2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
See pg. 337 See pg. 350 See pg. 362
VALVE
See pg. 360
VALVE
See pg. 306 See pg. 328 See pg. 312 See pg. 317
__ ALUMINUM ROCKERS __
AND RETAINER VALVE
STEM STEM
TIMING CHAIN AND GOLD
PRO SERIES
KITS SPRINGS RETAINERS SEALS LOCKS PUSHRODS GEAR ASSEMBLY RACE
STUD MOUNT
99832-16 c 99976-16 e 99818-16 g 99107-1 h 144986-1 *m 201759-16 *s
99832-16 c 99976-16 e 99818-16 g 99107-1 h 144986-1 *m 201759-16 *s
99832-16 c 99976-16 e 99818-16 g 99107-1 h 144986-1 *m 201759-16 *s
144311-1 b 144833-16 d 144661-16 f 99818-16 g 99108-1 i 144621-16 j 144984-1 *n 144750-16 p 201750-16 r
144622-16 k 144985-1 *o 144759-16 *q 201759-16 *s
95627-16 l
a For use with standard GM alignment bars, long travel design for up to .715”valve lift and reduced
base circle camshafts.
b Contains 144833-16 dual valve springs, 144661-16 titanium retainers, 144660-16 spring seats.
99818-16 valve seals, 99108-1 valve locks.
c Single ovate wire beehive valve springs, 1.450”dia., LS3 and L92 cylinder heads will require
machining
d Dual valve springs, requires Crane 144661-16 retainers, no machining required. 2002-up cylinder
heads will require Crane 144460-16 spring seats.
e Steel, requires Crane Multi Fit valve locks.
f Titanium, for 144833-16 dual valve springs.
g No machining required.
h Machined steel, heat treated, Multi Fit.
i Machined steel, heat treated.
j Pro Series one-piece, stock length.
k Pro Series one-piece, for use with Crane aluminum rocker arm kits (included in 201750-16 and
201759-16 kits).
99918-16 g 99108-1 i 144986-1 *m 201759-16 *s
201750-16 r
144311-1 b 144833-16 d 144661-16 f 99818-16 g 99108-1 i 144621-16 j 144984-1 *n 144750-16 p 201750-16 r
144622-16 k 144985-1 *o 144759-16 *q 201759-16 *s
95627-16 l
144311-1 b 144833-16 d 144661-16 f 99818-16 g 99108-1 i 144621-16 j 144984-1 *n 144750-16 p 201750-16 r
144622-16 k 144985-1 *o 144759-16 *q 201759-16 *s
95627-16 l
l Pro Series one piece, stock length -.050”.
m Pro Series steel billet gears and double roller chain set, three bolt, for LS7.
n Pro Series steel billet gears and roller chain set, with vernier adjustment (will not fit LS2).
o Pro Series steel billet gears and double roller chain set, three bolt, for LS2.
p 1.7 ratio, 3/8”stud, for LS1 type heads, complete kit includes rocker arms, adjusting nuts, pushrod
guideplates, rocker arm studs, and pushrods.
q 1.8 ratio, 3/8”stud, for LS1 type heads, complete kit includes rocker arms, adjusting nuts, pushrod
guideplates, rocker arm studs, and pushrods.
r 1.7 ratio, 3/8”stud, for L92 heads, complete kit includes rocker arms, adjusting nuts, pushrod
guideplates, rocker arm studs, and pushrods.
s 1.8 ratio, 3/8”stud, for L92 heads, complete kit includes rocker arms, adjusting nuts, pushrod
guideplates, rocker arm studs, and pushrods.
866-388-5120 • 386-236-9983 FAX 107