User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionProgrammer.SetUp.Ch2PVInput Channel 2 PV input float32 3a27 14887 Set by Programmer.SetUp.Ch2ResolutionProgrammer.SetUp.Ch2Resolution Channel 2 Resolution uint8 3a47 14919 Not applicableProgrammer.SetUp.Ch2ServoTo Channel 2 servo to (0 = PV; 1 = SP) uint8 3a2b 14891 Not applicableProgrammer.SetUp.Ch2SPInput Channel 2 SP input float32 3a29 14889 0dpProgrammer.SetUp.Ch2Units Channel 2 units string_t 6a8b 27275 Not applicableProgrammer.SetUp.Channels Number of channels uint8 3a20 14880 Not applicableProgrammer.SetUp.FileErrorStatus File error status uint8 3a45 14917 Not applicable0 = Busy 1 = OK 2 = Load open file3 = Store open file 4 =Delete fail 5 = Copy fail6 = Invalid format 7 = Invalid device 8 = Invalid version9 = Invalid number of channels10 = Parameter write failed11 = Store operation failed to complete12 = Load operation failed to complete13 = Delete operation failed to complete14 = Copy operation failed to complete15 = Invalid filename entered or selected16 = General file operation error17 = Would result in more than the ma.x no. of program filesProgrammer.SetUp.Hold Hold (0 = No 1 = Yes) bool 3a39 14905 Not applicableProgrammer.SetUp.MaxEvents Maximum events uint8 3a2d 14893 Not applicableProgrammer.SetUp.Operation Operation uint8 3a40 14912 Not applicable1 = Select 2 =Load 4 = Store8 = Delete 16 = Delete All 32=Copy64 = Copy AllProgrammer.SetUp.PowerFailAction Power fail action (0 = ramp back; 1 = Reset; 2 = Continue) uint8 3a2c 14892 Not applicableProgrammer.SetUp.ProgEditAccess Program edit access level uint8 3a22 14882 Not applicable0 = Logged out 1 = Operator2 = Supervisor 3 = EngineerProgrammer.SetUp.ProgModeAccess Program mode access level (as Program Edit Access, above) uint8 3a21 14881 Not applicableProgrammer.SetUp.ProgNum Program Number uint8 3a48 14920 Not applicableProgrammer.SetUp.ProgStoreAccess Program store access level (as Program Edit Access, above) uint8 3a23 14883 Not applicableProgrammer.SetUp.RateResolution Rate resolution uint8 3a24 14884 Not applicableProgrammer.SetUp.Reset Reset (0 = No 1 = Yes) bool 3a3a 14906 Not applicableProgrammer.SetUp.ResetCh1UserVal Reset channel 1 user value float32 3a36 14902 1dpProgrammer.SetUp.ResetCh2UserVal Reset channel 2 user value float32 3a37 14903 1dpProgrammer.SetUp.ResetEvent1 Reset event 1 (0 = Off, 1 = On) bool 3a2e 14894 Not applicableProgrammer.SetUp.ResetEvent2 Reset event 2 (0 = Off, 1 = On) bool 3a2f 14895 Not applicableProgrammer.SetUp.ResetEvent3 Reset event 3 (0 = Off, 1 = On) bool 3a30 14896 Not applicableProgrammer.SetUp.ResetEvent4 Reset event 4 (0 = Off, 1 = On) bool 3a31 14897 Not applicableProgrammer.SetUp.ResetEvent5 Reset event 5 (0 = Off, 1 = On) bool 3a32 14898 Not applicableProgrammer.SetUp.ResetEvent6 Reset event 6 (0 = Off, 1 = On) bool 3a33 14899 Not applicableProgrammer.SetUp.ResetEvent7 Reset event 7 (0 = Off, 1 = On) bool 3a34 14900 Not applicableProgrammer.SetUp.ResetEvent8 Reset event 8 (0 = Off, 1 = On) bool 3a35 14901 Not applicableProgrammer.SetUp.Run Run (0 = No 1 = Yes) bool 3a38 14904 Not applicableProgrammer.SetUp.RunHold Run Hold (0 = No 1 = Yes) bool 3a3c 14908 Not applicableProgrammer.SetUp.RunReset Run Rese (0 = No 1 = Yes)t bool 3a3b 14907 Not applicableProgrammer.SetUp.Status Status uint8 3a41 14913 Not applicable0 = Inactive 1 = Success 2 = Failed3 = Loading 4 = Storing 5 = Deleting6 = CopyingProgrammer.SetUp.WaitAnalog1 Wait analog input 1 float32 3a3e 14910 0dpProgrammer.SetUp.WaitAnalog2 Wait analog input 2 float32 3a3f 14911 0dpProgrammer.SetUp.WaitDigital Wait Digital (0 = Off 1 = On) bool 3a3d 14909 Not applicableRealTimeEvent.1.Duration Sets the duration for the event to remain On time_t 30e6 12518 Set by Network.Modbus.TimeFormatRealTimeEvent.1.OffDate Sets the date in the month that the event is to switch off uint8 30e8 12520 Not applicableRealTimeEvent.1.OffDay Sets the day the the event is to switch Off uint8 30e9 12521 Not applicable0 = Sunday 1 = Monday 2 = Tuesday3 = Wednesday 4 = Thursday 5 = Friday6 = Saturday 7 = Monday to Friday8 = Saturday to Sunday9 = Every dayRealTimeEvent.1.OffMonth The month number when the event is to switch off uint8 30e7 12519 Not applicableRealTimeEvent.1.OffTime Sets the time that the event is to switch Off time_t 30ea 12522 Set by Network.Modbus.TimeFormatRealTimeEvent.1.OffType 0 = Duration; 1 = Time uint8 30e5 12517 Not applicableRealTimeEvent.1.OnDate Sets the date in the month that the event is to switch on uint8 30e2 12514 Not applicableRealTimeEvent.1.OnDay Sets the day on which event is to switch on (as ‘OffDay’, above) uint8 30e3 12515 Not applicableRealTimeEvent.1.OnMonth The month number when the event is to switch on uint8 30e1 12513 Not applicableRealTimeEvent.1.OnTime Sets the time that the event is to switch On time_t 30e4 12516 Set by Network.Modbus.TimeFormatRealTimeEvent.1.Output The output from the real time event (0 = Off; 1 = On) bool 30eb 12523 Not applicableRealTimeEvent.1.Type Selects the type of Real Time Event uint8 30e0 12512 Not applicable0 = Off 1 = Time and Day 2 = Time and DateRealTimeEvent.2.Duration Sets the duration for the event to remain On time_t 30f6 12534 Set by Network.Modbus.TimeFormatRealTimeEvent.2.OffDate Sets the date in the month that the event is to switch off uint8 30f8 12536 Not applicableRealTimeEvent.2.OffDay Sets the day the the event is to switch Off (as for Event 1) uint8 30f9 12537 Not applicableRealTimeEvent.2.OffMonth Sets the month that the event is to switch off uint8 30f7 12535 Not applicableRealTimeEvent.2.OffTime Sets the time that the event is to switch Off time_t 30fa 12538 Set by Network.Modbus.TimeFormatRealTimeEvent.2.OffType Selects the type that will switch off the event (as for Event 1) uint8 30f5 12533 Not applicableRealTimeEvent.2.OnDate Sets the date in the month that the event is to switch on uint8 30f2 12530 Not applicableHA030554Issue 7 Nov 12Page 220
nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionRealTimeEvent.2.OnDay Sets the day the event is to switch on (as for Event 1) uint8 30f3 12531 Not applicableRealTimeEvent.2.OnMonth Sets the month that the event is to switch on uint8 30f1 12529 Not applicableRealTimeEvent.2.OnTime Sets the time that the event is to switch On time_t 30f4 12532 Set by Network.Modbus.TimeFormatRealTimeEvent.2.Output The output from the real time event (0 = Off; 1 = On) bool 30fb 12539 Not applicableRealTimeEvent.2.Type Selects the type of Real Time Event uint8 30f0 12528 Not applicable0 = Off 1 = Time and Day 2 = Time and DateSegment.1.Ch1Holdback Channel 1 holdback type uint8 3ac9 15049 Not applicable0 = Off 1 = Low 2= High 3 = BandSegment.1.Ch1HoldbackVal Channel 1 holdback value float32 3acb 15051 Same as Programmer.SetUp.Ch1PVInputSegment.1.Ch1PVEvent Channel 1 PV event uint8 3ad4 15060 Not applicable0 = Off 1 = Absolute High 2 = Absolute Low3 = Deviation High 4 = Deviation Low 5 = Deviation BandSegment.1.Ch1PVEventUse Channel 1 PV event use (0 = Trigger; 1 = Alarm) bool 3ae2 15074 Not applicableSegment.1.Ch1PVEventVal Channel 1 PV event value float32 3ad6 15062 Same as Programmer.SetUp.Ch1PVInputSegment.1.Ch1Rate Channel 1 rate float32 3ac6 15046 Set by Programmer.SetUp.RateResolutionSegment.1.Ch1Time Channel 1 time time_t 3ac4 15044 Set by Network.Modbus.TimeFormatSegment.1.Ch1TSP Channel 1 target set-point float32 3ac2 15042 Same as Programmer.SetUp.Ch1PVInputSegment.1.Ch1UserVal Channel 1 user value float32 3ad8 15064 Same as Programmer.SetUp.ResetCh1UserValSegment.1.Ch1Wait Channel 1 Wait (Analogue 1 criterion) uint8 3ace 15054 Not applicable1= Abs high 2 = Abs low 3 = Dev high 4 = Dev LowSegment.1.Ch1WaitVal Channel 1 wait value float32 3ad0 15056 Same as Programmer.SetUp.PVWait1Segment.1.Ch2Holdback Channel 2 holdback type (as for Ch1Holdback, above) uint8 3aca 15050 Not applicableSegment.1.Ch2HoldbackVal Channel 2 holdback value float32 3acc 15052 Same as Programmer.SetUp.Ch2PVInputSegment.1.Ch2PVEvent Channel 2 PV event (as for Ch1PVEvent, above) uint8 3ad5 15061 Not applicableSegment.1.Ch2PVEventUse Channel 2 PV event use (as for Ch1PVEventUse, above) bool 3ae3 15075 Not applicableSegment.1.Ch2PVEventVal Channel 2 PV event value float32 3ad7 15063 Same as Programmer.SetUp.Ch2PVInputSegment.1.Ch2Rate Channel 2 rate float32 3ac7 15047 Set by Programmer.SetUp.RateResolutionSegment.1.Ch2Time Channel 2 time time_t 3ac5 15045 Set by Network.Modbus.TimeFormatSegment.1.Ch2TSP Channel 2 target set-point float32 3ac3 15043 Same as Programmer.SetUp.Ch2PVInputSegment.1.Ch2UserVal Channel 2 user value float32 3ad9 15065 Same as Programmer.SetUp.ResetCh2UserValSegment.1.Ch2Wait Channel 2 Wait (analogue 2 criterion; as for Ch1Wait, above) uint8 3acf 15055 Not applicableSegment.1.Ch2WaitVal Channel 2 wait value float32 3ad1 15057 Same as Programmer.SetUp.PVWait2Segment.1.Cycles Cycles (0 = Continuous) int16 3ad3 15059 Not applicableSegment.1.Duration Duration time_t 3ac1 15041 Set by Network.Modbus.TimeFormatSegment.1.EndType End type (0 = Dwell; 1 = Reset) uint8 3ac8 15048 Not applicableSegment.1.Event1 Event 1 (0 = Off; 1 = On) bool 3ada 15066 Not applicableSegment.1.Event2 Event 2 (0 = Off; 1 = On) bool 3adb 15067 Not applicableSegment.1.Event3 Event 3 (0 = Off; 1 = On) bool 3adc 15068 Not applicableSegment.1.Event4 Event 4 (0 = Off; 1 = On) bool 3add 15069 Not applicableSegment.1.Event5 Event 5 (0 = Off; 1 = On) bool 3ade 15070 Not applicableSegment.1.Event6 Event 6 (0 = Off; 1 = On) bool 3adf 15071 Not applicableSegment.1.Event7 Event 7 (0 = Off; 1 = On) bool 3ae0 15072 Not applicableSegment.1.Event8 Event 8 (0 = Off; 1 = On) bool 3ae1 15073 Not applicableSegment.1.GoBackTo Go back to uint8 3ad2 15058 Not applicableSegment.1.SegmentName Segment name string_t 6ad0 27344 Not applicableSegment.1.Type Type uint8 3ac0 15040 Not applicable0 = End 1 = Ramp 2 = Dwell3 = Step 4 = Wait 5 = GoBackSegment.1.WaitFor Wait for uint8 3acd 15053 Not applicable0 = Digital High 1 = Wait analogue 12 = Wait analogue 2 3 = Wait analogue 1 and analogue 2Segment.2.Ch1Holdback Channel 1 holdback type uint8 3af9 15097 Not applicableSegment.2.Ch1HoldbackVal Channel 1 holdback value float32 3afb 15099 Same as Programmer.SetUp.Ch1PVInputSegment.2.Ch1PVEvent Channel 1 PV event uint8 3b04 15108 Not applicableSegment.2.Ch1PVEventUse Channel 1 PV event use bool 3b12 15122 Not applicableSegment.2.Ch1PVEventVal Channel 1 PV event value float32 3b06 15110 Same as Programmer.SetUp.Ch1PVInputSegment.2.Ch1Rate Channel 1 rate float32 3af6 15094 Set by Programmer.SetUp.RateResolutionSegment.2.Ch1Time Channel 1 time time_t 3af4 15092 Set by Network.Modbus.TimeFormatSegment.2.Ch1TSP Channel 1 target set-point float32 3af2 15090 Same as Programmer.SetUp.Ch1PVInputSegment.2.Ch1UserVal Channel 1 user value float32 3b08 15112 Same as Programmer.SetUp.ResetCh1UserValFor parameterSegment.2.Ch1Wait Channel 1 Wait uint8 3afe 15102 Not applicableSegment.2.Ch1WaitVal Channel 1 wait value values and settings float32 3b00 15104 Same as Programmer.SetUp.PVWait1Segment.2.Ch2Holdback Channel 2 holdback type(enumerations),uint8 3afa 15098 Not applicableSegment.2.Ch2HoldbackVal Channel 2 holdback value float32 3afc 15100 Same as Programmer.SetUp.Ch2PVInputSegment.2.Ch2PVEvent Channel 2 PV event see Segment 1uint8 3b05 15109 Not applicableSegment.2.Ch2PVEventUse Channel 2 PV event use bool 3b13 15123 Not applicableSegment.2.Ch2PVEventVal Channel 2 PV event value float32 3b07 15111 Same as Programmer.SetUp.Ch2PVInputSegment.2.Ch2Rate Channel 2 rate float32 3af7 15095 Set by Programmer.SetUp.RateResolutionSegment.2.Ch2Time Channel 2 time time_t 3af5 15093 Set by Network.Modbus.TimeFormatSegment.2.Ch2TSP Channel 2 target set-point float32 3af3 15091 Same as Programmer.SetUp.Ch2PVInputSegment.2.Ch2UserVal Channel 2 user value float32 3b09 15113 Same as Programmer.SetUp.ResetCh2UserValSegment.2.Ch2Wait Channel 2 Wait uint8 3aff 15103 Not applicableSegment.2.Ch2WaitVal Channel 2 wait value float32 3b01 15105 Same as Programmer.SetUp.PVWait2Segment.2.Cycles Cycles int16 3b03 15107 Not applicableSegment.2.Duration Duration time_t 3af1 15089 Set by Network.Modbus.TimeFormatSegment.2.EndType End type uint8 3af8 15096 Not applicableSegment.2.Event1 Event 1 bool 3b0a 15114 Not applicablePage 221HA030554Issue 7 Nov 12
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183: nanodac RECORDER/CONTROLLER: USER G
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?