SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West
SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West
SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
<strong>SonTek</strong>/<strong>YSI</strong><br />
To set SDI-12 SIDEKICK format use (you may also use SONTEK in firmware v7.9 or later):<br />
>sdi12format SIDEKICK <br />
If you need the data to be stored on the <strong>Argonaut</strong>’s internal recorder (in addition to being logged<br />
onto an SDI-12 data-logger), turn the recorder ON using:<br />
>recorder on <br />
After setup is complete, save your settings using:<br />
>savesetup <br />
To put the <strong>Argonaut</strong> into SDI-12 data collection mode use:<br />
>SDI12 ON <br />
The <strong>Argonaut</strong> sends this reply to indicate it is now in SDI-12 mode (see Important Notes #1):<br />
OK<br />
Checking Setup Parameters...<br />
917504 free bytes left in recorder.<br />
Free space is sufficient for 2.31 days of operation.<br />
Recorder mode is NORMAL.<br />
Switching to SDI-12 mode<br />
SDI-12 address is: 1<br />
You should verify that the <strong>Argonaut</strong> can now accept SDI-12 commands by sending the following<br />
SDI-12 “Send Identification” command and receiving the appropriate response (§A2.5.7).<br />
?I! (You may be required to enter a also; see Important Notes #2 first.)<br />
112 <strong>SonTek</strong> SL 79 E272<br />
You can now enter additional SDI-12 commands. When done, make sure you disconnect the RS-<br />
SDI switching plug (Figure A2.6) to complete the process of placing <strong>Argonaut</strong> in SDI-12 mode.<br />
Important Notes:<br />
1. If the recorder is enabled and already full, the <strong>Argonaut</strong> responds with an error message and<br />
will not enter SDI-12 mode. To proceed, the recorder has to be either disabled or formatted.<br />
2. Depending on the terminal emulator you are using (SonTerm [for DOS] or SonTermW [for<br />
Windows]), you may be required to enter a to complete the command string.<br />
• SonTerm (for DOS) – Do not enter the terminating . The system recognizes the “!”<br />
character as the command terminator. If you inadvertently send a , you can return<br />
the system to a known state by sending a BREAK, or any other valid SDI-12 command not<br />
followed by a .<br />
• SonTermW (for Windows) – You do enter the terminating , assuming you have set<br />
the File|Communications Mode to SDI-12. If this item is set to RS232/422/485, the system<br />
will act the same as SonTerm for DOS (as described above).<br />
3. If a BREAK is issued to an <strong>Argonaut</strong> that is in SDI-12 mode, the system will not stop its<br />
operation and will send the following message.<br />
100<br />
112 <strong>SonTek</strong> SL 79 E272<br />
System is in SDI-12 mode. To switch to RS232 type ?EXIT!<br />
4. While in SDI-12 mode, the serial communications do not support full duplex. Therefore, the<br />
characters you enter are not echoed back to the screen.<br />
<strong>Argonaut</strong> Operation <strong>Manual</strong> Firmware Version 7.9 (May 1, 2001)