Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
Denon AVR-3313 Manual - Audio Products Australia
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
HDMI control function<br />
If the HDMI control function does not operate properly, check the<br />
following points.<br />
• Is the TV or player compatible with the HDMI control function?<br />
• Is “HDMI Control” (vpage 121) set to “On”?<br />
• Is “Power Off Control” (vpage 121) set to “All” or “Video”?<br />
• Is “Control Monitor” (vpage 121) set for the monitor output<br />
connected to television?<br />
• Is “Control Monitor” (vpage 121) set to the TV that uses the<br />
HDMI control function when this unit is connected to two TVs that<br />
support HDMI connectors?<br />
• Are the HDMI control function settings of all devices correct?<br />
NOTE<br />
• When “HDMI Control” is set to “On”, it consumes more standby<br />
power.<br />
• The HDMI control function controls operations of a TV that is<br />
compatible with the HDMI control function. Make sure that the TV<br />
and HDMI are connected when you perform HDMI control.<br />
• Some functions may not operate depending on the connected TV<br />
or player. Check the owner’s manual of each device for details<br />
beforehand.<br />
• When “Power Off Control” on the menu is set to “Off”<br />
(vpage 121), this unit is not set to standby even if the connected<br />
device is in the standby mode.<br />
• When connection changes are implemented, such as adding<br />
connections to HDMI devices, linked operations may be initialized.<br />
In this case, you will need to reconfigure the settings.<br />
• When “HDMI Control” is set to “On”, it is not possible to assign an<br />
HDMI connector to “TV AUDIO” at “Input Assign” (vpage 125).<br />
• Should any of the operations below be performed, the interlocking<br />
function may be reset, in which case, repeat steps 2 and 3.<br />
• “Input Assign” – “HDMI” (vpage 125) setting has changed.<br />
• “Video Output” (vpage 120) setting is changed.<br />
• There is a change to the connection between the devices and the<br />
HDMI, or an increase in devices.<br />
• The HDMI ZONE2 function is not compatible with the HDMI control<br />
function.<br />
• When the HDMI ZONE2 function is used with “HDMI Control” in the<br />
menu set to “On”, the HDMI ZONE2 function may not fully work.<br />
• If “HDMI Control” in the menu is set to “On” and the power of<br />
ZONE2 is on, this units may behave as follows. It is recommended<br />
to disable the HDMI control function on your TV and player when<br />
using the HDMI ZONE2 function. (Some example behaviors are<br />
listed below.)<br />
• When the power of the TV used for MAIN ZONE is off and the<br />
player selected for ZONE2 starts playback, the TV used for MAIN<br />
ZONE is turned on. In this case, the input source selected for MAIN<br />
ZONE changes to the input source selected for ZONE2.<br />
• When playing back a TV used for MAIN ZONE and ZONE2 with<br />
an HDMI connection, turning off the TV used for MAIN ZONE also<br />
turns off this unit and the player.<br />
• When a same input source is selected for MAIN ZONE and ZONE2,<br />
stopping playback of the player on the TV stops the playback on the<br />
player and the video being played back in ZONE2 as well.<br />
96