User Guide - Eurotherm Ltda

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionChannel.3.Alarm2.Inactive 1 = alarm source safe and ack’d (if necessary) bool 196e 6510 Not applicableChannel.3.Alarm2.Inhibit 1 = Alarm inhibited bool 1971 6513 Not applicableChannel.3.Alarm2.Latch Alarm latch type (as for Channel.1.Alarm1) uint8 1961 6497 Not applicableChannel.3.Alarm2.NotAcknowledged 1 = alarm has not been acknowledged bool 196f 6511 Not applicableChannel.3.Alarm2.Reference Deviation alarm ‘Reference’ value float32 1966 6502 Same as Channel.3.Main.PVChannel.3.Alarm2.Status Alarm status (as for Channel.1.Alarm1) uint8 010b 267 Not applicableChannel.3.Alarm2.Threshold Alarm trigger threshold float32 1963 6499 Same as Channel.3.Main.PVChannel.3.Alarm2.Type Alarm type (as for Channel.1.Alarm1) uint8 1960 6496 Not applicableChannel.3.Main.CJType Cold junction compensation type (as for Channel.1.Main) uint8 190c 6412 Not applicableChannel.3.Main.CloseString Close String string_t 49a2 18850 Not applicableChannel.3.Main.Descriptor Text string to describe the channel string_t 4936 18742 Not applicableChannel.3.Main.ExtCJTemp External CJ temperature float32 190d 6413 1dpChannel.3.Main.FaultResponse Input fault response (As for Channel.1.Main) uint8 1910 6416 Not applicableChannel.3.Main.Filter Filter time constant float32 190e 6414 1dpChannel.3.Main.InputHigh Input range maximum value float32 1904 6404 1dpChannel.3.Main.InputLow Input range minimum value float32 1903 6403 1dpChannel.3.Main.InternalCJTemp Channel internal cold junction temperature float32 1915 6421 1dpChannel.3.Main.IPAdjustState Input Adjust state (0 = Unadjusted; 1 = Adjusted) bool 1916 6422 Not applicableChannel.3.Main.IPAdjustState2 Secondary Input Adjust state (0 = Unadjusted; 1 = Adjusted) bool 191c 6428 Not applicableChannel.3.Main.LinType Linearisation type (as for Channel.1.Main.LinType) uint8 1906 6406 Not applicableChannel.3.Main.MeasuredValue Input value before linearisation, scaling, adjust etc. float32 1914 6420 Set by Channel.3.Main.ResolutionChannel.3.Main.MeasuredValue2 Measured value of the secondary input float32 1919 6425 Set by Channel.3.Main.ResolutionChannel.3.Main.Offset Input offset float32 1917 6423 3dpChannel.3.Main.Offset2 Secondary input offset float32 1918 6424 3dpChannel.3.Main.OpenString Open String string_t 497e 18814 Not applicableChannel.3.Main.PV The output (displayed) value of the channel. float32 0108 264 Set by Channel.3.Main.ResolutionChannel.3.Main.PV2 The secondary input process variable (output) of the channel float32 0118 280 Set by Channel.3.Main.ResolutionChannel.3.Main.RangeHigh Range high value float32 1908 6408 Set by Channel.3.Main.ResolutionChannel.3.Main.RangeLow Range low value float32 1907 6407 Set by Channel.3.Main.ResolutionChannel.3.Main.RangeUnits Range units uint8 1909 6409 Not applicableChannel.3.Main.Resolution Specifies the resolution/number of decimal places uint8 1901 6401 Not applicableChannel.3.Main.ScaleHigh Scale high value float32 190b 6411 Set by Channel.3.Main.ResolutionChannel.3.Main.ScaleHigh2 Scale high value for the secondary input float32 191b 6427 Set by Channel.3.Main.ResolutionChannel.3.Main.ScaleLow Scale low value float32 190a 6410 Set by Channel.3.Main.ResolutionChannel.3.Main.ScaleLow2 Scale low value for the secondary input float32 191a 6426 Set by Channel.3.Main.ResolutionChannel.3.Main.SensorBreakType Sensor break type (as for Channel.1.Main) uint8 190f 6415 Not applicableChannel.3.Main.SensorBreakVal Sensor break value uint8 1911 6417 Not applicableChannel.3.Main.Shunt Shunt value in Ohms float32 1905 6405 2dpChannel.3.Main.Status Channel status (as for Channel.1.Main.Status) uint8 0109 265 Not applicableChannel.3.Main.Status2 The secondary input PV (output) status uint8 0119 281 Not applicableChannel.3.Main.TestSignal Channel test waveform (as for Channel.1.Main) uint8 1902 6402 Not applicableChannel.3.Main.Type Channel function (as for Channel.1.Main.Type) uint8 1900 6400 Not applicableChannel.3.Main.Units Units descriptor string_t 494b 18763 Not applicableChannel.3.Trend.Colour Trend colour (as for Channel.1.Trend.Colour) uint8 1920 6432 Not applicableChannel.3.Trend.SpanHigh Specifies the highest PV (output value) to be displayed float32 1922 6434 Same as Channel.3.Main.PVChannel.3.Trend.SpanLow Specifies the lowest PV (output value) to be displayed float32 1921 6433 Same as Channel.3.Main.PVChannel.4.Alarm1.Acknowledge 1 = acknowledge alarm bool 01b6 438 Not applicableChannel.4.Alarm1.Acknowledgement 1 = alarm acknowledged bool 19d0 6608 Not applicableChannel.4.Alarm1.Active 1 = alarm source active, or safe but not ack’d bool 19cb 6603 Not applicableChannel.4.Alarm1.Amount Rate-of-change alarm ‘Amount’ float32 19c8 6600 Same as Channel.4.Main.PVChannel.4.Alarm1.AverageTime Rate-of-change alarm ‘Average time’ time_t 19ca 6602 Set by Network.Modbus.TimeFormatChannel.4.Alarm1.Block 0 = Blocking alarms off; 1 = Blocking alarms on. uint8 19c2 6594 Not applicableChannel.4.Alarm1.ChangeTime Rate-of-change alarm ‘Change Time’ uint8 19c9 6601 Not applicableChannel.4.Alarm1.Deviation Deviation alarm ‘Deviation Value’ float32 19c7 6599 Same as Channel.4.Main.PVChannel.4.Alarm1.Dwell Alarm dwell time time_t 19c5 6597 Set by Network.Modbus.TimeFormatChannel.4.Alarm1.Hysteresis Alarm hysteresis value float32 19c4 6596 Same as Channel.4.Main.PVChannel.4.Alarm1.Inactive 1 = alarm source safe and ack’d (if necessary) bool 19ce 6606 Not applicableChannel.4.Alarm1.Inhibit 1 = alarm inhibited bool 19d1 6609 Not applicableChannel.4.Alarm1.Latch Alarm latch type (as for Channel.1.Alarm1) uint8 19c1 6593 Not applicableChannel.4.Alarm1.NotAcknowledged 1 = alarm has not been acknowledged bool 19cf 6607 Not applicableChannel.4.Alarm1.Reference Deviation alarm ‘Reference’ value float32 19c6 6598 Same as Channel.4.Main.PVChannel.4.Alarm1.Status Alarm status (as for Channel.1.Alarm1) uint8 010e 270 Not applicableChannel.4.Alarm1.Threshold Alarm trigger threshold float32 19c3 6595 Same as Channel.4.Main.PVChannel.4.Alarm1.Type Alarm type (as for Channel.1.Alarm1) uint8 19c0 6592 Not applicableChannel.4.Alarm2.Acknowledge 1 = acknowledge alarm bool 01b7 439 Not applicableChannel.4.Alarm2.Acknowledgement 1 = alarm acknowledged bool 19f0 6640 Not applicableChannel.4.Alarm2.Active 1 = alarm source active, or safe but not ack’d bool 19eb 6635 Not applicableChannel.4.Alarm2.Amount Rate-of-change alarm ‘Amount’ float32 19e8 6632 Same as Channel.4.Main.PVChannel.4.Alarm2.AverageTime Rate-of-change alarm ‘Average time’ time_t 19ea 6634 Set by Network.Modbus.TimeFormatChannel.4.Alarm2.Block 0 = Blocking alarms off; 1 = Blocking alarms on uint8 19e2 6626 Not applicableChannel.4.Alarm2.ChangeTime Rate-of-change alarm ‘Change Time’ uint8 19e9 6633 Not applicableChannel.4.Alarm2.Deviation Deviation alarm ‘Deviation Value’ float32 19e7 6631 Same as Channel.4.Main.PVChannel.4.Alarm2.Dwell Alarm dwell time time_t 19e5 6629 Set by Network.Modbus.TimeFormatChannel.4.Alarm2.Hysteresis Alarm hysteresis value float32 19e4 6628 Same as Channel.4.Main.PVChannel.4.Alarm2.Inactive 1 = alarm source safe and ack’d (if necessary) bool 19ee 6638 Not applicableChannel.4.Alarm2.Latch Alarm latch type (as for Channel.1.Alarm1) uint8 19e1 6625 Not applicableChannel.4.Alarm2.NotAcknowledged 1 = alarm has not been acknowledged bool 19ef 6639 Not applicableChannel.4.Alarm2.Reference Deviation alarm ‘Reference’ value float32 19e6 6630 Same as Channel.4.Main.PVChannel.4.Alarm2.Status Alarm status (as for Channel.1.Alarm1) uint8 010f 271 Not applicableChannel.4.Alarm2.Threshold Alarm trigger threshold float32 19e3 6627 Same as Channel.4.Main.PVPage 185HA030554Issue 7 Nov 12