User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDE4.2 NETWORK MENUNetworkInterface(Section 4.2.1)MAC addressClient IdentifierIP typeIP addressSubnet maskGatewayArchiving(Section 4.2.2)Media sizeMedia freeMedia durationRateDestinationFile formatOn media fullRemote pathPrimary serverPrimary userPrimary passwordSecondary serverSecondary userSecondary passwordTriggerPeriodFTP Server(Section 4.2.3)User namePasswordModbus(Section 4.2.4)Prefmaster IPAddressInput timeoutUnit ID EnableSerial ModeTime FormatPref Master ConnResponse timeMaster Conn 2Response timeMaster Conn 3Response timeMaster Conn 4Response time4.2.1 InterfaceThis area of configuration allows the user to set up an IP address for the instrument, either by typing one in(Fixed), or automatically (DHCP), assuming a DHCP server is running.Network.InterfaceMACClient identifierIP TypeIP AddressSubnet MaskGateway00:0A:8D:01:90:0001000A8D019000DHCP123.123.123.123255.255.248.0234.234.234.234Figure 4.2.1 Network Interface menuMACRead only. Media Access Control. A unique address for each instrument, entered atthe factory.Client Identifier The client identifier is a unique id used by DHCP servers that implement option 61.Each nano product will have a unique ID built up from its MAC address. If the DHCPserver is configured to use option 61, then it will use this id instead of the MAC addressto assign a dynamic IP address.IP TypeIf ‘Fixed’, the user needs to enter an IP address and Subnet Mask in the following fields,and a Gateway address if required.If ‘DHCP’ the subsequent fields become read only, with the entries automatically generatedby the DHCP server. When set to DHCP, it takes several seconds before the IPaddress is obtained from the DHCP server.IP Address Read only if ‘IP Type’ = ‘DHCP’.If ‘IP Type’ = ‘Fixed’, the user may enter an IP address (IPV4 dot notation). This wouldnormally be supplied by the user’s IT department, or from the Network supervisor.Subnet Mask Read only if ‘IP Type’ = ‘DHCP’.If ‘IP Type’ = ‘Fixed’, this sets a range of IP addresses that can be accessed. Normallysupplied by the user’s IT department, or from the Network supervisor.Page 72HA030554Issue 7 Nov 12
nanodac RECORDER/CONTROLLER: USER GUIDE4.2.1 Interface (Cont.)GatewayRead only if ‘IP Type’ = ‘DHCP’.If ‘IP Type’ = ‘Fixed’ this allows the user to enter a gateway address for use when the unitis to communicate outside the local network. Normally supplied by the user’s IT department,or from the Network supervisor.4.2.2 ArchivingThis area of configuration is used to set up the parameters for use during unattended archiving. Some ofthe fields appear only if other fields are set to a particular value. For example, the CSV fields appear only if‘File Format’ is set to ‘CSV’ or to ‘Both’.The archived data is not removed from the flash memory of the instrument. When the flash memory is full,new data causes the oldest file(s) to be discarded.Note: For remote archiving, the host computer must be set up to respond to ‘pings’. This isbecause the nano pings the host whilst establishing connection, and if it does not receive a responsethe archive attempt fails.Network.ArchivingNetwork.ArchivingMedia SizeMedia FreeMedia DurationRateDestinationFile FormatOn Media Full1907.46 MB1902.90 MB763.77 DaysAutomaticFTP serverBinary (UHH)OverwriteRateDestinationFile FormatCSV ValuesCSV MessagesCSV HeadersCSV HeadingsMonthlyUSBBothYesNoNoYesRemote Path /archivePrimary Server 123.123.123.123Primary User historyPrimary Password ******Sec. Server 234.234.234.234Sec. User anonymousSec. Password ****Trigger NoPeriod NoneRemote with Binary file formatCSV Date FormatCSV Tab DelOn Media FullRemote PathPrimary ServerPrimary UserPrimary PasswordSec. ServerSec. UserSec. PasswordTriggerPeriodTextNoOverwrite/archive123.123.123.123history******234.234.234.234anonymous****NoNoneLocal with CSV files includedFigure 4.2.2a Unattended Archive configuration (typical settings)Media SizeMedia FreeMedia DurationHA030554Issue 7 Nov 12Appears only for File Format = ‘Binary (UHH)’. A read only value showing the capacityof the memory stick inserted in the USB port at the rear of the unit. Shows zero if nomemory stick is present.Appears only for File Format = ‘Binary (UHH)’. A read only value showing the space remainingin the memory stick inserted in the USB port at the rear of the unit. Shows zeroif no memory stick is present.Appears only for File Format = ‘Binary (UHH)’. A read only value showing the time it willtake to fill the Memory stick if the recorder configuration remains unchanged.Page 73
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35: nanodac RECORDER/CONTROLLER: USER G
Page 58: nanodac RECORDER/CONTROLLER: USER G
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?