Manual - Famco

More documents

Recommendations

Info

Chapter 1 – Installation1.7.3 Type C ConfigurationA Dynamic Braking Unit or a DC Bus Choke or both of them may be added to iS5 series inverters that have a Type AConfiguration power terminal strip.Jumper Between P1 and P2 Must Be Removed in Orderto Install a DC Bus Choke.R S T G P1 P2 N U V W3 PhasePower InputMotorDynamicBrakingUnitDynamic Braking ResistorFigure 4 – Type C Dynamic Braking Unit, DC Bus Choke InstallationR S T G P1 B1 B2 U V WDC Bus Choke (remove towire DC Reactor3 PhasePower InputMotorDynamic Braking ResistorFigure 5 – Type C Dynamic Braking Resistor1.7.4 Type D ConfigurationR S T G U V W P1 P2 N3 PhasePower InputMotorDynamicBrakingUnitFigure 6 – Type D Dynamic Braking Unit, DC Bus Choke InstallationDB ResistorDC Bus Choke(remove to wire DC Reactor)16
Chapter 1 – InstallationWARNINGNormal stray capacitance between the inverter chassis and the power devices inside theinverter and AC line can provide a high impedance shock hazard. Do not apply power to theinverter if the inverter frame (Power terminal G) is not grounded.1.7.5 Wiring Power Terminals• Wiring Precautions• The internal circuits of the inverter will be damaged if the incoming power is connected and applied to outputterminals (U, V, W).• Use ring terminals with insulated caps when wiring the input power and motor wiring.• Do not leave wire fragments inside the inverter. Wire fragments can cause faults, breakdowns, and malfunctions.• For input and output, use wires with sufficient size to ensure voltage drop of less than 2%.• Motor torque may drop of operating at low frequencies and a long wire run between inverter and motor.• When more than one motor is connected to one inverter, total wire length should be less than 200m (656ft). Donot use a 3-wire cable for long distances. Due to increased leakage capacitance between wires, over-currentprotective feature may operate or equipment connected to the output side may malfunction. (But for products ofless than 3.7kW, the wire length should be less than 50m(146ft).) In case of long wire length, it should be requiredto lower carrier frequency or use Micro Surge Filter.Length between Inverter and Motor Up to 50m Up to 100m More than 100mAllowable Carrier Frequency Less than 15kHz Less than 5kHz Less than 2.5kHz• Connect only recommended braking resistor between the B1 and B2 terminals. Never short B1 and B2terminals. Shorting terminals may cause internal damage to inverter.• The main circuit of the inverter contains high frequency noise, and can hinder communication equipment near theinverter. To reduce noise, install line noise filters on the input side of the inverter.• Do not use power factor capacitor, surge killers, or RFI filters on the output side of the inverter. Doing so maydamage these components.• Always check whether the LCD and the charge lamp for the power terminal are OFF before wiring terminals. Thecharge capacitor may hold high-voltage even after the power is disconnected. Use caution to prevent thepossibility of personal injury.• Grounding• The inverter is a high switching device, and leakage current may flow. Ground the inverter to avoid electrical shock.Use caution to prevent the possibility of personal injury.• Connect only to the dedicated ground terminal of the inverter. Do not use the case or the chassis screw forgrounding.• The protective earth conductor must be the first one in being connected and the last one in being disconnected.• As a minimum, grounding wire should meet the specifications listed below. Grounding wire should be as short aspossible and should be connected to the ground point as near as possible to the inverter.Inverter CapacityGrounding wire Sizes, AWG (mm²)200V Class400VClassBelow 3.7kW (5HP) 12 (3.5) 14 (2)5.5~7.5kW (7.5~10HP) 10 (5.5) 12 (3.5)11~15kW (15~20HP) 6 (14) 8 (8)18.5~22kW (25~30HP) 4 (22) 6 (14)30~37kW (40~50HP) 4 (22) 6 (14)45~75kW (60~100HP) 2 (38) 4 (22)17
Page 3: CAUTION• Install the inverter on
Page 6: (9) UL Marking1. Short Circuit Rati
Page 9 and 10: USER SELECTION GUIDE (iS5 SPECIFICA
Page 11 and 12: CONTROLOPERATIONProtectionDisplayEn
Page 13 and 14: Chapter 1 - Installation1.4 Other P
Page 15 and 16: Chapter 1 - Installation• Frame #
Page 17 and 18: Chapter 1 - Installation• Frame #
Page 19 and 20: Chapter 1 - Installation1.6 Basic W
Page 21: Chapter 1 - Installation1.7.1 Type
Page 25 and 26: Chapter 1 - Installation1.8 Control
Page 28 and 29: Chapter 1 - InstallationNotes:22
Page 31 and 32: Chapter 2 - Operation2.2.1 LCD Keyp
Page 33 and 34: Chapter 2 - Operation2.2.3 Paramete
Page 35 and 36: Chapter 2 - Operation2.3.1 7-Segmen
Page 37 and 38: Chapter 2 - Operation2.3.3 Paramete
Page 39 and 40: Chapter 2 - Operation2.5 Operating
Page 41 and 42: Chapter 2 - Operation2.5.2 Operatio
Page 43 and 44: Chapter 2 - Operation2.5.3 Operatio
Page 45 and 46: Chapter 3 - Function Settings3) V/F
Page 47 and 48: Chapter 3 - Function SettingsParame
Page 49 and 50: Chapter 3 - Function Settings5) Par
Page 51 and 52: Chapter 3 - Function Settings3) Aut
Page 53 and 54: MODE PROG ENTREVSTOPRESETSHIFTESCFW
Page 55 and 56: Chapter 3 - Function SettingsOperat
Page 57 and 58: CHAPTER 4 -QUICK-START PROCEDURESTh
Page 59 and 60: Chapter 4 - Quick start procedures4
Page 61 and 62: Chapter 4 - Quick start procedures4
Page 63 and 64: Chapter 5 - Parameter ListCodeDescr
Page 65 and 66: Chapter 5 - Parameter ListCodeFU1-2
Page 67 and 68: Chapter 5 - Parameter ListCodeDescr
Page 69 and 70: Chapter 5 - Parameter ListCodeFU2-7
Page 71 and 72: Chapter 5 - Parameter ListCodeI/O-1
Page 73 and 74:
Chapter 5 - Parameter ListCodeI/O-4
Page 75 and 76:
Chapter 5 - Parameter ListCodeI/O-9
Page 77 and 78:
Chapter 5 - Parameter ListCodeEXT-0
Page 79 and 80:
Chapter 5 - Parameter ListCodeEXT-3
Page 81 and 82:
Chapter 5 - Parameter ListCodeDescr
Page 83 and 84:
Chapter 5 - Parameter List5.8 Sub-B
Page 85 and 86:
CHAPTER 6 -PARAMETER DESCRIPTION6.1
Page 87 and 88:
Chapter 6 - Parameter Description [
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
CHAPTER 7 -OPTIONSThe iS5 series in
Page 161 and 162:
Chapter 7 - Options7.1 Sub-A board7
Page 163 and 164:
Chapter 7 - Options7.2 Sub-B Board7
Page 165 and 166:
Chapter 7 - Options1. Sub-B board w
Page 167 and 168:
Chapter 7 - Options7.3 Sub-C Board
Page 169 and 170:
Chapter 7 - Options7.4 Communicatio
Page 171 and 172:
Chapter 7 - Options7.5 KeypadThe iS
Page 174 and 175:
Chapter 7 - Options2) DB Resistor (
Page 176 and 177:
Chapter 7 - Options· DB resistor w
Page 178 and 179:
Chapter 7 - Options· DB Resistor/U
Page 180 and 181:
Chapter 7 - Options* Type 2 (Max. 6
Page 182 and 183:
Chapter 7 - Options3) DB Resistor/U
Page 184 and 185:
Chapter 7 - Options• Group 2802-
Page 186 and 187:
Chapter 7 - Options(5) Monitoring L
Page 188 and 189:
Chapter 8 - Troubleshooting & Maint
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
APPENDIX B - PARAMETERS BASED ON AP
Page 198 and 199:
APPENDIX C- PERIPHERAL DEVICESInver
Page 200 and 201:
DECLARATION OF CONFORMITYCouncil Di
Page 202 and 203:
EMI / RFI POWER LINE FILTERSRFI FIL
Page 204 and 205:
EMI / RFI POWER LINE FILTERSRFI Fil
show all

Manual - Famco

Create successful ePaper yourself

Delete template?

Save as template?