2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
CAST
ROCKER
ARMS
See pg. 315 See pg. 321
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
99893-16 99954-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
99832-16 c 99976-16 f 95818-16 k
99893-16 99954-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
99832-16 c 99976-16 f 95818-16 k
96886-16 d 99955-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
95818-16 k
96886-16 d 99955-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
95818-16 k
96886-16 d 99955-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
95818-16 k
96886-16 d 99955-16 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
95818-16 k
96880-16 d 99679-16 g 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
961246-16 e 99662-16 h 95818-16 k
96880-16 d 99679-16 g 99822-16 d 99098-1 i 34641-16 j 34772-16 l 34791-1 m
961246-16 e 99662-16 h 95818-16 k
a Requires 34970-1 (.467” I.D.) steel, or 34990-1 (.467” I.D.) aluminum-bronze distributor drive gear,
and 7/16-14 x 1-1/8” grade 8 cam gear bolt and hardened washer.
b Ultra Pro Series roller lifters.
c Ovate wire beehive spring, requires 99976-16 retainers.
d Must machine cylinder heads.
e Triple, for 2.050” assembly height, requires 99662-16 titanium retainers.
f Steel for 99832-16 beehive springs.
g Must use 99098-1 valve stem locks, included with the retainers.
h Titanium, for 961246-16 valve springs.
i Machined steel, heat treated.
j For use with 34772-16 adjustable rocker arms, heavy wall, heat treated.
k Pro Series one-piece, for use with 34791-1 adjustable rocker arms with cup type adjusters.
l 1.76 ratio, ductile iron, adjustable, requires appropriate 34641-16 Crane pushrods.
m 1.76 ratio, with cup type adjusters, complete with shafts, stands, and hardware. For low rise and
Edelbrock cylinder heads, requires appropriate 95818-16 Crane pushrods.
866-388-5120 • 386-236-9983 FAX 249