User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDE6.3.2 Wiring Editor Operating Details (Cont.)MONITORSMonitor points are added to a wiring diagram by click-dragging them from the Function Block tree onto thediagram. A monitor shows the current value (updated at the iTools parameter list update rate) of the parameterto which it is linked. By default the name of the parameter is shown. To hide the parameter name eitherdouble click on the monitor box or ‘Show Names’ in the context (right-click) menu can be used to toggle theparameter name on and off.Monitors are linked to function blocks and wires by clicking on the chain icon at the bottom right-hand cornerof the box and then clicking again on the required parameter. A dashed line is drawn to the top of theblock or the selected wire segment.Note: Once the monitor has been linked, the Chain icon disappears. It re-appears when the mousecursor is hovered over the bottom right-hand corner of the monitor box.Monitor Context MenuShow namesUnlinkCutCopyPasteDeleteUndeleteBring to FrontPush to BackParameter HelpFigure 6.3.2f Comment and Monitor appearanceToggles parameter names on and off in the monitor box.Deletes the current link from the monitor.Moves the monitor to the Clipboard, ready to be pasted elsewhere.Short cut = +.Copies the monitor from the wiring diagram to the Clipboard,ready to be pasted elsewhere. Short cut = +.Copies a monitor from the Clipboard to the wiring diagram.Short cut = +.Marks the monitor for deletion at next download.Undoes the Delete command if download has not taken placesince.Moves the item to the ‘top’ layer of the diagram.Moves the item to the ‘bottom’ layer of the diagram.Shows parameter help for the item.Figure 6.3.2gMonitor context menuDOWNLOADINGWhen the wiring editor is opened the current wiring and diagram layout is read from the instrument. Nochanges are made to the instrument function block execution or wiring until the download button is pressed.Any changes made using the operator interface after the editor is opened are lost on download.When a block is dropped onto the diagram, instrument parameters are changed to make the parameters forthat block available. If changes are made and the editor is closed without saving them there is a delay whilethe editor clears these parameters.During download, the wiring is written to the instrument which then calculates the block execution order andstarts executing the blocks. The diagram layout including comments and monitors is then written into instrumentflash memory along with the current editor settings. When the editor is reopened, the diagram isshown positioned as it was when it was last downloaded.Page 268HA030554Issue 7 Nov 12
nanodac RECORDER/CONTROLLER: USER GUIDE6.3.2 Wiring Editor Operating Details (Cont.)COLOURSItems on the diagram are coloured as follows:RedItems which totally or partially obscure other items and items which are totally or partiallyobscured by other items. Wires that are connected to unalterable or non-availableparameters. Execution breaks.BlueNon-available parameters in function blocks.GreenItems added to the diagram since last download are shown as green dashed lines.MagentaAll selected items, or any item over which the cursor is hovering.PurpleRed wires when being hovered over by the mouse cursor.BlackAll items added to the diagram before the last download. Redundant execution breaks.Monitor and comment text.DIAGRAM CONTEXT MENUCutActive only when the right click occurs within the boundingrectangle which appears when more than one item is selected.Moves the selection off the diagram to the Clipboard.Short cut = +.CopyAs for ‘Cut’, but the selection is copied, leaving the originalon the diagram. Short cut = +.PasteCopies the contents of the Clipboard to the diagram. Shortcut = +.Re-Route wires Reroutes all selected wires. If no wires are selected, allwires are re-routed.Align Tops Aligns the tops of all blocks in the selected area.Align Lefts Aligns the left edges of all blocks in the selected area.Space Evenly Spaces selected items such that their top left corners arespaced evenly across the width of the diagram. Click onthe item which is to be the left-most item, then+ the remaining items in the order inwhich they are to appear.DeleteMarks the item for deletion at next download time.Can be ‘Undeleted’ up until download occurs.Figure 6.3.2hUndeleteReverses the action of ‘Delete’ on the selected item.Diagram context menuSelect AllSelects all items on the current diagram.Create Compound Active only when the right click occurs, in the top level diagram, within the boundingrectangle which appears when more than one item is selected. Creates a new wiring diagramas described in ‘Compound’, below.RenameAllows a new name to entered for the current wiring diagram. This name appears in therelevant tab.Copy Graphic Copies the selected items (or the whole diagram if no items are selected) to the clipboardas a Windows metafile, suitable for pasting into a documentation application.Wiring entering/leaving the selection (if any) are drawn in tag mode.Save Graphic... As for ‘Copy Graphic’ above, but saves to a user-specified file location instead of theclipboard.Copy Fragment To File...Copies selected items to a user-named file in folder ‘My iTools Wiring Fragments’ locatedin ‘My Documents’.Paste Fragment From FileAllows the user to select a stored fragment for inclusion in the wiring diagram.CentrePlaces the display window at the centre of the selected items. If ‘Select All’ has previouslybeen clicked-on, then the display widow is placed over the centre of the diagram.HA030554Issue 7 Nov 12Page 269
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231: nanodac RECORDER/CONTROLLER: USER G
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?