Manual - Famco

Chapter 5 - Parameter ListCodeAPP-09APP-10APP-11APP-12APP-13APP-14APP-15APP-16APP-17APP-18APP-19APP-20DescriptionStarting Aux. MotorSelectionOperation Time Displayon Auto ChangeStart Frequency of Aux.Motor 1Start Frequency of Aux.Motor 2Start Frequency of Aux.Motor 3Start Frequency of Aux.Motor 4Stop Frequency of Aux.Motor 1Stop Frequency of Aux.Motor 2Stop Frequency of Aux.Motor 3Stop Frequency of Aux.Motor 4Delay Time beforeOperating Aux MotorDelay Time beforeStopping Aux MotorKeypad DisplaySetting RangeLCD 7-Segment LCD 7-SegmentUnitsFactoryDefaultAdj.DuringRunStarting Aux 09 1 to 4 1 1 Yes 147Auto Op Time 10 - - - - 147Start freq 1 11 0 to FU1-20 0.01 49.99 [Hz] YesStart freq 2 12 0 to FU1-20 0.01 49.99 [Hz] YesStart freq 3 13 0 to FU1-20 0.01 49.99 [Hz] YesStart freq 4 14 0 to FU1-20 0.01 49.99 [Hz] YesStop freq 1 15 0 to FU1-20 0.01 15.00 [Hz] YesStop freq 2 16 0 to FU1-20 0.01 15.00 [Hz] YesStop freq 3 17 0 to FU1-20 0.01 15.00 [Hz]] YesStop freq 4 18 0 to FU1-20 0.01 15.00 [Hz] YesAux start DT 19 0 to 9999 [sec] 0.1 60.0 [sec] YesAux stop DT 20 0 to 9999 [sec] 0.1 60.0 [sec] YesAPP-21 The Number of Aux Motor Nbr Aux’s 21 0 to 4 1 4 Yes 148APP-22 PID Bypass Selection Regul Bypass 22No 0Yes 1Page147148148- No Yes 148APP-23 Sleep Delay Time Sleep Delay 23 0 to 9999 [sec] 0.1 60.0 [sec] Yes 149APP-24 Sleep Frequency Sleep Freq 24 0 to FU1-20 0.01 0.19 [Hz] Yes 149APP-25 Wake-Up Level WakeUp Level 25 0 to 100 [%] 1 35.0 [%] Yes 149APP-26Auto Change ModeSelectionAutoCh-Mode 26 0 to 2 1 1 Yes 149APP-27 Auto Change Time AutoEx-intv 27 00:00 to 99:00 00:01 72:00 YesAPP-28 Auto Change Level AutoEx-level 28 0 to 100 [%] 0.1 20 [%] YesAPP-29 Inter-Lock Selection Inter-lock 29APP-30Feedback Freq/Percentage DisplayNo 0Yes 1150- No Yes 150Fbk/PER 30 [Hz] / [%] - 150APP-31 Actual Value Display Prs 31 [Bar]/[Pa] - - - - 151APP-32 Pressure Display Scale Scale Disp 32 0 to 50000 - 1000 Yes 151APP-33 30 Draw Mode Selection Draw Mode 33None 0V1_Draw 1I_Draw 2V2_Draw 3- None Yes 151APP-34 Draw Size Setting DrawPerc 34 0 to 150 [%] 0.1 100 [%] Yes 15130Code APP-32 through APP-33 appears only when APP-01 is set to ‘Draw’.76