Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

More documents

Recommendations

Info

GE Oil and Gas SVI II AP Instruction Manual Increasing Signal = CCW Rotation 45° Magnet Axis with Valve Closed Figure 47 Magnet Orientation for 90° Valve Rotation with De-energized Actuator Disk Washer Figure 48 Magnet Holder for Reciprocating Valves Figure 49 Reciprocating Valve Mounting Bracket 64
Checking the Air Supply Check Out and Power Up Using ValVue to Check Magnet Position Use this procedure to check the magnet using ValVue: 1. Connect to the positioner in accordance with the ValVue instructions. For further information refer to the ValVue Instruction Manual. a. Run ValVue. b. Select the installed positioner from the list of Connected Devices. c. Select the: Check tab to view the current operating conditions of the selected positioner. 2. The Raw Position Value should be between – 1000 and +1000 when: Checking the Air Supply A reciprocating or less than 60° rotation rotary valve is closed. A greater than 60° rotation rotary valve is at 45° of rotation (mid stroke for a 90° rotation rotary valve). Use this procedure to check the air supply. 1. Turn on the air supply. 2. Adjust the filter regulator. 3. Supply pressure must be a minimum of 10 psi (.69 bar, 68.97 kPa) greater than the spring range of the actuator but may not exceed the rated actuator pressure. Refer to the valve or actuator instruction manual. 4. Inspect the tubing connections between the filter-regulator and the positioner for leaks. 5. Verify that the tubing is not bent or crushed. 6. Verify that all fittings are leak tight. CAUTION Do not use Teflon pipe seal tape as it can shred into particles harmful to the pneumatic components. 65
Page 1 and 2:
GE Masoneilan * Products SVI * II
Page 3 and 4:
SVI II AP Instruction Manual Docume
Page 5 and 6:
Connecting the Tubing and Air Suppl
Page 7 and 8:
9: Operation and Maintenance ......
Page 9 and 10:
SVI II AP Instruction Manual Figure
Page 11 and 12:
Tables 1 SVI II AP Installation Ste
Page 13 and 14: Safety Information 1 This section p
Page 15 and 16: SVI II AP Product Safety WARNING Be
Page 17 and 18: Introduction 2 The SVI II AP (Smart
Page 19 and 20: Operational Overview Introduction A
Page 21 and 22: Available Options Introduction Avai
Page 23 and 24: Installation and Set Up 3 Overview
Page 25 and 26: SVI II AP Dimensions and Weights In
Page 27 and 28: SVI II AP Dimensions and Weights In
Page 29 and 30: Installation Notes Installation and
Page 31 and 32: Filter Regulator and Tubing Install
Page 33 and 34: Required Tools Installation and Set
Page 35 and 36: Rotary - 90° Installation and Set
Page 37 and 38: Mounting the SVI II AP on a Install
Page 39 and 40: Dismantling the SVI II AP from Inst
Page 41 and 42: Installing the SVI II AP for Double
Page 43 and 44: Installing the SVI II AP Remote Ins
Page 45 and 46: Remote Position Sensor Mounting Ins
Page 47 and 48: Reciprocating Valves: Remote Instal
Page 53 and 54: Configuring the SVI II AP for Insta
Page 55 and 56: Single Acting Positioner Installati
Page 57 and 58: Double Acting Positioner Installati
Page 59 and 60: Connecting the Air Supply Installat
Page 61 and 62: Check Out and Power Up 4 Overview T
Page 63: Verify Mounting and Linkage Check O
Page 67 and 68: Operational Checkout Check Out and
Page 69 and 70: Pushbutton Locks and Check Out and
Page 71 and 72: Using the Digital Interfaces 5 Over
Page 73 and 74: Pushbuttons Using the Digital Inter
Page 75 and 76: Display Menus Using the Digital Int
Page 77 and 78: Configure Menu Using the Digital In
Page 79 and 80: Configure Menu Using the Digital In
Page 81 and 82: VIEW DATA Menu Using the Digital In
Page 83 and 84: FAILSAFE Mode Using the Digital Int
Page 85 and 86: VIEW ERR Diagnostics Messages Using
Page 87 and 88: Display and Clear Error Messages Us
Page 89 and 90: ValVue Using the Digital Interfaces
Page 91 and 92: HART 6 Squawk Command Using the Dig
Page 93 and 94: Configuration and Calibration Using
Page 95 and 96: VIEW DATA Settings Configuration an
Page 97 and 98: Calibration Configuration and Calib
Page 99 and 100: Adjust Input Signal Range Configura
Page 101 and 102: Check-out with a HART Handheld Conf
Page 103 and 104: Configuring and Calibrating with Co
Page 105 and 106: Wiring an SVI II AP 7 Overview The
Page 107 and 108: SVI II AP Setups Wiring an SVI II A
Page 109 and 110: SVI II AP Setups Wiring an SVI II A
Page 111 and 112: Wire Size and Conduit Wiring an SVI
Page 113 and 114: Cabling and Interconnection Wiring
Page 115 and 116:
Setting Loop Addresses for Split Wi
Page 117 and 118:
Multiple Output Circuit Control Wir
Page 119 and 120:
Isolators Wiring an SVI II AP Hazar
Page 121 and 122:
Verify Wiring and Connections Wirin
Page 123 and 124:
HART Communications with Intrinsic
Page 125 and 126:
Output Channel Isolation HART Commu
Page 127 and 128:
Modem and Computer Use in HART Comm
Page 129 and 130:
Operation and Maintenance 9 Princip
Page 131 and 132:
Output Switches Operation and Maint
Page 133 and 134:
Inductive Load Operation and Mainte
Page 135 and 136:
Pneumatic Module Operation and Main
Page 137 and 138:
Pneumatic Module Operation and Main
Page 139 and 140:
Tools Needed Operation and Maintena
Page 141 and 142:
I⁄P Module Removal and Operation
Page 143 and 144:
Relay Removal and Installation Oper
Page 145 and 146:
Upgrading Firmware Operation and Ma
Page 147 and 148:
Specifications and References A Phy
Page 149 and 150:
Physical and Operational Table 20 I
Page 151 and 152:
Physical and Operational Table 24 H
Page 153 and 154:
Physical and Operational Series Ide
Page 155 and 156:
Spare Parts 155
Page 157 and 158:
Spare Parts Relay Spare Part Kit, S
Page 159 and 160:
Air to Open and Air to Close Actuat
Page 161 and 162:
Actuator Action Air to Open and Air
Page 163 and 164:
Air Supply Requirements C Air Suppl
Page 165 and 166:
Adjusting Speed of Response D Adjus
Page 167 and 168:
Advanced Usage E Technology to Maxi
Page 169 and 170:
Diagnostic Valve Tests Diagnostic V
Page 171 and 172:
Glossary F Accuracy Actuator Type A
Page 173 and 174:
DCS Device Description, DD Diagnost
Page 175 and 176:
Hazardous Area High Flow Hot Swappa
Page 177 and 178:
Padj (%) Position Compensation Damp
Page 180:
GE Oil and Gas SVI II ESD SIL 3 Eme
show all

Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

Create successful ePaper yourself

Delete template?

Save as template?