2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
11310-1 99838-16 99944-16 99820-16 f 99041-1 95654-16 i 28975-1 *l 28774-16 *m 28750-16 n
99097-1 g 28624-16 j 28758-16 *o
95663-16 k
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
STEEL
ROCKER
ARMS
See pg. 315 See pg. 317
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
11310-1 99838-16 99944-16 99820-16 f 99041-1 95654-16 i 28975-1 *l 28774-16 *m 28750-16 n
99097-1 g 28624-16 j 28758-16 *o
95663-16 k
11310-1 99838-16 99944-16 99820-16 f 99041-1 95654-16 i 28975-1 *l 28774-16 *m 28750-16 n
99097-1 g 28624-16 j 28758-16 *o
95663-16 k
11310-1 99838-16 99944-16 99820-16 f 99041-1 95654-16 i 28975-1 *l 28774-16 *m 28750-16 n
99097-1 g 28624-16 j 28758-16 *o
95663-16 k
11310-1 99838-16 99944-16 99820-16 f 99041-1 95654-16 i 28975-1 *l 28774-16 *m 28750-16 n
99097-1 g 28624-16 j 28758-16 *o
95663-16 k
96870-16 99973-16 e 99820-16 f 99094-1 h 28624-16 j 28975-1 *l 28774-16 *m 28750-16 n
95663-16 k 28758-16 *o
96870-16 99973-16 e 99820-16 f 99094-1 h 28624-16 j 28975-1 *l 28774-16 *m 28750-16 n
95663-16 k 28758-16 *o
96870-16 99973-16 e 99820-16 f 99094-1 h 28624-16 j 28975-1 *l 28774-16 *m 28750-16 n
95663-16 k 28758-16 *o
96870-16 99973-16 e 99820-16 f 99094-1 h 28624-16 j 28975-1 *l 28774-16 *m 28750-16 n
95663-16 k 28758-16 *o
99896-16 d 99974-16 e 99820-16 f 99094-1 h 28624-16 j 28975-1 *l 28774-16 *m 28750-16 n
95663-16 k 28758-16 *o
a Camshaft incorporates an integral cast iron distributor drive gear, aluminum-bronze distributor drive
gear not required. Not for use in 265 and 301 engines.
b Requires 28990-1 aluminum-bronze distributor drive gear. Not for use in 265 and 301 engines.
c Due to block casting variations, you must check that the lifter relief band is not exposed at the bottom
of the lifter bore when the lifter is on the base circle of the camshaft.
d Ultra Pro Series roller lifters.
e Requires Crane Multi Fit valve locks.
f Must machine cylinder heads.
g Machined steel, heat treated.
h Machined steel, heat treated, Multi Fit.
i Pro Series one-piece, for non-guideplate cylinder heads.
j Heavy wall, heat treated, for use with pushrod guideplate cylinder heads.
k Pro Series one piece for use with or without pushrod guideplate cylinder heads.
l Performance steel billet gears and roller chain set.
m Crane Classic extruded 1.65 ratio, for straight 7/16” studs.
n 1.5 ratio, for 7/16” bottleneck studs and 3/8” nuts.
o 1.65 ratio, for straight 7/16” studs.
866-388-5120 • 386-236-9983 FAX 281