2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
STEEL
ROCKER
ARMS
See pg. 315 See pg. 317
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
96870-16 a 99969-16 b 99820-16 a 99094-1 c 52621-16 d 52975-1 *f 27774-16 g 27750-16 h
95650-16 e 27771-16 i
a Must machine cylinder heads.
b Requires appropriate Crane Multi Fit valve locks, see IMPORTANT NOTE for correct application.
c Machined steel, heat treated, Multi Fit 11/32” single groove type, see IMPORTANT NOTE for correct
application.
d For 70-74 351C, heavy wall, heat treated, for use with pushrod guideplate cylinder heads.
e Pro Series one piece, for 71-72 Boss 351, for use with pushrod guideplate cylinder heads.
f Performance steel billet gears and roller chain set.
g Crane Classic extruded, 1.72 ratio, requires 7/16” rocker arm studs and pushrod guideplates. See
notes on opposite page.
h 1.73 ratio, requires 7/16” rocker arm studs and pushrod guideplates. See notes on opposite page.
i 1.73 ratio Wide Body, requires 7/16” rocker arm studs and pushrod guideplates. See notes on opposite
page.
866-388-5120 • 386-236-9983 FAX 235