Manual - Famco

More documents

Recommendations

Info

Chapter 6 - Parameter Description [I/O]I/O-50: Auto (Sequence) OperationI/O-51: Sequence Number Selection (Seq #)I/O-52: The Number of Steps of Sequence #I/O► Auto mode50 None50Factory Default: None 0There are two modes of ‘Auto-A’ and ‘Auto-B’ in Automode. Auto operation is activated by the multi-functioninput terminals set to [SEQ-L], [SEQ-M], [SEQ-H] and[Go step] in I/O-12 ~ I/O-14.I/O► Seq select51 351Factory Default: 1 101StepFrequencyParameterCodeSpeed-H(P3)Speed-M(P2)Speed-L(P1)Sequence 1 0 0 1Sequence 2 0 1 0I/O-50 ~Sequence 3 1 0 0I/O-84Sequence 4 0 1 1Sequence 50: OFF, 1: ONOutput FrequencySeq1 / 2FSeq1 / 1F1D(Forward)2D(Forward)1 0 1This code selects the sequence to set frequency,transient time, steady speed time and motor direction thesteps.I/O► Step number52 2 522Seq1 / 3F3D(Reverse)1T 1S 2T 2S 3T 3STimeFactory Default: 2 2This code sets the number of steps to use for thesequence number selected in I/O-51.P1-CM‘SEQ-L’ON[Example 1 of ‘Auto-A’ operation]Time[Auto-A]This mode will allow the inverter to operate automaticallyfollowed by its pre-programmed sequence. According tothis sequence, eight different steps of Frequency,Transient Time, Steady Speed time and Motor Directioncan be initiated with only a single multi-function inputcontact closure (I/O-12 ~ I/O-14). The sequence andsteps are set in I/O-51 ~ I/O-84.Output FrequencySequence 1 Sequence 3 Sequence 2SEQ1 / 2FSEQ2 / 2FSEQ1 / 1FSEQ3 / 2FTimeSEQ3 / 1FP1-CM‘SEQ-L’ONTimeP2-CM‘SEQ-M’ONTime[Example 2 of ‘Auto-A’ operation]134
Chapter 6 - Parameter Description [I/O][AUTO B]This mode can be also used to program up to 8 differentsteps as Auto A. However, to switch from one step toanother, an external contact closure set to ‘Go step’ isrequired.Output FrequencySEQ1 / 2FSequence 1 Sequence 3 Sequence 2I/O-85~ I/O 97: Step frequecy 8, 9, 10, 11, 12, 13,14, 15, Multi-function input terminal RST, BX,JOG. FX, RX DefineSee the description pages of I/O 21~39 for more details.SEQ2 / 2FSEQ1 / 1FSEQ3 / 2FTimeSEQ3 / 1FP1-CM‘SEQ-L’P2-CM‘SEQ-M’ONONP3-CM‘Go step’ ON ON ON ON ONTimeTimeTimeMinimum 100msec[Example of ‘Auto-B’ operation]☞ Note: When a new sequence is selected during asequence operating, the new sequence starts after thecurrent sequence is finished.I/O-53 ~ I/O-84: Frequency, Transient Time,Steady Speed Time, Motor Direction setting ofeach Step and SequenceThese parameter codes set the frequency, transient time,steady speed time, and motor direction. These codesare displayed according to the sequence number andsteps.135
Page 3:
CAUTION• Install the inverter on
Page 6:
(9) UL Marking1. Short Circuit Rati
Page 9 and 10:
USER SELECTION GUIDE (iS5 SPECIFICA
Page 11 and 12:
CONTROLOPERATIONProtectionDisplayEn
Page 13 and 14:
Chapter 1 - Installation1.4 Other P
Page 15 and 16:
Chapter 1 - Installation• Frame #
Page 17 and 18:
Chapter 1 - Installation• Frame #
Page 19 and 20:
Chapter 1 - Installation1.6 Basic W
Page 21 and 22:
Chapter 1 - Installation1.7.1 Type
Page 23 and 24:
Chapter 1 - InstallationWARNINGNorm
Page 25 and 26:
Chapter 1 - Installation1.8 Control
Page 28 and 29:
Chapter 1 - InstallationNotes:22
Page 31 and 32:
Chapter 2 - Operation2.2.1 LCD Keyp
Page 33 and 34:
Chapter 2 - Operation2.2.3 Paramete
Page 35 and 36:
Chapter 2 - Operation2.3.1 7-Segmen
Page 37 and 38:
Chapter 2 - Operation2.3.3 Paramete
Page 39 and 40:
Chapter 2 - Operation2.5 Operating
Page 41 and 42:
Chapter 2 - Operation2.5.2 Operatio
Page 43 and 44:
Chapter 2 - Operation2.5.3 Operatio
Page 45 and 46:
Chapter 3 - Function Settings3) V/F
Page 47 and 48:
Chapter 3 - Function SettingsParame
Page 49 and 50:
Chapter 3 - Function Settings5) Par
Page 51 and 52:
Chapter 3 - Function Settings3) Aut
Page 53 and 54:
MODE PROG ENTREVSTOPRESETSHIFTESCFW
Page 55 and 56:
Chapter 3 - Function SettingsOperat
Page 57 and 58:
CHAPTER 4 -QUICK-START PROCEDURESTh
Page 59 and 60:
Chapter 4 - Quick start procedures4
Page 61 and 62:
Chapter 4 - Quick start procedures4
Page 63 and 64:
Chapter 5 - Parameter ListCodeDescr
Page 65 and 66:
Chapter 5 - Parameter ListCodeFU1-2
Page 67 and 68:
Page 69 and 70:
Chapter 5 - Parameter ListCodeFU2-7
Page 71 and 72:
Chapter 5 - Parameter ListCodeI/O-1
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Chapter 5 - Parameter ListCodeEXT-0
Page 79 and 80:
Chapter 5 - Parameter ListCodeEXT-3
Page 81 and 82:
Page 83 and 84:
Chapter 5 - Parameter List5.8 Sub-B
Page 85 and 86:
CHAPTER 6 -PARAMETER DESCRIPTION6.1
Page 87 and 88:
Chapter 6 - Parameter Description [
Page 89 and 90: Chapter 6 - Parameter Description [
Page 139: Chapter 6 - Parameter Description [
Page 159 and 160: CHAPTER 7 -OPTIONSThe iS5 series in
Page 161 and 162: Chapter 7 - Options7.1 Sub-A board7
Page 163 and 164: Chapter 7 - Options7.2 Sub-B Board7
Page 165 and 166: Chapter 7 - Options1. Sub-B board w
Page 167 and 168: Chapter 7 - Options7.3 Sub-C Board
Page 169 and 170: Chapter 7 - Options7.4 Communicatio
Page 171 and 172: Chapter 7 - Options7.5 KeypadThe iS
Page 174 and 175: Chapter 7 - Options2) DB Resistor (
Page 176 and 177: Chapter 7 - Options· DB resistor w
Page 178 and 179: Chapter 7 - Options· DB Resistor/U
Page 180 and 181: Chapter 7 - Options* Type 2 (Max. 6
Page 182 and 183: Chapter 7 - Options3) DB Resistor/U
Page 184 and 185: Chapter 7 - Options• Group 2802-
Page 186 and 187: Chapter 7 - Options(5) Monitoring L
Page 188 and 189: Chapter 8 - Troubleshooting & Maint
Page 190 and 191:
Chapter 8 - Troubleshooting & Maint
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
APPENDIX B - PARAMETERS BASED ON AP
Page 198 and 199:
APPENDIX C- PERIPHERAL DEVICESInver
Page 200 and 201:
DECLARATION OF CONFORMITYCouncil Di
Page 202 and 203:
EMI / RFI POWER LINE FILTERSRFI FIL
Page 204 and 205:
EMI / RFI POWER LINE FILTERSRFI Fil
show all

Manual - Famco

Create successful ePaper yourself

Delete template?

Save as template?