Networking

Networking
Networking
Network enclosures, based on Rittal TS 8, pre-configured
Material:
Sheet steel
Surface finish:
Enclosure frame:
Dipcoat-primed
Doors, roof and base/plinth:
Dipcoat-primed,
powder-coated in RAL 7035
Gland plates, punched sections
with mounting flanges and
mounting angles:
Zinc-plated, passivated
Supply includes:
System frame with doors or rear
panel, roof plate,
vented base/plinth 100 mm,
earthing of all enclosure panels;
Supplied loose:
Levelling feet incl. base/plinth
adaptor,
4 spacers for raising the roof or
vent panel,
4 cable clamp rails for the inner
frame level,
10 cable shunting rings
(105 x 70 mm, plastic),
50 captive nuts, M6, conductive,
50 multi-tooth screws M6.
Version 4
Designer glazed door at the
front, 180°, with comfort handle
for semi-cylinder and security
lock 3524 E;
Sheet steel door at the rear,
130°, with swivel handle and
security lock 3524 E.
Empty enclosure for individual
configuration, 482.6 mm (19″)/
metric partial installation or a
combination of mounting angles/
482.6 mm (19″) mounting
frames supported. Gland plate
at the front, fitted as an infill
panel.
Accessories Page 252 Monitoring Page 187 Climate control Page 113
Version 4 Version 5 Version 6
U 42 42 40
Width (B1) mm 1) 800 800 800
Height (H1 + H2) mm, (H1 + H2 + H4) mm 1) 2000 + 100 2000 + 100 + 25 2000 + 100 + 25
Depth (T1) mm 1) 800 800 800
Clearance width (B2) mm 712 712 712
Clearance height (H3) mm 1912 1912 1912
Clearance depth (T2) in mm 712 712 712
Model No. DK including 2 plug-in side panels,
with security lock 3524 E
Model No. DK as a bayed enclosure without side panels,
incl. baying kit TS 8800.500
1) All sizes are nominal dimensions. For absolute dimensions, please refer to the detailed drawing on the Internet.
2) Delivery times available on request.
3) Aluminium glazed door, delivery times available on request.
7930.400 3) 7930.500 3) 7930.660 3)
– 7930.550 2)3) 7930.670 2)3)
36 Rittal IT catalogue/Networking
T1
T2
H3
B2
B1
H1
H2
Version 5
Designer glazed door at the
front, 180°, with comfort handle
for semi-cylinder and security
lock 3524 E;
Sheet steel door at the rear,
130°, with swivel handle and
security lock 3524 E.
482.6 mm (19″) mounting
angles at the front and rear, distance
between levels 598 mm.
L-shaped mounting angles
screw-fastened to depth stays in
the centre. Roof plate with cutout
for fan insert and vent panel
on spacers. Gland plate at the
front, fitted as an infill panel.
T1
H3
H4
B1
H1
H2
Version 6
Designer glazed door at the
front, 180°, with comfort handle
for semi-cylinder and security
lock 3524 E.
Sheet steel rear panel.
Swing frame, large, with side
trim panel for the installation of
482.6 mm (19″) mounting components
whilst utilising the full
enclosure height (130°, 150 kg).
Full installation at the front, rear
panel, including swing frame
installation kit SR 1995.825 up to
150 kg total load capacity,
static. Roof plate with cut-out for
fan insert and vent panel on
spacers. Gland plate, onepiece,
vented, with cable entry.
Detailed drawing,
available on the Internet.