Operator's Manual - Sirona - Technical Documentation

More documents

Recommendations

Info

MillingStarting the milling processSirona Dental Systems GmbHOperator's ManualCEREC tableRestorationtypeInlay/Onlay/PartialCrown"Mill Optimized"If an extension is available, thisapplies for the extension.Otherwise the prioritization is asfollows: Lingual, buccal, distal,mesialOther possibilityMesial, distal, buccal,lingualCrown Lingual Mesial, distal, buccal,lingualVeneerDistal (1st or 3rd quadrant),Mesial (2nd or 4th quadrant)Mesial, distal, cervical,incisal8.1.4 Positioning the restoration in a multicolored blockYou can move the restoration in all spatial directions within the block using the"Position" tool until the restoration reaches one of the block limits. The limitsare signaled by a beep and a red block. If the restoration is milled on an MCXL milling unit, you can rotate the restoration along the block holder axis byusing the red buttons on the "Rotate" tool. Tip: If you wish to rotate a fronttooth along the mesial-distal axis, for example, before doing so select "Mesial"or "Distal" as the sprue location in the "Milling preview" dialog.When you click the "Mill" icon, the restoration will be milled in this positionfrom the block. In the case of restorations milled on an inLab milling unit,contortion is not taken into account. The restoration is milled in its initial alignment.emptyRealLife blocksAnterior teeth are positioned as an initial suggestion so that the curvature ofthe labial surface corresponds as closely as possible to the curvature of thedentine core. The position of the restoration can be further adjusted by movingand rotating.For RealLife blocks, the same positioning options are available as for simplelayered blocks. In addition, the restoration can be rotated around the toothaxis using the blue surfaces of the "Rotate" tool.Use the "Form", "Drop" and "Shape" tools before you determine the positionof the restoration in the block. As soon as you switch off the block display, allsetting for alignment in the block are lost. You should therefore ensure thatthe block display remains activated when you start the milling process usingthe "Mill" icon. The position of the sprue location can no longer be freely chosenand lies proximally/labially, depending on the rotation of the restoration.8.2 Starting the milling processIntroductionOnce you have completed the design and assessed the restoration in the millingpreview, you can mill the restoration.59 56 458 D 3344116 D 3344.208.05.14.02 04.2011
Sirona Dental Systems GmbH MillingOperator's ManualGraphics: Selecting the CEREC milling unitSelecting the milling unitNOTICEDescription 1Selecting the milling unitIf several milling units are connected, a dialog box will appear when the "Mill"icon is clicked, where you must select the desired milling unit and confirmwith "OK" .båÖäáëÜ➢Click the "Mill" icon.Graphics: CERECNOTICESelecting a blockDescription 2When you choose a block which is too small, a warning message is displayed.1. Select a block and confirm with "OK".2. Wait until the spindle/workpiece axis has reached the zero position.59 56 458 D 3344D 3344.208.05.14.02 04.2011 117
Page 1 and 2:
kÉï=~ë=çÑW==MQKOMNN`bob`=Palé
Page 3 and 4:
Sirona Dental Systems GmbHOperator'
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Sirona Dental Systems GmbH Introduc
Page 15 and 16:
Sirona Dental Systems GmbH Introduc
Page 17 and 18:
Sirona Dental Systems GmbH Software
Page 19 and 20:
Sirona Dental Systems GmbH Software
Page 21 and 22:
Sirona Dental Systems GmbH User int
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66: Sirona Dental Systems GmbH User int
Page 79 and 80: Sirona Dental Systems GmbH Optical
Page 105 and 106: Sirona Dental Systems GmbH DesignOp
Page 115: Sirona Dental Systems GmbH MillingO
Page 119 and 120: Sirona Dental Systems GmbH MillingO
Page 121 and 122: Sirona Dental Systems GmbH Managing
Page 123 and 124: Sirona Dental Systems GmbH Restorat
Page 163 and 164: Sirona Dental Systems GmbH Adhesive
Page 165 and 166: Sirona Dental Systems GmbH Messages
Page 167 and 168:
Sirona Dental Systems GmbH Messages
Page 169 and 170:
Sirona Dental Systems GmbH Link to
Page 171 and 172:
Sirona Dental Systems GmbH Tips and
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
IndexSirona Dental Systems GmbHOper
Page 181 and 182:
IndexSirona Dental Systems GmbHOper
show all

Operator's Manual - Sirona - Technical Documentation

Create successful ePaper yourself

Delete template?

Save as template?