Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP
Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP
Liebert® IntelliSlot® Modbus 485, Modbus IP and BACnet IP
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Table 11 Liebert CRV - Glossary<br />
Controller Liebert iCOM v4<br />
Data Description Description<br />
Air Temperature Control Sensor<br />
Air Temperature Dead B<strong>and</strong><br />
Air Temperature Set Point<br />
Auto Restart Delay<br />
BMS Communications Timeout<br />
<strong>Modbus</strong> <strong>485</strong> <strong>and</strong> <strong>Modbus</strong> <strong>IP</strong> Protocols - Precision Cooling Products<br />
Sensor from which air temperature measurements will be used for cooling <strong>and</strong><br />
heating control.<br />
Value that is divided evenly to form a temperature range above <strong>and</strong> below [Air<br />
Temperature Set Point]. If measured air temperature is within this range, no heating<br />
or cooling will occur.<br />
Desired air temperature. This set point is dependent upon which sensor is selected<br />
for control.<br />
If power is lost, the control will delay this amount of time after power is restored<br />
before restarting the unit.<br />
Building Management System (or external monitoring system) has not communicated<br />
with the system within the expected timeframe.<br />
BMS Timeout Period<br />
Timeframe within which the Building Management System (or external monitoring<br />
system) must communicate with the system to avoid a timeout.<br />
Bottom Fan Issue The bottom fan is not operating within its normal parameters.<br />
Calculated Next Maintenance Month<br />
Calculated Next Maintenance Year<br />
Calculated month of the next scheduled maintenance. Used in conjunction with<br />
[Calculated Next Maintenance Year].<br />
Calculated year of the next scheduled maintenance. Used in conjunction with<br />
[Calculated Next Maintenance Month].<br />
Chilled Water Control Valve Failure<br />
Chilled water valve out of position. Chilled water control valve position does not<br />
match expected value.<br />
Clogged Air Filter Air filter is dirty <strong>and</strong> needs to be (cleaned or) replaced.<br />
Compressor 1 High Head Pressure Compressor 1 high head pressure.<br />
Compressor 1 High Pressure<br />
Transducer Issue<br />
Compressor 1 high pressure transducer is disconnected or the signal is out of range.<br />
Compressor 1 Hours Exceeded Operating hours for compressor 1 have exceeded the threshold.<br />
Compressor 1 Low Pressure<br />
Transducer Issue<br />
Compressor 1 low pressure transducer is disconnected or the signal is out of range.<br />
Compressor 1 Low Suction Pressure Compressor 1 low suction pressure.<br />
Compressor 1 Pump Down Issue Unable to pump down suction-side pressure during compressor 1 shutdown.<br />
Compressor 1 Short Cycle<br />
Compressor 1 short cycle. A short cycle is defined as turning on <strong>and</strong> off a number of<br />
times over a set time period.<br />
Condenser 1 Issue Condenser 1 is not operating within its normal parameters.<br />
Condenser Control Board Issue The condenser control board is reporting an issue.<br />
Condenser Fan Issue Condenser fan is not operating within its operational parameters.<br />
Condenser Fan Power Condenser fan's measured input power.<br />
Condenser Fan Speed Condenser fan speed expressed as a percentage of the maximum rated speed.<br />
Condenser Low Noise Mode - Full<br />
Days<br />
Days of the week selected for low noise mode full day scheduling.<br />
Condenser Low Noise Mode -<br />
Interval Days<br />
Days of the week selected for low noise mode interval scheduling.<br />
Condenser Low Noise Mode Max<br />
Fan Speed<br />
Maximum fan speed when condenser is placed in low noise mode.<br />
Condenser Low Noise Mode<br />
Schedule Control<br />
Enable/disable scheduled control of condenser low noise mode.<br />
Condenser Low Noise Mode Start<br />
Time<br />
The time of day at which the condenser will transition into low noise mode.<br />
Condenser Low Noise Mode State State of condenser low noise mode scheduler control.<br />
Condenser Low Noise Mode Stop<br />
Time<br />
The time of day at which the condenser will transition out of low noise mode.<br />
Condenser Max Fan Speed Override<br />
Fan speed exceeding the maximum set point in order to alleviate a high temperature<br />
or pressure condition.<br />
39