Operator's Manual - Sirona - Technical Documentation

More documents

Recommendations

Info

Restoration types and design techniquesCorrelation (in Master Mode only)Sirona Dental Systems GmbHOperator's Manual10.4.3.8 Examining the milling previewTooth 16 with fissures - Correlation - inLab10.4.3.9 MillingMilling simulationInstructionsThe finished restoration is displayed in the milling preview (see ".Milling preview[ ➙ 114]“).1. Inspect the restoration.2. Select the desired milling mode.3. Set the sprue location on a flat, convexly curved side.Instructions1. If you are satisfied with the restoration, click the "Mill" icon (see "Mill" [ ➙114]).2. Start the milling process (see also Operating Instructions of the millingunit).10.4.4 Design example of crown for tooth 2610.4.4.1 Creating a new restorationInstructions✔ You have selected a patient from the database or created a new patient.1. In the "New" dialog, select the information stated below.2. Click "OK".RangeValue"Restoration""Crown""Design technique" "Correlation"Tooth 26Crown for tooth 26 (Master/inLab)10.4.4.2 Acquiring the occlusionNOTICEObserve instructionsObserve central instruction / instructions inLabThe occlusion of the tooth to be restored must be located in the center of theimage during the acquisition. Observe the instructions under "General informationon the optical impression".Prerequisite for reconstructing occlusal surface with powdered working field1. Reconstruct the occlusal surface provisionally and check the contact situation.2. Move the arrow cursor to the icon marked "Acquire occlusion".59 56 458 D 3344154 D 3344.208.05.14.02 04.2011
Sirona Dental Systems GmbH Restoration types and design techniquesOperator's Manual3. Remove the 3D camera from its holder and position it above the powderedworking field.4. Acquire the occlusion.10.4.4.3 Acquiring the preparation3D cameraCEREC instructions1. Acquire the preparation (see "Optical impression").NOTICEObserve instructionsThe prepared tooth must be located in the center of the image during the acquisition.Observe the instructions under "General information on the opticalimpression" [ ➙ 147].2. If all of the required optical impressions are available, click the icon marked"Next".Graphics: Crown for tooth 26, inLab/CERECbåÖäáëÜ3D display10.4.4.4 Hiding image regionsCrown for tooth 26, inLab/CERECDrawing the trimming line59 56 458 D 3344D 3344.208.05.14.02 04.2011 155
Page 1 and 2:
kÉï=~ë=çÑW==MQKOMNN`bob`=Palé
Page 3 and 4:
Sirona Dental Systems GmbHOperator'
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Sirona Dental Systems GmbH Introduc
Page 15 and 16:
Sirona Dental Systems GmbH Introduc
Page 17 and 18:
Sirona Dental Systems GmbH Software
Page 19 and 20:
Sirona Dental Systems GmbH Software
Page 21 and 22:
Sirona Dental Systems GmbH User int
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Sirona Dental Systems GmbH Optical
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104: Sirona Dental Systems GmbH Optical
Page 105 and 106: Sirona Dental Systems GmbH DesignOp
Page 115 and 116: Sirona Dental Systems GmbH MillingO
Page 121 and 122: Sirona Dental Systems GmbH Managing
Page 123 and 124: Sirona Dental Systems GmbH Restorat
Page 153: Sirona Dental Systems GmbH Restorat
Page 163 and 164: Sirona Dental Systems GmbH Adhesive
Page 165 and 166: Sirona Dental Systems GmbH Messages
Page 167 and 168: Sirona Dental Systems GmbH Messages
Page 169 and 170: Sirona Dental Systems GmbH Link to
Page 171 and 172: Sirona Dental Systems GmbH Tips and
Page 177 and 178: Sirona Dental Systems GmbHOperator'
Page 179 and 180: IndexSirona Dental Systems GmbHOper
Page 181 and 182: IndexSirona Dental Systems GmbHOper
show all

Operator's Manual - Sirona - Technical Documentation

Create successful ePaper yourself

Delete template?

Save as template?