User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLgc2.5.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f17 12055 Not applicableLgc2.5.In1 Input Value 1 float32 2f15 12053 0dpLgc2.5.In2 Input Value 2 float32 2f16 12054 0dpLgc2.5.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f18 12056 Not applicableLgc2.5.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f14 12052 Not applicableLgc2.5.Out The result of the logic operation (as Lgc2.1.Out) bool 2f19 12057 Not applicableLgc2.5.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f1a 12058 Not applicableLgc2.6.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f1e 12062 Not applicableLgc2.6.In1 Input Value 1 float32 2f1c 12060 0dpLgc2.6.In2 Input Value 2 float32 2f1d 12061 0dpLgc2.6.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f1f 12063 Not applicableLgc2.6.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f1b 12059 Not applicableLgc2.6.Out The result of the logic operation (as Lgc2.1.Out) bool 2f20 12064 Not applicableLgc2.6.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f21 12065 Not applicableLgc2.7.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f25 12069 Not applicableLgc2.7.In1 Input Value 1 float32 2f23 12067 0dpLgc2.7.In2 Input Value 2 float32 2f24 12068 0dpLgc2.7.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f26 12070 Not applicableLgc2.7.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f22 12066 Not applicableLgc2.7.Out The result of the logic operation (as Lgc2.1.Out) bool 2f27 12071 Not applicableLgc2.7.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f28 12072 Not applicableLgc2.8.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f2c 12076 Not applicableLgc2.8.In1 Input Value 1 float32 2f2a 12074 0dpLgc2.8.In2 Input Value 2 float32 2f2b 12075 0dpLgc2.8.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f2d 12077 Not applicableLgc2.8.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f29 12073 Not applicableLgc2.8.Out The result of the logic operation (as Lgc2.1.Out) bool 2f2e 12078 Not applicableLgc2.8.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f2f 12079 Not applicableLgc2.9.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f33 12083 Not applicableLgc2.9.In1 Input Value 1 float32 2f31 12081 0dpLgc2.9.In2 Input Value 2 float32 2f32 12082 0dpLgc2.9.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f34 12084 Not applicableLgc2.9.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f30 12080 Not applicableLgc2.9.Out The result of the logic operation (as Lgc2.1.Out) bool 2f35 12085 Not applicableLgc2.9.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f36 12086 Not applicableLgc2.10.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f3a 12090 Not applicableLgc2.10.In1 Input Value 1 float32 2f38 12088 0dpLgc2.10.In2 Input Value 2 float32 2f39 12089 0dpLgc2.10.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f3b 12091 Not applicableLgc2.10.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f37 12087 Not applicableLgc2.10.Out The result of the logic operation (as Lgc2.1.Out) bool 2f3c 12092 Not applicableLgc2.10.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f3d 12093 Not applicableLgc2.11.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f41 12097 Not applicableLgc2.11.In1 Input Value 1 float32 2f3f 12095 0dpLgc2.11.In2 Input Value 2 float32 2f40 12096 0dpLgc2.11.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f42 12098 Not applicableLgc2.11.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f3e 12094 Not applicableLgc2.11.Out The result of the logic operation (as Lgc2.1.Out) bool 2f43 12099 Not applicableLgc2.11.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f44 12100 Not applicableLgc2.12.FallbackType Fallback Condition (as Lgc2.1.FallbackType) uint8 2f48 12104 Not applicableLgc2.12.In1 Input Value 1 float32 2f46 12102 0dpLgc2.12.In2 Input Value 2 float32 2f47 12103 0dpLgc2.12.Invert Sense of Input Value (as Lgc2.1.Invert) uint8 2f49 12105 Not applicableLgc2.12.Oper Logic Operation (as Lgc2.1.Oper) uint8 2f45 12101 Not applicableLgc2.12.Out The result of the logic operation (as Lgc2.1.Out) bool 2f4a 12106 Not applicableLgc2.12.OutputStatus Output Status (0 = Good; 1 = Bad) uint8 2f4b 12107 Not applicableLgc8.1.In1 Input 1 Value (0 = Off; 1 = On) bool 2f4f 12111 Not applicableLgc8.1.In2 Input 2 Value (0 = Off; 1 = On) bool 2f50 12112 Not applicableLgc8.1.In3 Input 3 Value (0 = Off; 1 = On) bool 2f51 12113 Not applicableLgc8.1.In4 Input 4 Value (0 = Off; 1 = On) bool 2f52 12114 Not applicableLgc8.1.In5 Input 5 Value (0 = Off; 1 = On) bool 2f53 12115 Not applicableLgc8.1.In6 Input 6 Value (0 = Off; 1 = On) bool 2f54 12116 Not applicableLgc8.1.In7 Input 7 Value (0 = Off; 1 = On) bool 2f55 12117 Not applicableHA030554Issue 7 Nov 12Page 198
nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLgc8.1.In8 Input 8 Value (0 = Off; 1 = On) bool 2f56 12118 Not applicableLgc8.1.InInvert Invert Selected Inputs (See also section 4.20.3) uint8 2f4d 12109 Not applicableHex0001 = Invert input 1 Hex0010 = invert input 5Hex0002 = Invert input 2 Hex0020 = invert input 6Hex0003 = Invert input 3 Hex0030 = invert input 7Hex0004 = invert input 4 Hex0040 = invert input 8Lgc8.1.NumIn Number of Inputs uint8 2f4e 12110 Not applicableLgc8.1.Oper Logic Operation (0 = Off; 1 = AND; 2 = OR; 3 = XOR) uint8 2f4c 12108 Not applicableLgc8.1.Out Output Value (0 = Off (false); 1 = On (true)) bool 2f57 12119 Not applicableLgc8.1.OutInvert Invert the Output (0 = No; 1 = Yes) bool 2f58 12120 Not applicableLgc8.2.In1 Input 1 Value (0 = Off; 1 = On) bool 2f5c 12124 Not applicableLgc8.2.In2 Input 2 Value (0 = Off; 1 = On) bool 2f5d 12125 Not applicableLgc8.2.In3 Input 3 Value (0 = Off; 1 = On) bool 2f5e 12126 Not applicableLgc8.2.In4 Input 4 Value (0 = Off; 1 = On) bool 2f5f 12127 Not applicableLgc8.2.In5 Input 5 Value (0 = Off; 1 = On) bool 2f60 12128 Not applicableLgc8.2.In6 Input 6 Value (0 = Off; 1 = On) bool 2f61 12129 Not applicableLgc8.2.In7 Input 7 Value (0 = Off; 1 = On) bool 2f62 12130 Not applicableLgc8.2.In8 Input 8 Value (0 = Off; 1 = On) bool 2f63 12131 Not applicableLgc8.2.InInvert Invert Selected Inputs (as Lgc8.1.InInvert) uint8 2f5a 12122 Not applicableLgc8.2.NumIn Number of Inputs uint8 2f5b 12123 Not applicableLgc8.2.Oper Logic Operation (0 = Off; 1 = AND; 2 = OR; 3 = XOR) uint8 2f59 12121 Not applicableLgc8.2.Out Output Value (as Lgc8.1.Out) bool 2f64 12132 Not applicableLgc8.2.OutInvert Invert the Output (0 = No; 1 = Yes) bool 2f65 12133 Not applicableLoop.1.Diag.DerivativeOutContrib Derivative Output Contribution float32 0212 530 0dpLoop.1.Diag.Error Calculated error float32 020d 525 Same as Loop.1.Main.PVLoop.1.Diag.IntegralOutContrib Integral Output Contribution float32 0211 529 0dpLoop.1.Diag.LoopBreakAlarm Loop Break (0 = No break; 1 = Break) bool 020f 527 Not applicableLoop.1.Diag.LoopMode Mode of the Loop (0 = Auto; 1 = Man; 2 = Off) uint8 1691 5777 Not applicableLoop.1.Diag.PropOutContrib Proportional Output Contribution float32 0210 528 0dpLoop.1.Diag.SBrk Sensor Break Status ( 0 = No break; 1 = Break) bool 0213 531 Not applicableLoop.1.Diag.SchedCBH The Scheduled Cutback High (0 = Auto) float32 1695 5781 0dpLoop.1.Diag.SchedCBL The Scheduled Cutback Low (0 = Auto) float32 1696 5782 0dpLoop.1.Diag.SchedLPBrk The Scheduled Loop Break Time (0 = Off) float32 1698 5784 0dpLoop.1.Diag.SchedMR The Scheduled Manual Reset float32 1697 5783 1dpLoop.1.Diag.SchedOPHi The Scheduled Output High Limit float32 169a 5786 1dpLoop.1.Diag.SchedOPLo The Scheduled Output Low Limit float32 169b 5787 1dpLoop.1.Diag.SchedPB The Scheduled Proportional Band float32 1692 5778 1dpLoop.1.Diag.SchedR2G The Scheduled Relative Cool Gain float32 1699 5785 1dpLoop.1.Diag.SchedTd The Scheduled Derivative Time (0 = Off) float32 1694 5780 0dpLoop.1.Diag.SchedTi The Scheduled Integral Time (0 = Off) float32 1693 5779 0dpLoop.1.Diag.TargetOutVal Target Output value float32 020e 526 Same as Loop.1.OP.OutputHighLimitLoop.1.Diag.WrkOPHi Working Output High Limit float32 0215 533 0dpLoop.1.Diag.WrkOPLo Working Output Low Limit float32 0214 532 0dpLoop.1.Main.ActiveOut Working Output float32 0204 516 Same as Loop.1.OP.OutputHighLimitLoop.1.Main.AutoMan Auto/Manual Mode (0 = Auto; 1 = Man) bool 0201 513 Not applicableLoop.1.Main.Inhibit Control Inhibit (0 = No; 1 = Yes) bool 0205 517 Not applicableLoop.1.Main.IntHold Integral action inhibit. 0 = No; 1 = Yes uint8 0206 518 Not applicableLoop1.Maim.PV Process varaible float32 0200 512 1dpLoop.1.Main.TargetSP Target Setpoint float32 0202 514 Same as Loop.1.Main.PVLoop.1.Main.WorkingSP Working Setpoint float32 0203515 Same as Loop.1.Main.PVLoop.1.OP.Ch1OnOffHysteresis Ch1 On/Off Hysteresis in Engineering Units float32 1672 5746 Same as Loop.1.Main.PVLoop.1.OP.Ch1Out Channel 1 Output Value float32 020b 523 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch1PotBreak Ch1 Potentiometer Break (0 = Off; 1 = On) uint8 1679 5753 Not applicableLoop.1.OP.Ch1PotPosition Ch1 Valve Position float32 1678 5752 0dpLoop.1.OP.Ch1TravelTime Channel 1 Travel Time float32 1674 5748 1dpLoop.1.OP.Ch2Deadband Channel 2 Deadband float32 166f 5743 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch2OnOffHysteresis Ch2 On/Off Hysteresis in Eng Units float32 1673 5747 Same as Loop.1.Main.PVLoop.1.OP.Ch2Out Channel 2 (Cool) Output Value float32 020c 524 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch2PotBreak Ch2 Potentiometer Break (0 = Off; 1 = On) uint8 167b 5755 Not applicableLoop.1.OP.Ch2PotPosition Ch2 Valve Position float32 167a 5754 0dpLoop.1.OP.Ch2TravelTime Channel 2 Travel Time float32 1675 5749 1dpLoop.1.OP.CoolType Cooling Algorithm Type uint8 1683 5763 Not applicable0 = Linear 1 = Oil 2 = Water 3 = FanLoop.1.OP.EnablePowerFeedforward 0 = Power Feedforward disabled; 1 = PFF enabled uint8 1681 5761 Not applicableLoop.1.OP.FeedForwardGain Feedforward Gain float32 1685 5765 3dpLoop.1.OP.FeedForwardOffset Feedforward Offset float32 1686 5766 0dpLoop.1.OP.FeedForwardTrimLimit Feedforward Trim Limit float32 1687 5767 0dpLoop.1.OP.FeedForwardType Feedforward Type (0 = None; 1 = Remote; 2 = SP; 3 = PV) uint8 1684 5764 Not applicableLoop.1.OP.FeedForwardVal Feedforward Value float32 1688 5768 0dpLoop.1.OP.FF_Rem Remote Feed Forward Input float32 168d 5773 0dpLoop.1.OP.ForcedOP Forced manual output value float32 168f 5775 1dpLoop.1.OP.ManStartup Manual Startup Mode (0 = Off; 1 = On) bool 1690 5776 Not applicableLoop.1.OP.ManualMode Manual Output Mode (0 = Track; 1 = Step; 2 = Last MOP) uint8 167f 5759 Not applicableLoop.1.OP.ManualOutVal Manual Output Value float32 1680 5760 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.MeasuredPower Measured Mains Voltage float32 1682 5762 0dpLoop.1.OP.NudgeLower Valve Nudge Lower (1 = Lower) uint8 1677 5751 Not applicableLoop.1.OP.NudgeRaise Valve Nudge Raise (1 = Raise) uint8 1676 5750 Not applicablePage 199HA030554Issue 7 Nov 12
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161: nanodac RECORDER/CONTROLLER: USER G
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

Create successful ePaper yourself

Delete template?

Save as template?