Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>Audio</strong><br />
<strong>Audio</strong> Delay<br />
Default settings are underlined.<br />
Audyssey<br />
Default settings are underlined.<br />
While viewing video, manually adjust the time to delay audio output.<br />
0ms – 200ms<br />
Setting details<br />
• This item can be set within the range of 0 to 100 ms when “Auto Lip Sync” (vpage 120) is set to<br />
“On” and when a TV compatible with Auto Lip Sync is connected.<br />
• Store “<strong>Audio</strong> Delay” for each input source.<br />
• <strong>Audio</strong> Delay for game mode can be set when “Video Mode” (vpage 121) is set to “Auto” or<br />
“Game”.<br />
Volume<br />
Set the MAIN ZONE (room where the unit is located) volume setting.<br />
Setting items<br />
Scale<br />
Set how volume is<br />
displayed.<br />
Limit<br />
Make a setting for<br />
maximum volume.<br />
Power On Level<br />
Define the volume setting<br />
that is active when the<br />
power is turned on.<br />
Mute Level<br />
Set the amount of<br />
attenuation when muting<br />
is on.<br />
Default settings are underlined.<br />
Setting details<br />
0 – 98 : Display in the range 0 (Min) to 98.<br />
–79.5dB – 18.0dB : Display ---dB (Min), in the range –79.5 dB to 18.0 dB.<br />
• The “Scale” setting is applied also to the “Limit” and “Power On Level”<br />
display method.<br />
• The “Scale” setting applies to all zones.<br />
Off : Do not set a maximum volume.<br />
60 (–20dB) / 70 (–10dB) / 80 (0dB)<br />
Last : Use the memorized setting from the last session.<br />
Mute : Always use the muting on condition when power is turned on.<br />
1 – 98 (–79dB – 18dB) : The volume is adjusted to the set level.<br />
Full : The sound is muted entirely.<br />
–40dB : The sound is attenuated by 40 dB down.<br />
–20dB : The sound is attenuated by 20 dB down.<br />
Set Audyssey MultEQ ® XT, Audyssey Dynamic EQ ® and Audyssey Dynamic Volume ® . These can be<br />
selected after Audyssey ® Setup has been performed. For additional information on Audyssey technology,<br />
please see page 168.<br />
NOTE<br />
• If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup,<br />
you may not be able to select Dynamic EQ/Dynamic Volume.<br />
In this case, either perform Audyssey ® Setup over again or perform “Restore...” (vpage 35) to<br />
return to the settings after Audyssey ® Setup was run.<br />
• When HD <strong>Audio</strong> for which the sampling frequency exceeds 96 kHz is played back, the “Audyssey”<br />
cannot be set.<br />
Setting items<br />
MultEQ ® XT<br />
MultEQ ® XT compensates<br />
for both time and<br />
frequency characteristics<br />
of the listening area based<br />
on Audyssey ® Setup<br />
measurement results.<br />
Selection is done from three<br />
types of compensation<br />
curves. We recommend the<br />
“Audyssey” setting.<br />
MultEQ ® XT is the<br />
prerequisite function for<br />
Dynamic EQ and Dynamic<br />
Volume.<br />
Setting details<br />
Audyssey : Optimize the frequency response of all speakers.<br />
Audyssey Byp. L/R : Optimize frequency response of speakers except<br />
front L and R speakers.<br />
Audyssey Flat : Optimize frequency response of all speakers to flat<br />
response.<br />
Graphic EQ : Apply frequency response set with “Graphic EQ”<br />
(vpage 118).<br />
Off : Turn “MultEQ ® XT” equalizer off.<br />
• “Audyssey”, “Audyssey Byp. L/R” and “Audyssey Flat” can be<br />
selected after Audyssey ® Setup has been performed. “Audyssey”<br />
is automatically selected after performing Audyssey ® Setup. When<br />
“Audyssey”, “Audyssey Byp. L/R” or “Audyssey Flat” is selected,<br />
illuminates.<br />
• After running Audyssey ® Setup, if the Speaker Configuration, Distance,<br />
Channel Level, and Crossover Frequency have changed without<br />
increasing the number of speakers measured, only illuminates.<br />
NOTE<br />
When using headphones, “MultEQ ® XT” is automatically set to “Off”.<br />
“MultEQ ® XT”, “Dynamic EQ” and “Dynamic Volume” settings are stored for each input source.<br />
116