SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

Recommendations

Info

SonTek/YSI 3.4. Command Syntax Throughout this manual, we refer to a BREAK when discussing direct communications with the Argonaut. Definition of BREAK: 10 • The BREAK is a serial communication signal that causes a hardware reset and places the instrument in command mode. A BREAK consists of holding the data input line high for a period of at least 300 milliseconds. Most terminal emulators include the ability to send a BREAK; SonTerm (supplied with the Argonaut) uses Alt+B. These are the basic rules for direct communication with the Argonaut. 1. The Argonaut can be brought into the command mode from any other mode by sending a BREAK. 2. All commands consist of a single keyword that may be followed by one or more ASCII parameters. The commands and parameters are not case sensitive. 3. When the Argonaut has completed a command and is ready to accept another command, it will send the prompt character “>”. 4. Parameters may be numeric (either integer or floating point), alphanumeric, or a combination (e.g., a date or time string). 5. Commands must be terminated by a carriage return – . 6. The Argonaut echoes every character as it is received (except for run-time commands received during data collection – see Section 3.15). 7. After receiving the that signals the end of the command string, the Argonaut echoes with an additional line feed character – . 8. If the Argonaut recognizes a command as valid it will transmit: OK. 9. If a command is not recognized, the parameters are out of range, or the command cannot be executed in the present state, the Argonaut returns an error message followed by . IMPORTANT: • When some computers and data loggers are turned on or off, they send a signal out the serial port that can be interpreted by the Argonaut as a BREAK. • If the Argonaut is connected to the serial port, this can interrupt data collection or bring the Argonaut out of sleep mode and cause the loss of data or the draining of the batteries. • Always disconnect the Argonaut from the computer or data logger before turning the computer on or off. Argonaut Operation Manual Firmware Version 7.9 (May 1, 2001)
Argonaut Operation Manual Firmware Version 7.9 (May 1, 2001) SonTek/YSI 3.5. Direct Command Summary The tables below summarize all direct commands that can be used with the Argonaut, including any abbreviations (shorter versions of the same command). These commands are split into different sections, and different tables, based on their function. Further details on individual commands are provided in the sections that follow. The following abbreviations are used for input parameters to the Argonaut. • d Integer input (e.g., 30) • d.d Decimal real number input (e.g., 0.33, 1.5) • yy/mm/dd Date as year, month, and day (e.g., 1996/05/20 or 96/05/20) • hh:mm:ss 24-hour clock with hour, minute, and second (e.g., 18:15:00) Help Commands (Section 3.6) Command Short Function Help H or ? Available help categories Help System H/? System General system commands Help Setup H/? Setup Real-time data collection commands Help Deploy H/? Deploy Autonomous deployment commands Help Sdi12 H/? Sdi12 SDI-12 interface control commands (if applicable) Help Recorder H/? Recorder Data recorder commands Help Sensor H/? Sensor Peripheral sensor commands Help Compass H/? Compass Compass/tilt sensor commands Help Show H/? Show Commands to display system configuration System Commands (Section 3.7) Command Short Function Parameters Start (none) Starts real-time data collection (enters data acquisition mode) Deploy (none) Starts autonomous deployment (enters deployment mode) SaveSetup (none) Save current parameters to EEPROM Defaults DEF Sets all parameters to factory defaults Ver (none) Shows CPU firmware version DSPVer (none) Shows DSP firmware version BoardRev (none) Shows electronics board revision number SerNum (none) Shows Argonaut serial number Date (none) Shows / sets system clock date yy/mm/dd Time (none) Shows / sets system clock time hh:mm:ss PowerOff (none) Puts Argonaut in sleep mode AutoSleep AS If ON, Argonaut enters reduced power state during gaps in data collection On / Off OutMode OM Selects data output mode Auto / Polled OutFormat OF Specifies output data format Ascii, Binary, or SeaBird Recorder (none) Turns internal recording on or off On / Off RecMode (none) Sets recording mode (Buffer not enabled) Normal/Buffer 11
Page 1 and 2: Argonaut SL / SW / XR Firmware Vers
Page 3 and 4: 2. Installing the Firmware Update A
Page 5 and 6: SonTek/YSI 1.3. Assorted Changes Th
Page 7: A YSI Environmental Company SonTek/
Page 10 and 11: SonTek 2 • Click Realtime to star
Page 13 and 14: WARRANTY, TERMS AND CONDITIONS Argo
Page 15 and 16: TABLE OF CONTENTS Argonaut Operatio
Page 17 and 18: Argonaut Operation Manual Firmware
Page 19 and 20: Section 1. Argonaut Components, Ter
Page 23 and 24: Section 2. Getting Started Argonaut
Page 25 and 26: Section 3. Direct Command Interface
Page 27: 3.2.4. Sleep Mode Argonaut Operatio
Page 33 and 34: 3.7. System Commands System command
Page 35 and 36: OutFormat or OF [BINARY|ASCII|SEABI
Page 39 and 40: • Parameter range: 0.4 to 10 mete
Page 41 and 42: AvgInterval or AI [d] • See descr
Page 43 and 44: 3.11. Recorder Commands Recorder co
Page 49 and 50: 3.15. Run-Time Commands This sectio
Page 57 and 58: Section 4. Compass/Tilt Sensor Oper
Page 59 and 60: system will change depending on whe
Page 65 and 66: Section 5. Argonaut Hardware 5.1. A
Page 69 and 70: 5.3. Argonaut Processor Argonaut Op
Page 71 and 72: 5.4. Communication Baud Rate Settin
Page 73 and 74: 8-pin UWM Male IL-8-MP to Argonaut
Page 79 and 80:
Section 6. Operational Consideratio
Page 81 and 82:
Argonaut Operation Manual Firmware
Page 83 and 84:
Page 85 and 86:
XYZ coordinate system Argonaut Oper
Page 87 and 88:
Page 89 and 90:
6.8. Troubleshooting Argonaut Opera
Page 91 and 92:
6.9. Protection from Biological Fou
Page 93 and 94:
Section 7. Autonomous Deployment 7.
Page 95 and 96:
7.3. Starting an Autonomous Deploym
Page 97 and 98:
Section 8. Argonaut Optional Featur
Page 99 and 100:
8.2. Pressure Series Data Conversio
Page 101 and 102:
8.3.2. CTD ASCII Data Format Argona
Page 103 and 104:
Section 9. Additional Support Argon
Page 105 and 106:
Appendix 1. Argonaut Binary Data Fi
Page 107 and 108:
Page 109 and 110:
A1.4. Checksum Calculation Argonaut
Page 111 and 112:
Appendix 2. Internal SDI-12 Support
Page 113 and 114:
Page 115 and 116:
Figure A2.4. Argonaut to SDI-12 int
Page 117 and 118:
A2.3. Setting Up the Argonaut for D
Page 119 and 120:
A2.4. Summary of Argonaut SDI-12 Co
Page 121 and 122:
A2.5. SDI-12 Command and Response P
Page 123 and 124:
A2.5.2. Concurrent Measurement Comm
Page 125 and 126:
Where: Data Format Metric English x
Page 127 and 128:
A2.5.7. Send Identification Command
Page 129 and 130:
Appendix 3. Vertical Beam Support f
Page 131 and 132:
Appendix 4. Analog Output Option fo
Page 133 and 134:
A4.3. Configuring the Serial-to-AO
Page 135 and 136:
A4.4. Configuring the Argonaut-SL/X
Page 137 and 138:
? ?EXIT! command, 24 + +++ (alterna
Page 139 and 140:
measurement volume, 2 METRIC output
Page 141 and 142:
SonTek/YSI 6837 Nancy Ridge Drive,
Page 143 and 144:
TABLE OF CONTENTS SonTek/YSI Sectio
Page 145 and 146:
Section 1. Software Summary SonTek/
Page 147 and 148:
Section 2. Software Installation So
Page 149 and 150:
Section 3. ViewArgonaut Windows Sof
Page 151 and 152:
SonTek/YSI 3.3. SonRec Recorder Dat
Page 153 and 154:
3.4. Deployment Upon execution, the
Page 155 and 156:
The basic procedure for an autonomo
Page 157 and 158:
SonTek/YSI Averaging Interval • T
Page 159 and 160:
3.4.2. SDI-12 Deployment Setup Para
Page 161 and 162:
SonTek/YSI Averaging Interval • T
Page 163 and 164:
3.5.1. Real-time User Setup Window
Page 165 and 166:
SonTek/YSI Cell Begin / Cell End
Page 167 and 168:
SonTek/YSI Active Menu Buttons The
Page 169 and 170:
3.5.3. Data Recording The real-time
Page 171 and 172:
Velocity Plot SonTek/YSI • The ve
Page 173 and 174:
Open File Copy Screen Print Screen
Page 175 and 176:
SonTek/YSI PostProcessing Functions
Page 177 and 178:
Two types of data files can be expo
Page 179 and 180:
Section 4. SonUtils Windows Softwar
Page 181 and 182:
The SonTermW window is divided into
Page 183 and 184:
The CompCalW window is divided into
Page 185 and 186:
The SonRecW window is divided into
Page 187 and 188:
SonTek/YSI Section 5. Real-Time Dat
Page 189 and 190:
SonTek/YSI For example, the followi
Page 191 and 192:
SonTek/YSI simplify post-processing
Page 193 and 194:
SonTek/YSI Tabular Data The tabular
Page 195 and 196:
SonTek/YSI record containing time,
Page 197 and 198:
Section 6. GARG*/EARG* Data Extract
Page 199 and 200:
SonTek/YSI Signal strength data is
Page 201 and 202:
SonTek/YSI The program generates ta
Page 203 and 204:
SonTek/YSI Section 7. Deployment Su
Page 205 and 206:
Figure 17 - ARGCHECK Output - Near
Page 207 and 208:
SonTek/YSI When looking at the ARGC
Page 209 and 210:
Section 9. Terminal Emulation with
Page 211 and 212:
Section 10. Recorder Data Extractio
Page 213 and 214:
Section 11. Additional Support SonT
Page 215 and 216:
Appendix 1. Automatic File Naming C
Page 217 and 218:
Index A ARG.LOG, 51 ArgCheck [ViewA
Page 219 and 220:
Argonaut Principles of Operation 68
Page 221 and 222:
1. Introduction Argonaut Principles
Page 223 and 224:
Argonaut Principles of Operation (M
Page 225 and 226:
Page 227 and 228:
5.4. Percent Good Argonaut Principl
Page 229 and 230:
Page 231 and 232:
Index A accuracy, 8 along-beam velo
Page 233 and 234:
Using Frequency Pressure Sensors wi
Page 235 and 236:
3.2. The Paroscientific Digiquartz
Page 237 and 238:
Show DRUCK or Show PAROSFREQ • Di
Page 239 and 240:
5.2. PC-ADP Header Extraction: GADP
show all

SonTek/YSI Argonaut-XR Technical Manual - HydroScientific West

Create successful ePaper yourself

Delete template?

Save as template?