Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

More documents

Recommendations

Info

GE Oil and Gas SVI II AP Instruction Manual VIEW ERR Diagnostics Messages Diagnostic messages are viewed with VIEW ERR from the MANUAL Mode menu or from NORMAL Mode menu. The VIEW ERR menu item allows you to read the current status information. To clear the error messages: 1. Press * at CLR ERR on either the MANUAL or NORMAL mode menus. 2. Exiting from the VIEW ERR menu returns the previous menu. 84
VIEW ERR Diagnostics Messages Using the Digital Interfaces Table 11 Error Messages LCD Description Action Cause RESET Reset occurred due to command or power up. Always present after power up. Warning Normal operation on power up always sets RESET. RESET is sent by HART communications. Use CLEAR ERR to remove warning LOW POWER Input current < 3.6 mA Takes the device to low power ACT ERR Positioner unable to position a valve normally Warning AIR LOW Supply pressure option is configured and supply pressure is < 10 psi (.69 bar, 69 kPa). Otherwise I/P pressure is below 0.8 psi (.05 bar, 5.5 kPa) Warning Mechanical or pneumatic problem POS ERR The position error exceeds configured limit for more than configured time Warning after T1 and Failsafe Pneumatic/ mechanical, configuration, loose magnet KEYBOARD LCD/Button Failure Warning Damaged buttons or LCD electronics MARGN PWR Input signal is insufficient to proceed CALIB ERR Calibrate failed Warning Invalid values for current calibration and input range by HART commands STOP ERR Calibration error. Find STOPS was unsuccessful. Warning Configuration, calibration TUNE ERR Auto tune failed Warning Mechanical or pneumatic problem causes tuning failure STD DIAG A standard diagnostic procedure failed to complete Warning Pneumatic / mechanical, configuration 85
Page 1 and 2:
GE Masoneilan * Products SVI * II
Page 3 and 4:
SVI II AP Instruction Manual Docume
Page 5 and 6:
Connecting the Tubing and Air Suppl
Page 7 and 8:
9: Operation and Maintenance ......
Page 9 and 10:
SVI II AP Instruction Manual Figure
Page 11 and 12:
Tables 1 SVI II AP Installation Ste
Page 13 and 14:
Safety Information 1 This section p
Page 15 and 16:
SVI II AP Product Safety WARNING Be
Page 17 and 18:
Introduction 2 The SVI II AP (Smart
Page 19 and 20:
Operational Overview Introduction A
Page 21 and 22:
Available Options Introduction Avai
Page 23 and 24:
Installation and Set Up 3 Overview
Page 25 and 26:
SVI II AP Dimensions and Weights In
Page 27 and 28:
SVI II AP Dimensions and Weights In
Page 29 and 30:
Installation Notes Installation and
Page 31 and 32:
Filter Regulator and Tubing Install
Page 33 and 34: Required Tools Installation and Set
Page 35 and 36: Rotary - 90° Installation and Set
Page 37 and 38: Mounting the SVI II AP on a Install
Page 39 and 40: Dismantling the SVI II AP from Inst
Page 41 and 42: Installing the SVI II AP for Double
Page 43 and 44: Installing the SVI II AP Remote Ins
Page 45 and 46: Remote Position Sensor Mounting Ins
Page 47 and 48: Reciprocating Valves: Remote Instal
Page 53 and 54: Configuring the SVI II AP for Insta
Page 55 and 56: Single Acting Positioner Installati
Page 57 and 58: Double Acting Positioner Installati
Page 59 and 60: Connecting the Air Supply Installat
Page 61 and 62: Check Out and Power Up 4 Overview T
Page 63 and 64: Verify Mounting and Linkage Check O
Page 65 and 66: Checking the Air Supply Check Out a
Page 67 and 68: Operational Checkout Check Out and
Page 69 and 70: Pushbutton Locks and Check Out and
Page 71 and 72: Using the Digital Interfaces 5 Over
Page 73 and 74: Pushbuttons Using the Digital Inter
Page 75 and 76: Display Menus Using the Digital Int
Page 77 and 78: Configure Menu Using the Digital In
Page 79 and 80: Configure Menu Using the Digital In
Page 81 and 82: VIEW DATA Menu Using the Digital In
Page 83: FAILSAFE Mode Using the Digital Int
Page 87 and 88: Display and Clear Error Messages Us
Page 89 and 90: ValVue Using the Digital Interfaces
Page 91 and 92: HART 6 Squawk Command Using the Dig
Page 93 and 94: Configuration and Calibration Using
Page 95 and 96: VIEW DATA Settings Configuration an
Page 97 and 98: Calibration Configuration and Calib
Page 99 and 100: Adjust Input Signal Range Configura
Page 101 and 102: Check-out with a HART Handheld Conf
Page 103 and 104: Configuring and Calibrating with Co
Page 105 and 106: Wiring an SVI II AP 7 Overview The
Page 107 and 108: SVI II AP Setups Wiring an SVI II A
Page 109 and 110: SVI II AP Setups Wiring an SVI II A
Page 111 and 112: Wire Size and Conduit Wiring an SVI
Page 113 and 114: Cabling and Interconnection Wiring
Page 115 and 116: Setting Loop Addresses for Split Wi
Page 117 and 118: Multiple Output Circuit Control Wir
Page 119 and 120: Isolators Wiring an SVI II AP Hazar
Page 121 and 122: Verify Wiring and Connections Wirin
Page 123 and 124: HART Communications with Intrinsic
Page 125 and 126: Output Channel Isolation HART Commu
Page 127 and 128: Modem and Computer Use in HART Comm
Page 129 and 130: Operation and Maintenance 9 Princip
Page 131 and 132: Output Switches Operation and Maint
Page 133 and 134: Inductive Load Operation and Mainte
Page 135 and 136:
Pneumatic Module Operation and Main
Page 137 and 138:
Pneumatic Module Operation and Main
Page 139 and 140:
Tools Needed Operation and Maintena
Page 141 and 142:
I⁄P Module Removal and Operation
Page 143 and 144:
Relay Removal and Installation Oper
Page 145 and 146:
Upgrading Firmware Operation and Ma
Page 147 and 148:
Specifications and References A Phy
Page 149 and 150:
Physical and Operational Table 20 I
Page 151 and 152:
Physical and Operational Table 24 H
Page 153 and 154:
Physical and Operational Series Ide
Page 155 and 156:
Spare Parts 155
Page 157 and 158:
Spare Parts Relay Spare Part Kit, S
Page 159 and 160:
Air to Open and Air to Close Actuat
Page 161 and 162:
Actuator Action Air to Open and Air
Page 163 and 164:
Air Supply Requirements C Air Suppl
Page 165 and 166:
Adjusting Speed of Response D Adjus
Page 167 and 168:
Advanced Usage E Technology to Maxi
Page 169 and 170:
Diagnostic Valve Tests Diagnostic V
Page 171 and 172:
Glossary F Accuracy Actuator Type A
Page 173 and 174:
DCS Device Description, DD Diagnost
Page 175 and 176:
Hazardous Area High Flow Hot Swappa
Page 177 and 178:
Padj (%) Position Compensation Damp
Page 180:
GE Oil and Gas SVI II ESD SIL 3 Eme
show all

Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?