2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
CAST
ROCKER
ARMS
See pg. 315 See pg. 321
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
99896-16 d 99970-16 f 99822-16 d 99099-1 i j 34772-16 p 34791-1 q
99832-16 e 99976-16 g 95805-16 k
99896-16 d 99970-16 f 99822-16 d 99099-1 i j 34772-16 p 34791-1 q
99832-16 e 99976-16 g 95805-16 k
99896-16 d 99970-16 f 99822-16 d 99099-1 i j 34772-16 p 34791-1 q
99832-16 e 99976-16 g 95805-16 k
99896-16 d 99970-16 f 99822-16 d 99099-1 i j 34772-16 p 34791-1 q
99832-16 e 99976-16 g 95805-16 k
99896-16 d 99970-16 f 99822-16 d 99099-1 i j 34772-16 p 34791-1 q
99832-16 e 99976-16 g 95805-16 k
96877-16 d 99969-16 h 99822-16 d 99098-1 i 34621-16 l 34772-16 p 34791-1 q
34622-16 m
95819-16 n
95847-16 o
96877-16 d 99969-16 h 99822-16 d 99098-1 i 34621-16 l 34772-16 p 34791-1 q
34622-16 m
95819-16 n
95847-16 o
96877-16 d 99969-16 h 99822-16 d 99098-1 i 34621-16 l 34772-16 p 34791-1 q
34622-16 m
95819-16 n
95847-16 o
96877-16 d 99969-16 h 99822-16 d 99098-1 i 34621-16 l 34772-16 p 34791-1 q
34622-16 m
95819-16 n
95847-16 o
96877-16 d 99969-16 h 99822-16 d 99098-1 i 34621-16 l 34772-16 p 34791-1 q
34622-16 m
95819-16 n
95847-16 o
a Requires 34970-1 (.467” I.D.) steel, or 34990-1 (.467” I.D.) aluminum-bronze distributor drive gear,
and 7/16-14 x 1-1/8” grade 8 cam gear bolt and hardened washer.
b Vertical locking bar hydraulic roller lifters, no machining required. Special length pushrods are
required, refer to page 305 for special pushrod ordering instructions.
c Shell-type lifters, requires 34622-16 pushrods for 34772-16 rocker arms, or 95847-16 pushrods
for 34791-1 rocker arms.
d Must machine cylinder heads.
e Ovate wire beehive spring, requires 99976-16 retainers.
f Requires 99099-1 valve locks.
g Steel, for 99832-16 beehive springs.
h Requires 99098-1 valve locks.
i Machined steel, heat treated.
j Special length pushrods are required for standard non-adjustable or 34772-16 adjustable rocker
arms. See page 305 for special pushrod ordering instructions.
k For use with 34791-1 adjustable rocker arms with cup type adjusters.
l Heavy wall, heat treated, for use with 99257-16 lifters and 34772-16 adjustable rocker arms.
m Heavy wall, heat treated, for use with 99256-16 lifters and 34772-16 adjustable rocker arms.
n Pro Series one-piece, for use with 99257-16 lifters and 34791-1 adjustable rocker arms with cup
type adjusters.
o Pro Series one-piece, for use with 99256-16 lifters and 34791-1 adjustable rocker arms with cup
type adjusters.
p 1.76 ratio, ductile iron, adjustable, requires appropriate Crane pushrods.
q 1.76 ratio, with cup type adjusters, complete with shafts, stands, and hardware. For low rise and
Edelbrock cylinder heads, requires appropriate Crane pushrods.
866-388-5120 • 386-236-9983 FAX 247