2011 - Crane Cams

More documents

Recommendations

Info

VALVE TRAIN Valve Spring Retainer Height Chart Retainer Height Chart To be able to achieve the proper valve spring height, while using the minimum amount of valve spring shims, can be challenging when working with applications that use other than stock components. There has never been an industry standard to compare the relationship of retainer heights with each other, although we have previously listed our retainer heights by comparing them with each other. This has been somewhat helpful if you have at least one of our retainers on hand for comparison purposes, but doesn’t properly address the variations of valve stem diameters, valve stem lock thicknesses, and taper angles. With this new listing, we are providing a measurable dimension that can be easily checked for the cylinder head and valve combination you’re working with. No sample retainers or fixtures are needed. The Retainer Height dimensions listed indicate the relationship of the outer step of the retainer that the outer valve spring sets against, with the top of the valve stem lock groove in the valve stem. If the dimension on the chart is .000”, the outer retainer step, and the top of the lock groove are at the same height. If the dimension is positive, such as .060”, then the outer retainer step is .060” above the top of the lock groove. If the dimension is negative, such as -.040”, then the outer spring step is .040” below the top of the lock groove. Check the accompanying drawings for a visual explanation. This will enable you to measure from the valve spring seat on the cylinder head, to the top of the lock groove in the valve, then compare that dimension to your desired valve spring assembly height (see the Valve Spring Retainer Dimension pages 350-351, and the Valve Spring to Retainer Cross Reference pages 355-357 for additional information). If you need an assembly height that’s .060” higher than your measured dimension, check the listings for the applicable retainers for your valve springs, and look for a height figure close to .060”. The standard height Crane Cams valve stem lock part numbers are listed with each diameter valve stem (where applicable) to achieve these figures. Remember, most of our valve stem locks are also available in +.050” and -.050” heights (see pages 360-361), to extend the available height combinations that can be created. The retainers are listed by material, then by lock configuration. The valve stems are listed by diameter and lock groove configuration. Certain unique specific retainers are listed using their usual valve locks, such as the Buick 11 degree, and the Ford Modular items. We hope this will make choosing your components easier, and provide a more reliable valve spring retainer/valve stem lock combination for your application. 352 CRANECAMS.COM
Valve Spring Retainer Height Chart Steel Retainers Retainer Part No. Valve Stem Diameter (Valve Stem Lock Part No.) 7° Crane Multi Fit and 3/8” 5/16 sq. 5/16 bead 11/32 sq. 11/32 bead 3/8 sq. 7mm bead 8mm bead 99093 99101 99094 99104 99098 99106 99107 99948 -.055 -.055 -.050 -.050 -.080 -.055 -.055 99950 .045 .045 .050 .050 .020 .045 .045 99954 .040 .040 .045 .045 .015 .040 .040 99955 .055 .055 .060 .060 .030 .055 .055 99957 .045 .045 .050 .050 .020 .045 .045 99961 .125 .125 .130 .130 .100 .125 .125 99962 .125 .125 .130 .130 .100 .125 .125 99964 .040 .040 .045 .045 .015 .040 .040 99969 .045 .045 .050 .050 .020 .045 .045 99970 .045 .045 050 .050 .020 .045 .045 99973 .110 .110 .115 .115 .085 .110 .110 99974 .110 .110 .115 .115 .085 .110 .110 99975 -.005 -.005 .000 .000 -.030 -.005 -.005 99976 7° Specific .010 .010 .015 .015 -.015 .010 .010 11/32 sq. 8mm bead 99097 99108 99914 .035 99915 .020 99916 -.055 99935 .075 99936 .005 99942 .285 99943 .135 99944 .075 99946 .075 99951 .135 99953 .135 99956 .125 99966 .135 99967 .215 144944 10° Crane Multi Fit -.030 5/16 sq. 11/32 sq. 3/8 sq. 99971 .030 .055 .045 99972 11° Specific .030 .055 .045 99912 11/32 Buick -.060 99910 3/8 Buick -.085 Section Continued 866-388-5120 • 386-236-9983 FAX 353
Page 1 and 2:
MASTER CATALOG CAMSHAF TS • VALVE
Page 3 and 4:
How to Use This Catalog About the C
Page 5 and 6:
Table of Contents Timing Chains and
Page 7 and 8:
Crane Cams History Crane Cams Histo
Page 9 and 10:
Camshaft Table of Contents Chrysler
Page 11 and 12:
Crane Camshaft Series Crane Camshaf
Page 13 and 14:
Crane Cams & Valve Train Products S
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Duration@ .050” Advertised Durati
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
*This product is applicable only to
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
1992-1996 305 (5.0L)- 350 (5.7L) LT
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Other sizes are available on reques
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
1986-1991 318 (5.2L) & 1987-1991 36
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Street roller camshafts are also of
Page 171 and 172:
Custom Grind Cams Also Available -
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Page 195 and 196:
1969-1993 351 (5.8L) cu.in. Windsor
Page 197 and 198:
Page 199 and 200:
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Page 209 and 210:
Page 211 and 212:
Page 213 and 214:
Page 215 and 216:
Page 217 and 218:
Page 219 and 220:
Page 221 and 222:
Page 223 and 224:
Page 225 and 226:
Page 227 and 228:
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Page 235 and 236:
Page 237 and 238:
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
nuts can be installed to permit ind
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Oldsmobile DRCE V8 The DRCE (Drag R
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Cam and Valve Train Buyer’s Guide
Page 287 and 288:
Camshaft Components Cam Degreeing B
Page 289 and 290:
Distributor-Magneto Drive Gears Cop
Page 291 and 292:
Distributor-Magneto Drive Gears Coa
Page 293 and 294:
Lifters - Hydraulic and Mechanical
Page 295 and 296:
Lifters - Hydraulic Roller Hydrauli
Page 297 and 298:
Lifters - Mechanical Roller Mechani
Page 299 and 300:
Lifters - Mechanical Roller Pushrod
Page 301 and 302: Lifters - Mechanical Roller Applica
Page 303 and 304: Lifters - Mechanical Roller Applica
Page 305 and 306: Lubricants Assembly Lube (Paste) Cr
Page 307 and 308: Pushrods Overall Ends Application C
Page 309 and 310: Pushrods - One Piece Pro Series, On
Page 311 and 312: Pushrod Accessories Pushrod Guidepl
Page 313 and 314: Rocker Arms, Steel & Ductile Iron A
Page 315 and 316: Aluminum Rocker Arms, Energizer Ene
Page 317 and 318: Aluminum Roller Rockers, Gold Race
Page 319 and 320: Aluminum Roller Rockers, Gold Race
Page 321 and 322: Aluminum Shaft Mount Rocker Arms Ne
Page 323 and 324: Rocker Arm Adjusting Nuts, Screws R
Page 325 and 326: Rocker Arm Guideplate Conversion Ki
Page 327 and 328: Rocker Arm Studs Rocker Arm Studs C
Page 329 and 330: Timing Chains and Components Pro-Se
Page 331 and 332: Tools Pushrods, Adjustable Checking
Page 333 and 334: Vacuum Kits and Accessories Adjusta
Page 335 and 336: Valve Train Questions Valve Spring
Page 337 and 338: Valve Springs O.D I.D. Damper Seat
Page 339 and 340: Valve Springs O.D I.D.1 I.D.2 Dampe
Page 341 and 342: Valve Springs Valve Spring Spec Cha
Page 349 and 350: Valve Spring Retainers How to Use t
Page 351: Valve Spring Retainer Dimensions -
Page 355 and 356: Valve Spring to Retainer Cross Refe
Page 357 and 358: Valve Spring to Retainer Cross Refe
Page 359 and 360: Valve Spring and Retainer Kits Valv
Page 361 and 362: Valve Stem Locks Multi-Fit Valve St
Page 363 and 364: Valve Train Stabilizers Durable ste
Page 365 and 366: How to Identify Your Crane Cam SERI
Page 367 and 368: Street/Strip, Off Road, Marine Cams
Page 369 and 370: Finish Grind Crane Round Lobe Outri
Page 371 and 372: Other Engine Applications Ford, Lin
Page 373 and 374: Flat Tappet Camshaft Break-in Proce
Page 375 and 376: Adjusting the Valve Train Hydraulic
Page 377 and 378: Commonly Asked Valve Spring Questio
Page 379 and 380: Cam and Valve Train Questions Commo
Page 381 and 382: Degreeing the Cam Degreeing the Cam
Page 383 and 384: Degreeing the Cam Degreeing the Cam
Page 385 and 386: Understanding the Cam Specification
Page 387 and 388: Ignition Table of Contents HI-6S Mu
Page 389 and 390: Street Performance, Trucks, Trailer
Page 391 and 392: Street, Street Performance, Race HI
Page 393 and 394: Street Performance, Race HI-6R/Digi
Page 395 and 396: Street Performance, Race, Turbo HI-
Page 397 and 398: Street Performance, Race, Turbo HI-
Page 399 and 400: Oval Track, Race HI-6N CD Ignition
Page 401 and 402: Timing Retard Timing Retard Control
Page 403 and 404:
Points Conversion Ignition XR-i Poi
Page 405 and 406:
Points Conversion Ignition XR700 Re
Page 407 and 408:
Points Conversion Ignition XR3000 R
Page 409 and 410:
Distributors Race Billet Distributo
Page 411 and 412:
Distributors Oval Track Pro Race Di
Page 413 and 414:
Performance Ignition Coils LX91, LX
Page 415 and 416:
Performance Ignition Coils PS91, PS
Page 417 and 418:
Performance Plug Wires 8.5mm Fire W
Page 419 and 420:
FireWire Spark Plug Wire Now Availa
Page 421 and 422:
Part Number Index Part No. Page No.
Page 423 and 424:
Page 425 and 426:
Page 427 and 428:
Page 429 and 430:
Page 431 and 432:
Page 433 and 434:
show all

2011 - Crane Cams

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?