User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDE4.8.3 Programmer Setup menuProgrammer.Set UpChannelsProg Mode AccessProg Edit AccessProg Store AccessRate ResolutionCh1 UnitsCh1 ResolutionCh1 Servo ToCh1 PV InputCh1 SP InputCh2 UnitsCh2 ResolutionCh2 Servo ToCh2 PV InputCh2 SP InputPower Fail ActionMax EventsReset Event 1Reset Event 2Reset Ch1 UVReset Ch2 UVRunHoldResetRun ResetRun HoldWait DigitalWait Analog 1Wait Analog 2AdvanceOperationStatusProgram Num2OperatorSupervisorSupervisor1Deg C0SP23.7 V0 Deg Cl/sec1PV35.9 V431 l/secRamp back20.00.0NoNoYesNoNo1039.7NoSelect...Success1Figure 4.8.3 Programmer Set Up menuChannelsProg Mode AccessThe number of channels to be profiled. 1 = single channel mode, 2 = dual channelsync-all modeSets the minimum access level (Logged off, Operator, Supervisor) for allowing changesto the current program mode (run, hold or reset)Page 128HA030554Issue 7 Nov 12
nanodac RECORDER/CONTROLLER: USER GUIDE4.8.3 Programmer Set Up Menu (Cont.)Prog Edit Access Sets the minimum access level (Logged off, Operator, Supervisor, Engineer) for loadingprograms, and for allowing edits to the current program including permission to advancea segment.Prog Store Access Sets the minimum access level (Logged off, Operator, Supervisor, Engineer) that allowsusers to copy, store and delete programs.Rate Resolution Sets the resolution (0 to 4 decimal places) of ramp rates when read from / written to viascaled integer comms.Ch1 Units Five-character (max.) descriptor for channel 1 units. If wired, the units will be those ofthe wire source.Ch1 Resolution Number of decimal places for channel 1 value. If wired, the value will be that of the wiresource.Ch1 Servo To Determines whether the programmer starts running channel 1 from the control loop'sconfigured set-point (servo to SP), or from the current process value (servo to PV).Ch1 PV Input Various programmer functions (for example Ch1 Servo to PV), require the PV value ofthe loop that the programmer is trying to control. The parameter is normally wired fromthe loop's Track PV parameter.Ch1 SP Input Various programmer functions (for example Ch1 Servo to SP), require the SP value ofthe loop that the programmer is trying to control - it is normally wired from the loop'sTrack SP parameter.Ch2 Units As ‘Ch1 Units’, above but for channel 2. Appears only if ‘Channels’ is set to ‘2’.Ch2 Resolution As ‘Ch1 Resolution’, above, but for channel 2. Appears only if ‘Channels’ is set to ‘2’.Ch2 Servo To As ‘Ch1 Servo To’, above, but for channel 2. Appears only if ‘Channels’ is set to ‘2’.Ch2 PV Input As ‘Ch1 PV Input’, above, but for channel 2. Appears only if ‘Channels’ is set to ‘2’.Ch1 SP Input As ‘Ch1 SP Input’, above, but for channel 2. Appears only if ‘Channels’ is set to ‘2’.Power Fail Action If the power supplied to the instrument is interrupted, the program status is retainedand when power is restored, the instrument performs the selected power fail action.Continue: The programmer set-point returns immediately to its last value prior to thepower down and the program continue to run from that point.Reset: The program resets.Ramp Back: The programmer servos the programmer set-point to the channel PV, andramps to the target set-point at the rate prior to the power-fail. The time remaining forthe segment is recalculated.Notes:1. If the interrupted segment was a 'time to target' ramp, then when power is returned the calculatedramp rate prior to the interruption is used.2. If the interrupted segment was ‘Dwell’, then the ramp rate is determined by the previous rampsegment. On achieving the dwell set-point, the dwell period continues.3. If a previous ramp segment does not exist (i.e. the first segment of a program is a dwell), the dwellcontinues at the 'servo to PV' programmer set-point.Max Events Configures the maximum number of event outputs (0 to 8).Reset Event N Sets the state of event output ‘N’ when the program is in reset. Appears only if ‘MaxEvents’ is > (N-1).Reset Ch1 UV Enter the value to be written to user value 1 when the program is in reset. Appears onlyif ‘<strong>User</strong> Value’ feature is enabled in Programmer.Features configuration (Section 4.8.1).Reset Ch2 UV Enter the value to be written to user value 2 when the program is in reset. Appears onlyif ‘<strong>User</strong> Value’ feature is enabled in Programmer.Features configuration (Section 4.8.1)and ‘Channels’ = ‘2’RunThe input that causes the programmer to place the current program in Run mode.HoldThe input that causes the programmer to place the current program in Hold mode.HA030554Issue 7 Nov 12Page 129
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91: nanodac RECORDER/CONTROLLER: USER G
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

Create successful ePaper yourself

Delete template?

Save as template?