SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

Recommendations

Info

SonTek/YSI 98 Figure A2.6. Argonaut to SDI-12 interface cable (dwg 8004-30000). Older cable: Drains as SDI-12 control line; 7 conductors & a drain. Figure A2.7. Argonaut to SDI-12 interface cable (dwg 8004-40000). Older cable: Drain as ground, black as SDI-12 control; 7 conductors and a drain. Argonaut Operation Manual Firmware Version 7.9 (May 1, 2001)
A2.3. Setting Up the Argonaut for Data Collection Argonaut Operation Manual Firmware Version 7.9 (May 1, 2001) SonTek/YSI Connect the Argonaut to a computer and power as described above. The commands to set up the Argonaut operation parameters are only accessible when the system is in the RS-232 mode. To put the Argonaut into RS-232 mode, connect the RS-SDI switching plug (Figure A2.2). On your PC, run either SonTerm or SonTermW. Within SonTerm, send an Argonaut BREAK (by entering Alt+B or +++) to wake-up the Argonaut. Note: If you receive a response after the BREAK similar to “The system is in SDI-12 mode…”, you must type ?EXIT! to return to RS-232 mode. After communication has been established, verify that the Argonaut has the SDI-12 option installed and view its system address by entering the following command ( = Enter key). >sdi12address If the SDI-12 option is enabled, the Argonaut will return the address being used: Current Sdi12 address: 1. If the SDI12 option is not enabled, the following error message is returned: ERROR: System does not have SDI-12 Interface installed. SDI-12 commands are disabled To change the Argonaut SDI-12 address, send the following command >sdi12address 2 where “2” is the desired SDI-12 address (acceptable addresses: “0-9”, “A-Z”, or “a-z”). If more than one sensor is to be connected to the SDI-12 bus, make certain each sensor has a unique sensor address. The Averaging Interval (AI) is the period, in seconds, over which the Argonaut averages the data before computing mean velocity. This value also determines how long the SDI-12 measurement will take to complete. The Sampling Interval (SI) is irrelevant with the use of the Single-Sample mode to initiate a measurement. However, for command consistency you should set SI to a value equal to or greater than AI. When using an Argonaut as an SDI-12 sensor, do not set AI to more than 992 seconds (16.6 minutes). This limitation is necessary because the SDI-12 protocol only supports measurement intervals up to 999 seconds. The values shown in the following example will cause the Argonaut to measure and average flow data for a period of 60 seconds. Configure the regular operating parameters of the Argonaut for your application using the direct command interface described in Section 3 of this manual. As an example: To set Cell Begin (CB) to 0.5 m and Cell End (CE) to 15.0 m use the following. Note: To determine actual CB and CE values, use ArgCheck (see Argonaut Software Manual). >CB 0.5 >CE 15.0 To set averaging and sampling intervals to 30 s use: >AI 30 >SI 30 To set output mode to AUTO use: >OM AUTO To set output format to ENGLISH use: >OF ENGLISH 99
Page 1 and 2:
Argonaut SL / SW / XR Firmware Vers
Page 3 and 4:
2. Installing the Firmware Update A
Page 5 and 6:
SonTek/YSI 1.3. Assorted Changes Th
Page 7:
A YSI Environmental Company SonTek/
Page 10 and 11:
SonTek 2 • Click Realtime to star
Page 13 and 14:
WARRANTY, TERMS AND CONDITIONS Argo
Page 15 and 16:
TABLE OF CONTENTS Argonaut Operatio
Page 17 and 18:
Argonaut Operation Manual Firmware
Page 19 and 20:
Section 1. Argonaut Components, Ter
Page 21 and 22:
Page 23 and 24:
Section 2. Getting Started Argonaut
Page 25 and 26:
Section 3. Direct Command Interface
Page 27 and 28:
3.2.4. Sleep Mode Argonaut Operatio
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
3.7. System Commands System command
Page 35 and 36:
OutFormat or OF [BINARY|ASCII|SEABI
Page 37 and 38:
Page 39 and 40:
• Parameter range: 0.4 to 10 mete
Page 41 and 42:
AvgInterval or AI [d] • See descr
Page 43 and 44:
3.11. Recorder Commands Recorder co
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
3.15. Run-Time Commands This sectio
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Section 4. Compass/Tilt Sensor Oper
Page 59 and 60:
system will change depending on whe
Page 61 and 62:
Page 63 and 64:
Page 65 and 66: Section 5. Argonaut Hardware 5.1. A
Page 67 and 68: Argonaut Operation Manual Firmware
Page 69 and 70: 5.3. Argonaut Processor Argonaut Op
Page 71 and 72: 5.4. Communication Baud Rate Settin
Page 73 and 74: 8-pin UWM Male IL-8-MP to Argonaut
Page 79 and 80: Section 6. Operational Consideratio
Page 85 and 86: XYZ coordinate system Argonaut Oper
Page 89 and 90: 6.8. Troubleshooting Argonaut Opera
Page 91 and 92: 6.9. Protection from Biological Fou
Page 93 and 94: Section 7. Autonomous Deployment 7.
Page 95 and 96: 7.3. Starting an Autonomous Deploym
Page 97 and 98: Section 8. Argonaut Optional Featur
Page 99 and 100: 8.2. Pressure Series Data Conversio
Page 101 and 102: 8.3.2. CTD ASCII Data Format Argona
Page 103 and 104: Section 9. Additional Support Argon
Page 105 and 106: Appendix 1. Argonaut Binary Data Fi
Page 109 and 110: A1.4. Checksum Calculation Argonaut
Page 111 and 112: Appendix 2. Internal SDI-12 Support
Page 115: Figure A2.4. Argonaut to SDI-12 int
Page 119 and 120: A2.4. Summary of Argonaut SDI-12 Co
Page 121 and 122: A2.5. SDI-12 Command and Response P
Page 123 and 124: A2.5.2. Concurrent Measurement Comm
Page 125 and 126: Where: Data Format Metric English x
Page 127 and 128: A2.5.7. Send Identification Command
Page 129 and 130: Appendix 3. Vertical Beam Support f
Page 131 and 132: Appendix 4. Analog Output Option fo
Page 133 and 134: A4.3. Configuring the Serial-to-AO
Page 135 and 136: A4.4. Configuring the Argonaut-SL/X
Page 137 and 138: ? ?EXIT! command, 24 + +++ (alterna
Page 139 and 140: measurement volume, 2 METRIC output
Page 141 and 142: SonTek/YSI 6837 Nancy Ridge Drive,
Page 143 and 144: TABLE OF CONTENTS SonTek/YSI Sectio
Page 145 and 146: Section 1. Software Summary SonTek/
Page 147 and 148: Section 2. Software Installation So
Page 149 and 150: Section 3. ViewArgonaut Windows Sof
Page 151 and 152: SonTek/YSI 3.3. SonRec Recorder Dat
Page 153 and 154: 3.4. Deployment Upon execution, the
Page 155 and 156: The basic procedure for an autonomo
Page 157 and 158: SonTek/YSI Averaging Interval • T
Page 159 and 160: 3.4.2. SDI-12 Deployment Setup Para
Page 161 and 162: SonTek/YSI Averaging Interval • T
Page 163 and 164: 3.5.1. Real-time User Setup Window
Page 165 and 166: SonTek/YSI Cell Begin / Cell End
Page 167 and 168:
SonTek/YSI Active Menu Buttons The
Page 169 and 170:
3.5.3. Data Recording The real-time
Page 171 and 172:
Velocity Plot SonTek/YSI • The ve
Page 173 and 174:
Open File Copy Screen Print Screen
Page 175 and 176:
SonTek/YSI PostProcessing Functions
Page 177 and 178:
Two types of data files can be expo
Page 179 and 180:
Section 4. SonUtils Windows Softwar
Page 181 and 182:
The SonTermW window is divided into
Page 183 and 184:
The CompCalW window is divided into
Page 185 and 186:
The SonRecW window is divided into
Page 187 and 188:
SonTek/YSI Section 5. Real-Time Dat
Page 189 and 190:
SonTek/YSI For example, the followi
Page 191 and 192:
SonTek/YSI simplify post-processing
Page 193 and 194:
SonTek/YSI Tabular Data The tabular
Page 195 and 196:
SonTek/YSI record containing time,
Page 197 and 198:
Section 6. GARG*/EARG* Data Extract
Page 199 and 200:
SonTek/YSI Signal strength data is
Page 201 and 202:
SonTek/YSI The program generates ta
Page 203 and 204:
SonTek/YSI Section 7. Deployment Su
Page 205 and 206:
Figure 17 - ARGCHECK Output - Near
Page 207 and 208:
SonTek/YSI When looking at the ARGC
Page 209 and 210:
Section 9. Terminal Emulation with
Page 211 and 212:
Section 10. Recorder Data Extractio
Page 213 and 214:
Section 11. Additional Support SonT
Page 215 and 216:
Appendix 1. Automatic File Naming C
Page 217 and 218:
Index A ARG.LOG, 51 ArgCheck [ViewA
Page 219 and 220:
Argonaut Principles of Operation 68
Page 221 and 222:
1. Introduction Argonaut Principles
Page 223 and 224:
Argonaut Principles of Operation (M
Page 225 and 226:
Page 227 and 228:
5.4. Percent Good Argonaut Principl
Page 229 and 230:
Page 231 and 232:
Index A accuracy, 8 along-beam velo
Page 233 and 234:
Using Frequency Pressure Sensors wi
Page 235 and 236:
3.2. The Paroscientific Digiquartz
Page 237 and 238:
Show DRUCK or Show PAROSFREQ • Di
Page 239 and 240:
5.2. PC-ADP Header Extraction: GADP
show all

SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?