary (continued) Controller Liebert iCOM v4 Data Label Data Description Evaporator Fluid Freeze - Auto Reset Evaporator Fluid Freeze - Manual Reset Required Evaporator Inlet Temp Sensor Issue Evaporator Return Fluid Over Temp Alarm Threshold Evaporator Return Fluid Over Temp Warning Threshold Evaporator Return Fluid Over Temp Evaporator Return Fluid Temperature Evaporator Return Fluid Under Temp Alarm Threshold Evaporator Return Fluid Under Temp Warning Threshold Evaporator Return Fluid Under Temp Modbus 485 and Modbus IP Protocols - Precision Cooling Products Evaporator outlet fluid temperature has dropped below the freeze threshold. Evaporator has been shut down, but will restart when the temperature rises above the threshold. Evaporator outlet fluid temperature has dropped below the freeze threshold. Evaporator has been shut down and requires a manual reset. The evaporator inlet temperature sensor is disconnected or the signal is out of range. Alarm threshold value used in the [Evaporator Return Fluid Over Temp] event. Warning threshold value used in the [Evaporator Return Fluid Over Temp] event. [Evaporator Return Fluid Temperature] has exceeded a threshold. The event is deactivated when the temperature drops below the threshold. Fluid temperature measured at the inlet of the evaporator. Alarm threshold value used in the [Evaporator Return Fluid Under Temp] event. Warning threshold value used in the [Evaporator Return Fluid Under Temp] event. [Evaporator Return Fluid Temperature] has dropped below a threshold. The event is deactivated when the temperature rises above the threshold. Fluid Cooling Proportional Band Temperature control band above [Actual Supply Fluid Temp Set Point]. If [Return Fluid Temperature] is within this band, fluid cooling operations are proportionally controlled. Fluid Pressure Fluid pressure. This is the pressure within a closed water/glycol circuit. Free Cooling External Temperature Delta Minimum temperature delta required between return fluid and external ambient air temperatures in order to enable free cooling. Free Cooling Status Free cooling status. Free Cooling Utilization Present free cooling utilization expressed as a percentage of the maximum. Free Cooling Valve Hours Exceeded [Free Cooling Valve Hours] has exceeded [Free Cooling Valve Hours Threshold]. Free Cooling Valve Hours Threshold Threshold value used in the [Free Cooling Valve Hours Exceeded] event. Free Cooling Valve Hours Operating hours for free cooling valve since last reset of this value. Free Cooling Valve Open Position Free cooling valve open position. Humidifier Control Board Not Detected Humidifier control board is required to be connected, but no signal is detected. Low Condenser Refrigerant Pressure Refrigerant pressure in condenser coil is too low. Low Fluid Pressure [Fluid Pressure] has dropped below a specified threshold. Master Unit Communication Lost Communication with master unit has been lost. Pump 1 Loss of Flow Loss of flow is detected in pump 1. This condition occurs when no flow is detected through the flow switch. Pump 1 State Pump 1 operational state. Pump 2 Loss of Flow Loss of flow is detected in pump 2. This condition occurs when no flow is detected through the flow switch. Pump 2 State Pump 2 operational state. Pump Hours Exceeded [Pump Hours] has exceeded [Pump Hours Threshold]. Pump Hours Threshold Threshold value used in the [Pump Hours Exceeded] event. Pump Hours Operating hours for pump since last reset of this value. RAM Battery Issue RAM or RAM backup battery is not operating correctly. 51
Page 1:
Infrastructure Management & Monitor
Page 4 and 5:
3.0 MODBUS 485 AND MODBUS IP PROTOC
Page 6 and 7: 3.4 Battery Monitoring Products . .
Page 8 and 9: MODBUS 485 & MODBUS IP PROTOCOLS (c
Page 10 and 11: 2.3.2 Function Code 4 Modbus Commun
Page 12 and 13: 3.0 MODBUS 485 AND MODBUS IP PROTOC
Page 14 and 15: Modbus 485 and Modbus IP Protocols
Page 22 and 23: Shutdown - Loss Of Power - Event Ty
Page 36 and 37: Remote Sensor System Average Over T
Page 40 and 41: Table 10 Liebert CRV - Input and Ho
Page 46 and 47: Table 11 Liebert CRV - Glossary (co
Page 48 and 49: Table 11 Liebert CRV - Glossary (co
Page 50 and 51: Table 12 Liebert HPC (Chiller) - S
Page 52 and 53: Table 13 Liebert HPC (Chiller) - In
Page 54 and 55: Table 13 Liebert HPC (Chiller) - In
Page 58 and 59: Table 14 Liebert HPC (Chiller) - Gl
Page 60 and 61: Table 15 Liebert XDC - Status and
Page 62 and 63: Table 16 Liebert XDC - Input and Ho
Page 72 and 73: Table 17 Liebert XDC - Glossary (co
Page 74 and 75: Table 17 Liebert XDC - Glossary (co
Page 78 and 79: Table 19 Liebert XDP - Input and Ho
Page 92 and 93: Table 20 Liebert XDP - Glossary (co
Page 94 and 95: Table 20 Liebert XDP - Glossary (co
Page 96 and 97: Table 22 Liebert XDWP (XDP-W) - Inp
Page 98 and 99: Table 23 Liebert DS and Liebert Pe
Page 100 and 101: Table 24 Liebert DS and Liebert PeX
Page 102 and 103: Table 24 Liebert DS and Liebert PeX
Page 104 and 105: Table 26 Liebert XDF - Input and Ho
Page 106 and 107:
Modbus 485 and Modbus IP Protocols
Page 108 and 109:
Table 29 Liebert DataMate, Liebert
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Table 40 Liebert APM - Status and
Page 142 and 143:
Table 41 Liebert APM - Input and Ho
Page 144 and 145:
Table 42 Liebert APM - Glossary (co
Page 146 and 147:
140 Modbus 485 and Modbus IP Protoc
Page 148 and 149:
Table 44 Liebert GXT2 and Liebert G
Page 150 and 151:
Table 47 Liebert Nfinity ® - Statu
Page 152 and 153:
Table 49 Liebert NX - Status and C
Page 154 and 155:
Table 50 Liebert NX - Input and Hol
Page 156 and 157:
Table 51 Liebert NXL SA, SR, SN, M
Page 158 and 159:
Table 52 Liebert NXL SA, SR, SN, MM
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Table 57 Liebert PowerSure Interact
Page 184 and 185:
Table 59 Liebert Series 300 UPS - I
Page 186 and 187:
Table 61 Liebert Series 600 UPS - I
Page 188 and 189:
Table 63 Liebert Series 610 SCC UPS
Page 190 and 191:
Page 192 and 193:
Table 65 Liebert SICE 7200 - Input
Page 194 and 195:
Table 66 Liebert NPower - Input an
Page 196 and 197:
Table 67 Liebert BDSU - Status and
Page 198 and 199:
Table 68 Liebert BDSU - Input and H
Page 200 and 201:
4.0 BACNET COMMUNICATIONS BACnet Co
Page 202 and 203:
4.1.3 Standard Object Types Support
Page 204 and 205:
BACnet Communications - BACnet Prot
Page 206 and 207:
4.2 Precision Cooling Products 200
Page 208 and 209:
202 BACnet Communications - Precisi
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Ext Standby Glycol Pump On - Event
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Table 73 Liebert CRV - Binary Data
Page 230 and 231:
Table 74 Liebert CRV - Analog Data
Page 232 and 233:
Table 74 Liebert CRV - Analog Data
Page 234 and 235:
Table 75 Liebert CRV - Multistate D
Page 236 and 237:
Table 76 Liebert CRV - Glossary (co
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Table 77 Liebert HPC - Binary Data
Page 244 and 245:
Table 77 Liebert HPC - Binary Data
Page 246 and 247:
Table 78 Liebert HPC - Analog Data
Page 248 and 249:
Table 79 Liebert HPC - Multistate D
Page 250 and 251:
Table 80 Liebert HPC - Glossary (co
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Table 82 Liebert XDP, Liebert XDWP
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Table 86 Liebert Mini-Mate2 8 Ton -
Page 274 and 275:
Table 87 Liebert APM - Binary Data
Page 276 and 277:
Table 88 Liebert APM - Analog Data
Page 278 and 279:
Table 90 Liebert APM - Glossary Dat
Page 280:
Ensuring The High Availability Of M
show all

Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?