Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Symptom Cause/Solution Page<br />
• Check the subwoofer connections.<br />
No sound is<br />
produced from<br />
subwoofer.<br />
DTS sound is not<br />
output.<br />
Dolby TrueHD, DTS-<br />
HD, Dolby Digital<br />
Plus audio is not<br />
output.<br />
Dolby PLg mode or<br />
DTS NEO:6 mode<br />
cannot be selected.<br />
Audyssey MultEQ ®<br />
XT, Audyssey<br />
Dynamic EQ ® and<br />
Audyssey Dynamic<br />
Volume ® cannot be<br />
selected.<br />
Audyssey DSX ®<br />
cannot be selected.<br />
Audyssey Dynamic<br />
EQ ® and Audyssey<br />
Dynamic Volume ®<br />
cannot be selected.<br />
• Turn on the subwoofer’s power.<br />
• Set “Speaker Config.” – “Subwoofer” on the menu to “Yes”.<br />
• If “Front” and “Center” for “Speaker Config.” are set to “Large”,<br />
and “Subwoofer Mode” is set to “LFE”, no sound may be output<br />
from the subwoofers, depending on the input signal or selected<br />
sound mode.<br />
85, 86, 87, 88,<br />
89, 90, 91<br />
–<br />
130<br />
130, 131<br />
• Set “Decode Mode” on the menu to “Auto” or “DTS”. 127<br />
• Make HDMI connections. 11<br />
• Check that “Speaker Config.” – “Center” or “Surround” is set to<br />
other than “None”. If the speaker system is 2.0/2.1ch, this sound<br />
mode cannot be selected.<br />
• When headphones are used, Dolby PLg or DTS NEO:6 cannot be<br />
selected.<br />
• Switch the sound mode to other than “DIRECT” or “PURE<br />
DIRECT”.<br />
• When headphones are used, Audyssey MultEQ ® XT, Audyssey<br />
Dynamic EQ ® and Audyssey Dynamic Volume ® cannot be<br />
selected.<br />
• Check that “Speaker Config.” – “Front Height” or “Front Wide” is 131<br />
set to other than “None”.<br />
• Check that “Speaker Config.” – “Center” is set to other than 130<br />
“None”.<br />
• Switch the sound mode to DOLBY listening mode or DTS listening 75<br />
mode.<br />
• When headphones are used, Audyssey DSX ® cannot be selected. –<br />
• Run Audyssey ® Setup. 29, 92<br />
130<br />
–<br />
75<br />
–<br />
Symptom Cause/Solution Page<br />
“Restorer” cannot<br />
be selected.<br />
• Check that an analog signal or PCM signal (Sample Rate=44.1/48<br />
kHz) is input. For playback of multichannel signals such as Dolby<br />
Digital or DTS surround, “Restorer” cannot be used.<br />
• Switch the sound mode to other than “DIRECT” or “PURE<br />
DIRECT”.<br />
115<br />
75<br />
When the HDMI<br />
ZONE2 function is<br />
used, in spite of<br />
“Assign Mode”<br />
being set to<br />
“ZONE2”, no audio<br />
is output from the<br />
speakers connected<br />
with this unit.<br />
GFMH<br />
• The HDMI audio signals selected for ZONE2 are only output to the<br />
HDMI ZONE2 OUT connector. (The HDMI audio signals selected<br />
for ZONE2 are not output from the speaker of the TV in ZONE2<br />
that is connected to this unit.)<br />
Symptom Cause/Solution Page<br />
Reception fails, or<br />
there is a lot of noise<br />
or distortion.<br />
• Change the antenna orientation or position.<br />
• Use an FM outdoor antenna.<br />
• Separate the antenna from other connection cables.<br />
–<br />
24<br />
24<br />
24<br />
173