Operator's Manual - Sirona - Technical Documentation

More documents

Recommendations

Info

MillingStarting the milling processSirona Dental Systems GmbHOperator's ManualCAUTIONMilling chamber doorThe milling chamber door must be closed.3. Open the milling chamber door.WARNINGRisk of injury on milling instruments!If you put your hand in the milling chamber, you could injure it on the millinginstruments.Be careful not to brush against the milling instruments with your hand.4. Insert a ceramic block of the required size and color in the spindle/workpieceaxis (also see Operating Instructions of the milling unit).CAUTIONError message during touch process!Always insert the ceramic block that you selected in the "Select block" dialogbox. Otherwise an error message will be displayed during the touch process.5. Close the milling chamber door and start the milling process (click"Start").CAUTIONDo not activate the sleep modeThe sleep mode of the PC must not be activated during the milling process.The instruments are measured automatically and milling starts.The remaining processing time is displayed continuously.The number of milled restorations is shown so that the service life of the millinginstruments still available can be estimated.CAUTIONCanceling the milling processYou can cancel the milling process at any time by pressing the "Stop" button.59 56 458 D 3344118 D 3344.208.05.14.02 04.2011
Sirona Dental Systems GmbH MillingOperator's ManualWARNINGRisk of injury on the remainder of the ceramic block!The remaining portion of the ceramic block may have sharp edges (e.g. A)that could injury you if it is not removed carefully.Always grasp the remainder of the ceramic block by its metal holder.8.3 Fast grindingbåÖäáëÜBlock selectionCAUTIONLoss of quality!Fast grinding may have a negative influence on the quality of the restoration!If desired, the grinding process can be accelerated for some materials. To dothis, simply set a check mark in the corresponding checkbox of the blockselection dialog box.This mode is faster, however the surface of the milled restoration is slightlyrougher.59 56 458 D 3344D 3344.208.05.14.02 04.2011 119
Page 1 and 2:
kÉï=~ë=çÑW==MQKOMNN`bob`=Palé
Page 3 and 4:
Sirona Dental Systems GmbHOperator'
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Sirona Dental Systems GmbH Introduc
Page 15 and 16:
Sirona Dental Systems GmbH Introduc
Page 17 and 18:
Sirona Dental Systems GmbH Software
Page 19 and 20:
Sirona Dental Systems GmbH Software
Page 21 and 22:
Sirona Dental Systems GmbH User int
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68: Sirona Dental Systems GmbH User int
Page 79 and 80: Sirona Dental Systems GmbH Optical
Page 105 and 106: Sirona Dental Systems GmbH DesignOp
Page 115 and 116: Sirona Dental Systems GmbH MillingO
Page 117: Sirona Dental Systems GmbH MillingO
Page 121 and 122: Sirona Dental Systems GmbH Managing
Page 123 and 124: Sirona Dental Systems GmbH Restorat
Page 163 and 164: Sirona Dental Systems GmbH Adhesive
Page 165 and 166: Sirona Dental Systems GmbH Messages
Page 167 and 168: Sirona Dental Systems GmbH Messages
Page 169 and 170:
Sirona Dental Systems GmbH Link to
Page 171 and 172:
Sirona Dental Systems GmbH Tips and
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
IndexSirona Dental Systems GmbHOper
Page 181 and 182:
IndexSirona Dental Systems GmbHOper
show all

Operator's Manual - Sirona - Technical Documentation

Create successful ePaper yourself

Delete template?

Save as template?