2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
STEEL
ROCKER
ARMS
See pg. 315 See pg. 317
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
99838-16 99953-16 99820-16 f 99097-1 i c 80975-1 *k 28774-16 *l 80757-16 n
99969-16 g 99094-1 j 80744-16 *m
99893-16 99953-16 99820-16 f 99097-1 i c 80975-1 *k 28774-16 *l 80757-16 n
99969-16 g 99094-1 j 80744-16 *m
99893-16 99953-16 99820-16 f 99097-1 i c 80975-1 *k 28774-16 *l 80757-16 n
99969-16 g 99094-1 j 80744-16 *m
99893-16 99953-16 99820-16 f 99097-1 i c 80975-1 *k 28774-16 *l 80757-16 n
99969-16 g 99094-1 j 80744-16 *m
11310-1 99838-16 99944-16 99820-16 f 99041-1 80975-1 *k 28774-16 *l 80757-16 n
99097-1 i
11310-1 99838-16 99944-16 99820-16 f 99041-1 80975-1 *k 28774-16 *l 80757-16 n
99097-1 i
99885-16 f 99678-16 h 99820-16 f 99097-1 i 80975-1 *k 28774-16 *l 80757-16 n
99885-16 f 99678-16 h 99820-16 f 99097-1 i 80975-1 *k 28774-16 *l 80757-16 n
99885-16 f 99678-16 h 99820-16 f 99097-1 i 80975-1 *k 28774-16 *l 80757-16 n
99885-16 f 99678-16 h 99820-16 f 99097-1 i 80975-1 *k 28774-16 *l 80757-16 n
a Camshaft incorporates an integral cast iron distributor drive gear, aluminum-bronze distributor
drive gear not required.
b Requires 80990-1 aluminum-bronze distributor drive gear.
c Vertical locking bar hydraulic roller lifters, no machining required. Special length pushrods are
required, see page 305 for special pushrod ordering instructions.
d Refer to chart on page 270 for correct application, requires appropriate Crane pushrods, see IMPOR-
TANT NOTE on opposite page.
e Ultra Pro Series roller lifters.
f Must machine cylinder heads.
g Requires Crane Multi Fit valve locks.
h Must use 99097-1 valve stem locks, included with the retainers.
i Machined steel, heat treated.
j Machined steel, heat treated, Multi Fit.
k Performance steel billet gears and roller chain set.
l Crane Classic extruded, 1.65 ratio, 7/16” stud, must machine cylinder heads and install 99157-16
rocker arms studs and aftermarket pushrod guideplates. Special heat treated pushrods are required
for use with pushrod guideplates.
m Energizer, 1.65 ratio, 3/8” stud, must machine cylinder heads and install 99156-16 rocker arm studs
and aftermarket pushrod guideplates. Special heat treated pushrods are required for use with
pushrod guideplates.
n 1.6 ratio, 7/16” stud, must machine cylinder heads and install 99157-16 rocker arm studs and
aftermarket pushrod guideplates. Special heat treated pushrods are required for use with pushrod
guideplates.
866-388-5120 • 386-236-9983 FAX 275