Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

More documents

Recommendations

Info

GE Oil and Gas SVI II AP Instruction Manual Configure Menu Because calibration depends on certain configuration options you must perform Configuration before you perform Calibration when installing the SVI II AP for the first time. If a change is made in the Air-to-Open / Air-to-Close configuration option or if you move the SVI II AP to a different valve or make any change to the valve position linkage, you must run the find STOPS calibration again. CONFIG CONFIGuration Menu CONFIG * Air to Menu + + + + + Char act Pressure Tight Shut-off Language Menu Units Menu Menu Menu * Setup + Press * to select option. Press + or - to accept and proceed to next menu item. Air to....Menu ATO * ATC Select Air To Open (ATO) or Air To Close (ATC). Must match the actuator exactly. * Char act Menu LINEAR * EQ% 30:1 * EQ% 50:1 * Pressure Units Menu PSI * BAR * KPA Turn tight shutoff on or off to provide maximum actuator force at 0% Tight Shutoff Menu T.S. OFF * - + T.S. ON * * * +/- Language Menu * ENGLISH * FRENCH Select display language EQ% CAMFX * QUICK50 * Select display units for pressure. Displays tight shutoff value if turned on. Press * to change T.S. ON/OFF status. Press + or - to enter new value. Press * to accept new value and proceed to next menu item. CUSTOM Figure 53 CONFIGure Menu 76
Configure Menu Using the Digital Interfaces ATO / ATC WARNING This procedure can cause the valve to move. Before proceeding be sure the valve is isolated from the process. Keep hands clear from moving parts. Valve Characteristics Pressure Units The positioner must be configured as Air-to-Open, ATO, or as Air-to-Close, ATC. This parameter is toggled by the * button. If the positioner has a double acting relay, the action is defined for the output labeled ACT1, or Output 1. To determine if a direct acting positioner is considered ATO or ATC perform the following test: 1. Apply the actuators rated pressure to the positioner supply. Do not exceed actuator pressure rating on the control valve specification sheet. Damage to the valve stem, shaft, or trim can occur. 2. Disconnect the electrical (4 to 20 mA) input signal from the positioner or set it to less than 3.6 mA. 3. Observe the position of the control valve. If it is closed the actuator is ATO. If the valve is open it is ATC. The positioner must be configured to supply the correct relationship between input signal and valve position. This is called the position characteristic. Figure 10 on page 79 lists configuring the positioner characteristics. Use of a linear characteristic is recommended unless the process dynamics or control valve application calls for an alternate characteristic. SVI II AP offers a custom characteristic for specialty applications. Prior to selection of custom, the 10 parameters for the custom characteristic must be entered using ValVue. Select the display units for the optional actuator pressure sensor. The available choices are PSI, BAR or KPA. The choice applies to both the local LCD display and to the displays with ValVue or the HART Handheld communicator. 1. Press * to move from PSI to BAR to KPA. 2. Press + to continue to scroll through the config menu. NOTE The characteristic configured in the positioner is applied in addition to the plug characteristic built into the valve trim. Do not configure a percentage characteristic if the valve has a percentage plug. 77
Page 1 and 2:
GE Masoneilan * Products SVI * II
Page 3 and 4:
SVI II AP Instruction Manual Docume
Page 5 and 6:
Connecting the Tubing and Air Suppl
Page 7 and 8:
9: Operation and Maintenance ......
Page 9 and 10:
SVI II AP Instruction Manual Figure
Page 11 and 12:
Tables 1 SVI II AP Installation Ste
Page 13 and 14:
Safety Information 1 This section p
Page 15 and 16:
SVI II AP Product Safety WARNING Be
Page 17 and 18:
Introduction 2 The SVI II AP (Smart
Page 19 and 20:
Operational Overview Introduction A
Page 21 and 22:
Available Options Introduction Avai
Page 23 and 24:
Installation and Set Up 3 Overview
Page 25 and 26: SVI II AP Dimensions and Weights In
Page 27 and 28: SVI II AP Dimensions and Weights In
Page 29 and 30: Installation Notes Installation and
Page 31 and 32: Filter Regulator and Tubing Install
Page 33 and 34: Required Tools Installation and Set
Page 35 and 36: Rotary - 90° Installation and Set
Page 37 and 38: Mounting the SVI II AP on a Install
Page 39 and 40: Dismantling the SVI II AP from Inst
Page 41 and 42: Installing the SVI II AP for Double
Page 43 and 44: Installing the SVI II AP Remote Ins
Page 45 and 46: Remote Position Sensor Mounting Ins
Page 47 and 48: Reciprocating Valves: Remote Instal
Page 53 and 54: Configuring the SVI II AP for Insta
Page 55 and 56: Single Acting Positioner Installati
Page 57 and 58: Double Acting Positioner Installati
Page 59 and 60: Connecting the Air Supply Installat
Page 61 and 62: Check Out and Power Up 4 Overview T
Page 63 and 64: Verify Mounting and Linkage Check O
Page 65 and 66: Checking the Air Supply Check Out a
Page 67 and 68: Operational Checkout Check Out and
Page 69 and 70: Pushbutton Locks and Check Out and
Page 71 and 72: Using the Digital Interfaces 5 Over
Page 73 and 74: Pushbuttons Using the Digital Inter
Page 75: Display Menus Using the Digital Int
Page 79 and 80: Configure Menu Using the Digital In
Page 81 and 82: VIEW DATA Menu Using the Digital In
Page 83 and 84: FAILSAFE Mode Using the Digital Int
Page 85 and 86: VIEW ERR Diagnostics Messages Using
Page 87 and 88: Display and Clear Error Messages Us
Page 89 and 90: ValVue Using the Digital Interfaces
Page 91 and 92: HART 6 Squawk Command Using the Dig
Page 93 and 94: Configuration and Calibration Using
Page 95 and 96: VIEW DATA Settings Configuration an
Page 97 and 98: Calibration Configuration and Calib
Page 99 and 100: Adjust Input Signal Range Configura
Page 101 and 102: Check-out with a HART Handheld Conf
Page 103 and 104: Configuring and Calibrating with Co
Page 105 and 106: Wiring an SVI II AP 7 Overview The
Page 107 and 108: SVI II AP Setups Wiring an SVI II A
Page 109 and 110: SVI II AP Setups Wiring an SVI II A
Page 111 and 112: Wire Size and Conduit Wiring an SVI
Page 113 and 114: Cabling and Interconnection Wiring
Page 115 and 116: Setting Loop Addresses for Split Wi
Page 117 and 118: Multiple Output Circuit Control Wir
Page 119 and 120: Isolators Wiring an SVI II AP Hazar
Page 121 and 122: Verify Wiring and Connections Wirin
Page 123 and 124: HART Communications with Intrinsic
Page 125 and 126: Output Channel Isolation HART Commu
Page 127 and 128:
Modem and Computer Use in HART Comm
Page 129 and 130:
Operation and Maintenance 9 Princip
Page 131 and 132:
Output Switches Operation and Maint
Page 133 and 134:
Inductive Load Operation and Mainte
Page 135 and 136:
Pneumatic Module Operation and Main
Page 137 and 138:
Pneumatic Module Operation and Main
Page 139 and 140:
Tools Needed Operation and Maintena
Page 141 and 142:
I⁄P Module Removal and Operation
Page 143 and 144:
Relay Removal and Installation Oper
Page 145 and 146:
Upgrading Firmware Operation and Ma
Page 147 and 148:
Specifications and References A Phy
Page 149 and 150:
Physical and Operational Table 20 I
Page 151 and 152:
Physical and Operational Table 24 H
Page 153 and 154:
Physical and Operational Series Ide
Page 155 and 156:
Spare Parts 155
Page 157 and 158:
Spare Parts Relay Spare Part Kit, S
Page 159 and 160:
Air to Open and Air to Close Actuat
Page 161 and 162:
Actuator Action Air to Open and Air
Page 163 and 164:
Air Supply Requirements C Air Suppl
Page 165 and 166:
Adjusting Speed of Response D Adjus
Page 167 and 168:
Advanced Usage E Technology to Maxi
Page 169 and 170:
Diagnostic Valve Tests Diagnostic V
Page 171 and 172:
Glossary F Accuracy Actuator Type A
Page 173 and 174:
DCS Device Description, DD Diagnost
Page 175 and 176:
Hazardous Area High Flow Hot Swappa
Page 177 and 178:
Padj (%) Position Compensation Damp
Page 180:
GE Oil and Gas SVI II ESD SIL 3 Eme
show all

Masoneilan SVI II AP Installation and Maintenance ... - GE Energy

Create successful ePaper yourself

Delete template?

Save as template?