Handbook of Turbomachinery Second Edition Revised - Ventech!

15. S. Lieblein, J. Basic Eng., Trans. ASME, Ser. D, 82: 575–587 (1960).
16. S. Lieblein, Basic Eng., Trans. ASME, Ser. D. 81: 387–400 (1959).
17. C. C. Koch and L. H. Smith, Jr., J. Eng. Power, Trans. ASME, Ser. A, 8: 411–
424 (1976).
18. W. C. Swan, J. Eng. Power, Trans. ASME, Ser. A, 83: 322–330 (1961).
19. O. E. Balje, Turbomachines, A Guide to Design, Selection and Theory, Chapter
4, John Wiley and Sons, New York (1981).
20. L. R. Reneau, J. P. Johnston, and S. Kline, ‘‘Performance and Design of
Straight Two-Dimensional Diffusers,’’ Thermosciences Division, Dept. of
Mechanical Engineering, Stanford University, Stanford, Calif., Report PD-8
(1964).
21. C. J. Sagi, J. P. Johnston, and S. J. Kline, Diffuser Design Manual, Part II. The
Design and Performance of Two-Dimensional Curved Diffusers, Thermosciences
Division, Dept. of Mechanical Engineering, Stanford University, Stanford,
Calif., Report PD-9 (1964).
22. R. O. Bullock, Aircraft Propulsion Systems Technology (G. C. Oates, ed.),
AIAA Education Series, American Institute of Aeronautics and Astronautics,
Inc., New York (1989).
23. D. P. Kenney, ‘‘A Novel Low Cost Diffuser for High Performance Centrifugal
Compressors,’’ ASME Paper 72-GT-54 (1972).
24. D. P. Kenney and R. E. Morris, ‘‘High Pressure Ratio Centrifugal
Compressors for Small Gas Turbine Engines.’’ Prepared for 31st Meeting of
the Propulsion and Energetics Panel of AGARD, Helicopter Propulsion
Systems, Ottawa, Canada, June 10–14 (1968).
25. W. F. O’Brien and K. M. Boyer, ‘‘Stall and Recovery in Multistage Axial
Compressors,’’ AGARD Conference Proceedings no. 468 (1990).
26. H. Starken and H. J. Lichtfuss, J. Eng. Power, Trans. ASME, Ser. A, 92: 267–
274 (1970).
27. P. R. Dodge, J. Eng. Power, Trans. ASME, Ser. A, 95: 185–190 (1973).
28. P. R. Dodge, ‘‘A Non-Orthogonal Numerical Method for Solving Transonic
Cascade Flows,’’ ASME Paper 76-GT-63 (1976).
29. J. T. Hamrick, A. Ginsberg, and W. M. Osborn, ‘‘Method of Analysis for
Compressible Flow Through Mixed-Flow Compressors of Arbitrary Design,’’
NACA Report 1082 (1952).
30. R. K. Novak and R. M. Hearsey, J. Fluids Eng. Trans. ASME, Ser. 1, 99: 154–
166 (1977).
31. C.-H. Wu, Z. Wang, and H. Chen, ‘‘Three-Dimensional Rotational Flow in
Transonic Turbomachines, Part 1, Solution Obtained Using a Number of S
Stream Filaments of Revolution and a Central S Stream Filament,’’ ASME
Paper 90-GT-18 (1990).
32. C.-H. Wu, X. Zhao, and D. L. Oin, ‘‘Three-Dimensional Rotational Flow in
Transonic Turbomachines, Part II, Full 3D Flow in CA#S Rotor Obtained
Using a Number of S and S Stream Filaments,’’ ASME Paper 90-GT-13 (1990).
33. T. Katsanis and W. D. McNally, ‘‘Revised Fortran Program for Calculating
Velocities and Streamlines on the Hub-Shroud Midchannel Stream Surface of
Copyright © 2003 Marcel Dekker, Inc.