SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

Recommendations

Info

SonTek/YSI 14 • A 3-digit termination is added to the specified file name, starting with 001 and incrementing (002, 003, …) each time data collection is stopped and started. • The file names use the extension .ARG. For example, if the file name is TEST, the first file will be TEST001.ARG, followed by TEST002,ARG, etc. Start Date and Time • This specifies the starting date and time for the first sample in the deployment. • If the current date and time is after the specified start date and time, the deployment will start immediately. • All dates and times are based on the internal Argonaut clock. Burst Mode • This enables or disables burst sampling mode. • Burst sampling is not commonly used; this parameter is typically DISABLED. • See the Argonaut Operation Manual for a description of burst sampling. Burst Interval • When burst-sampling mode is enabled, this sets the time from the start of one burst to the start of the next burst. • This parameter can only be modified when burst sampling is enabled. • See the Argonaut Operation Manual for a description of burst sampling. Samples Per Burst • When burst-sampling mode is enabled, this sets the number of samples per burst. • This parameter can only be modified when burst sampling is enabled. • See the Argonaut Operation Manual for a description of burst sampling. Comment 1/2/3 • Up to three comment lines are provided for you to document the data set. Argonaut Software Manual (March 1, 2001)
3.4.2. SDI-12 Deployment Setup Parameters Hardware Configuration Window Deployment Button Figure 5 – ViewArgonaut SDI-12 Deployment Setup Window Figure 5 shows the SDI-12 deployment setup window. • The main area lists setup parameters. • The bottom has the control buttons. The basic procedure for an SDI-12 deployment is below. SonTek/YSI • Connect the Argonaut to the PC and the power supply to be used for deployment. • Start ViewArgonaut/Deployment and select SDI-12 Deployment. • Verify hardware configuration parameters using System Configuration Parameters. • Specify all setup parameters for your application. Note that the data format parameter is automatically set to SHORT. • Click Deploy to start data collection. • Disconnect the communication cable from the PC before turning the computer off. • Connect the SDI-12 cable to the data logger. • Install dummy plugs and other cables as needed. Deploy the system. Argonaut Software Manual (March 1, 2001) 15
Page 1 and 2:
Argonaut SL / SW / XR Firmware Vers
Page 3 and 4:
2. Installing the Firmware Update A
Page 5 and 6:
SonTek/YSI 1.3. Assorted Changes Th
Page 7:
A YSI Environmental Company SonTek/
Page 10 and 11:
SonTek 2 • Click Realtime to star
Page 13 and 14:
WARRANTY, TERMS AND CONDITIONS Argo
Page 15 and 16:
TABLE OF CONTENTS Argonaut Operatio
Page 17 and 18:
Argonaut Operation Manual Firmware
Page 19 and 20:
Section 1. Argonaut Components, Ter
Page 21 and 22:
Page 23 and 24:
Section 2. Getting Started Argonaut
Page 25 and 26:
Section 3. Direct Command Interface
Page 27 and 28:
3.2.4. Sleep Mode Argonaut Operatio
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
3.7. System Commands System command
Page 35 and 36:
OutFormat or OF [BINARY|ASCII|SEABI
Page 37 and 38:
Page 39 and 40:
• Parameter range: 0.4 to 10 mete
Page 41 and 42:
AvgInterval or AI [d] • See descr
Page 43 and 44:
3.11. Recorder Commands Recorder co
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
3.15. Run-Time Commands This sectio
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Section 4. Compass/Tilt Sensor Oper
Page 59 and 60:
system will change depending on whe
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Section 5. Argonaut Hardware 5.1. A
Page 67 and 68:
Page 69 and 70:
5.3. Argonaut Processor Argonaut Op
Page 71 and 72:
5.4. Communication Baud Rate Settin
Page 73 and 74:
8-pin UWM Male IL-8-MP to Argonaut
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Section 6. Operational Consideratio
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
XYZ coordinate system Argonaut Oper
Page 87 and 88:
Page 89 and 90:
6.8. Troubleshooting Argonaut Opera
Page 91 and 92:
6.9. Protection from Biological Fou
Page 93 and 94:
Section 7. Autonomous Deployment 7.
Page 95 and 96:
7.3. Starting an Autonomous Deploym
Page 97 and 98:
Section 8. Argonaut Optional Featur
Page 99 and 100:
8.2. Pressure Series Data Conversio
Page 101 and 102:
8.3.2. CTD ASCII Data Format Argona
Page 103 and 104:
Section 9. Additional Support Argon
Page 105 and 106:
Appendix 1. Argonaut Binary Data Fi
Page 107 and 108: Argonaut Operation Manual Firmware
Page 109 and 110: A1.4. Checksum Calculation Argonaut
Page 111 and 112: Appendix 2. Internal SDI-12 Support
Page 113 and 114: Argonaut Operation Manual Firmware
Page 115 and 116: Figure A2.4. Argonaut to SDI-12 int
Page 117 and 118: A2.3. Setting Up the Argonaut for D
Page 119 and 120: A2.4. Summary of Argonaut SDI-12 Co
Page 121 and 122: A2.5. SDI-12 Command and Response P
Page 123 and 124: A2.5.2. Concurrent Measurement Comm
Page 125 and 126: Where: Data Format Metric English x
Page 127 and 128: A2.5.7. Send Identification Command
Page 129 and 130: Appendix 3. Vertical Beam Support f
Page 131 and 132: Appendix 4. Analog Output Option fo
Page 133 and 134: A4.3. Configuring the Serial-to-AO
Page 135 and 136: A4.4. Configuring the Argonaut-SL/X
Page 137 and 138: ? ?EXIT! command, 24 + +++ (alterna
Page 139 and 140: measurement volume, 2 METRIC output
Page 141 and 142: SonTek/YSI 6837 Nancy Ridge Drive,
Page 143 and 144: TABLE OF CONTENTS SonTek/YSI Sectio
Page 145 and 146: Section 1. Software Summary SonTek/
Page 147 and 148: Section 2. Software Installation So
Page 149 and 150: Section 3. ViewArgonaut Windows Sof
Page 151 and 152: SonTek/YSI 3.3. SonRec Recorder Dat
Page 153 and 154: 3.4. Deployment Upon execution, the
Page 155 and 156: The basic procedure for an autonomo
Page 157: SonTek/YSI Averaging Interval • T
Page 161 and 162: SonTek/YSI Averaging Interval • T
Page 163 and 164: 3.5.1. Real-time User Setup Window
Page 165 and 166: SonTek/YSI Cell Begin / Cell End
Page 167 and 168: SonTek/YSI Active Menu Buttons The
Page 169 and 170: 3.5.3. Data Recording The real-time
Page 171 and 172: Velocity Plot SonTek/YSI • The ve
Page 173 and 174: Open File Copy Screen Print Screen
Page 175 and 176: SonTek/YSI PostProcessing Functions
Page 177 and 178: Two types of data files can be expo
Page 179 and 180: Section 4. SonUtils Windows Softwar
Page 181 and 182: The SonTermW window is divided into
Page 183 and 184: The CompCalW window is divided into
Page 185 and 186: The SonRecW window is divided into
Page 187 and 188: SonTek/YSI Section 5. Real-Time Dat
Page 189 and 190: SonTek/YSI For example, the followi
Page 191 and 192: SonTek/YSI simplify post-processing
Page 193 and 194: SonTek/YSI Tabular Data The tabular
Page 195 and 196: SonTek/YSI record containing time,
Page 197 and 198: Section 6. GARG*/EARG* Data Extract
Page 199 and 200: SonTek/YSI Signal strength data is
Page 201 and 202: SonTek/YSI The program generates ta
Page 203 and 204: SonTek/YSI Section 7. Deployment Su
Page 205 and 206: Figure 17 - ARGCHECK Output - Near
Page 207 and 208: SonTek/YSI When looking at the ARGC
Page 209 and 210:
Section 9. Terminal Emulation with
Page 211 and 212:
Section 10. Recorder Data Extractio
Page 213 and 214:
Section 11. Additional Support SonT
Page 215 and 216:
Appendix 1. Automatic File Naming C
Page 217 and 218:
Index A ARG.LOG, 51 ArgCheck [ViewA
Page 219 and 220:
Argonaut Principles of Operation 68
Page 221 and 222:
1. Introduction Argonaut Principles
Page 223 and 224:
Argonaut Principles of Operation (M
Page 225 and 226:
Page 227 and 228:
5.4. Percent Good Argonaut Principl
Page 229 and 230:
Page 231 and 232:
Index A accuracy, 8 along-beam velo
Page 233 and 234:
Using Frequency Pressure Sensors wi
Page 235 and 236:
3.2. The Paroscientific Digiquartz
Page 237 and 238:
Show DRUCK or Show PAROSFREQ • Di
Page 239 and 240:
5.2. PC-ADP Header Extraction: GADP
show all

SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

Create successful ePaper yourself

Delete template?

Save as template?