2011 - Crane Cams

*This product is applicable only to pre-1966 California and pre-1968 federally certified passenger cars. It
is also applicable to non-emission controlled trucks and similar vehicles. It is not applicable or intended
for use on any emission controlled vehicles operated on highways or roads.
Custom Grind Cams Also Available – Call 866-388-5120 or go to cranecams.com for ordering information
CRANE VALVE TRAIN COMPONENTS
See pg. 358
VALVE SPRING
AND RETAINER
KITS
See pg. 337
VALVE
SPRINGS
See pg. 350
RETAINERS
See pg. 362
VALVE
STEM
SEALS
See pg. 360
VALVE
STEM
LOCKS
See pg. 306
PUSHRODS
See pg. 328
TIMING CHAIN
AND GEAR
ASSEMBLY
See pg. 312
STEEL
ROCKER
ARMS
See pg. 315 See pg. 317
__ ALUMINUM ROCKERS __
CRANE CLASSIC/ GOLD
ENERGIZER RACE
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 11630-16 l 11984-1 *n 11771-16 p
99087-1 k 95636-16 m 11977-1 *o
99885-16 e,f 99956-16 99820-16 e 99097-1 j 11630-16 l 11984-1 *n 11750-16 q
96883-16 e,g 99675-16 h 99087-1 k 95636-16 m 11977-1 *o 11771-16 p
99970-16 i
99885-16 e,f 99956-16 99820-16 e 99097-1 j 95636-16 m 11984-1 *n 11771-16 p
96883-16 e,g 99675-16 h 99087-1 k 11977-1 *o
99970-16 i
99885-16 e,f 99956-16 99820-16 e 99097-1 j 11630-16 l 11984-1 *n 11771-16 p
96883-16 e,g 99675-16 h 99087-1 k 95636-16 m 11977-1 *o
99970-16 i
99885-16 e,f 99956-16 99820-16 e 99097-1 j 11630-16 l 11984-1 *n 11750-16 q
96883-16 e,g 99675-16 h 99087-1 k 95636-16 m 11977-1 *o 11771-16 p
99970-16 i
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 11630-16 l 11984-1 *n 11771-16 p
95636-16 m 11977-1 *o
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 95636-16 m 11984-1 *n 11771-16 p
11977-1 *o
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 95636-16 m 11984-1 *n 11771-16 p
11977-1 *o
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 95636-16 m 11984-1 *n 11771-16 p
11977-1 *o
99880-16 e,f 99675-16 h 99820-16 e 99097-1 j 95636-16 m 11984-1 *n 11771-16 p
11977-1 *o
a Requires cam button spacer and a 11990-1 (.489”I.D.) or 11989-1 (.500”I.D. Accel) aluminumbronze
distributor drive gear. For engines equipped with mechanical fuel pumps, fuel pump
pushrod 11985-1 is highly recommended to prevent fuel pump lobe wear.
b Camshaft has SFO firing order, with 4/7 swap.
c Ultra Pro Series vertical locking bar roller lifters.
d Ultra Pro Series vertical locking bar roller lifters for .904”diameter lifter bores.
e Must machine cylinder heads.
f For cylinder heads with +.100”long valves.
g For cylinder heads with +.100”long valves, use 99970-16 retainers and 99087-1 valve stem locks.
h Titanium, must use 99097-1 valve stem locks, included with the retainers.
i Requires Crane Multi Fit valve locks.
j Machined steel, heat treated.
k Machined steel, heat treated, Multi Fit.
l Heavy wall, heat treated, for use with or without pushrod guideplate cylinder heads.
m Pro Series one-piece, for use with or without pushrod guideplate cylinder heads.
n Pro Series steel billet gears and roller chain set.
o Pro Series steel billet gears and roller chain set with thrust bearing.
p 1.5 ratio, 7/16”stud (not self-aligning),Wide Body.ValveTrain Stabilizer available, see page 363.
q 1.5 ratio, 3/8”stud (not self-aligning).ValveTrain Stabilizer available, see page 363.
866-388-5120 • 386-236-9983 FAX 87