User Guide - Eurotherm Ltda

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLoop.1.SP.SPIntBal SP Integral Balance (0 = Off; 1 = On) bool 166b 5739 Not applicableLoop.1.SP.SPLowLimit Setpoint Low Limit float32 165f 5727 Same as Loop.1.Main.PVLoop.1.SP.SPSelect Active Setpoint Select (0 = SP1; 1 = SP2) uint8 165b 5723 Not applicableLoop.1.SP.SPTrack Enables setpoint tracking (0 = Off; 1 = On) uint8 1668 5736 Not applicableLoop.1.SP.SPTrim Setpoint Trim value float32 1664 5732 Same as Loop.1.Main.PVLoop.1.SP.SPTrimHighLimit Setpoint Trim High Limit float32 1665 5733 Same as Loop.1.Main.PVLoop.1.SP.SPTrimLowLimit Setpoint Trim Low Limit float32 1666 5734 Same as Loop.1.Main.PVLoop.1.SP.TrackPV Track PV float32 1669 5737 Same as Loop.1.Main.PVLoop.1.SP.TrackSP Manual Tracking Value float32 166a 5738 Same as Loop.1.Main.PVLoop.1.Tune.Alpha Alpha float32 16ad 5805 4dpLoop.1.Tune.Alpha_p Alpha_p float32 16ab 5803 2dpLoop.1.Tune.AutotuneEnable Autotune Enable (0 = Autotune Off; 1 = on) bool 1631 5681 Not applicableLoop.1.Tune.CycleNo CycleNo float32 16af 5807 0dpLoop.1.Tune.Debug Debug float32 16ae 5806 2dpLoop.1.Tune.Diagnostics Tuning diagnostics bool 31cd 12749 Not applicableLoop.1.Tune.OPss OPss float32 16ac 5804 2dpLoop.1.Tune.OutputHighLimit Autotune High Output Power Limit float32 1632 5682 Same as Loop.1.OP.OutputHighLimitLoop.1.Tune.OutputLowLimit Autotune Low Output Power Limit float32 1633 5683 Same as Loop.1.OP.OutputHighLimitLoop.1.Tune.PBs PBs float32 16b0 5808 2dpLoop.1.Tune.Settle Settle float32 16b2 5810 2dpLoop.1.Tune.Stage Autotune stage uint8 0208 520 Not applicable0 = Reset 1 = None 2 = Monitor3 = Current SP 4 = NewSP 5 = ToSp6 = Max 7 = MinLoop.1.Tune.StageTime Time in this Stage of Tune float32 0209 521 0dpLoop.1.Tune.State Tune status uint8 0207 519 Not applicable0 = Off 1 = Ready 2 = Running3 = Complete 4 = Timeout 5 = Ti Limit6 = R2g limitLoop.1.Tune.TDs TDs float32 16b1 5809 2dpLoop.1.Tune.TuneR2G R2G Tuning Type uint8 1607 5639 Not applicableLoop.1.Tune.Tuning Tuning float32 16aa 5802 0dpLoop.1.Tune.Type Autotune Algorithm Type uint8 1630 5680 Not applicable(0 = Cycle; 1 = Single; 2 = Adaptive; 3 = R2GPD)Loop.2.Diag.DerivativeOutContrib Derivative Output Contribution float32 0292 658 0dpLoop.2.Diag.Error Calculated Error float32 028d 653 Same as Loop.2.Main.PVLoop.2.Diag.IntegralOutContrib Integral Output Contribution float32 0291 657 0dpLoop.2.Diag.LoopBreakAlarm Loop Break (0 = No break; 1 = Break) bool 028f 655 Not applicableLoop.2.Diag.LoopMode Loop mode (0 = Auto; 1 = Man; 2 = Off) uint8 1791 6033 Not applicableLoop.2.Diag.PropOutContrib Proportional Output Contribution float32 0290 656 0dpLoop.2.Diag.SBrk Sensor break status (0 = No break; 1 = Break) bool 0293 659 Not applicableLoop.2.Diag.SchedCBH The Scheduled Cutback Hi (0 = Auto) float32 1795 6037 0dpLoop.2.Diag.SchedCBL The Scheduled Cutback Lo (0 = Auto) float32 1796 6038 0dpLoop.2.Diag.SchedLPBrk The Scheduled Loop Break Time float32 1798 6040 0dpLoop.2.Diag.SchedMR The Scheduled Manual Reset float32 1797 6039 1dpLoop.2.Diag.SchedOPHi The Scheduled Output High Limit float32 179a 6042 1dpLoop.2.Diag.SchedOPLo The Scheduled Output Low Limit float32 179b 6043 1dpLoop.2.Diag.SchedPB The Scheduled Proportional Band float32 1792 6034 1dpLoop.2.Diag.SchedR2G The Scheduled Relative Cool Gain float32 1799 6041 1dpLoop.2.Diag.SchedTd The Scheduled Derivative Time (0 = Off) float32 1794 6036 0dpLoop.2.Diag.SchedTi The Scheduled Integral Time (0 = Off) float32 1793 6035 0dpLoop.2.Diag.TargetOutVal Target Output float32 028e 654 Same as Loop.2.OP.OutputHighLimitLoop.2.Diag.WrkOPHi Working Output Hi Limit float32 0295 661 0dpLoop.2.Diag.WrkOPLo Working Output Lo Limit float32 0294 660 0dpLoop.2.Main.ActiveOut Working Output float32 0284 644 Same as Loop.2.OP.OutputHighLimitLoop.2.Main.AutoMan Auto/Manual Mode (Mode. 0 = Auto; 1 = Man) bool 0281 641 Not applicableLoop.2.Main.Inhibit Control Inhibit (0 = No; 1 = Yes) bool 0285 645 Not applicableLoop.2.Main.IntHold Integral action inhibit. 0 = No; 1 = Yes uint8 0286 646 Not applicableLoop.2.Main.PV Process Variable value float32 0280 640 1dpLoop.2.Main.TargetSP Target Setpoint float32 0282 642 Same as Loop.2.Main.PVLoop.2.Main.WorkingSP Working Setpoint float32 0283 643 Same as Loop.2.Main.PVLoop.2.OP.Ch1OnOffHysteresis Channel 1 hysteresis in engineering units float32 1772 6002 Same as Loop.2.Main.PVLoop.2.OP.Ch1Out Channel 1 Output Value float32 028b 651 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.Ch1PotBreak Ch1 Potentiometer Break (0 = Off; 1 = On) uint8 1779 6009 Not applicableLoop.2.OP.Ch1PotPosition Ch1 Valve Position float32 1778 6008 0dpLoop.2.OP.Ch1TravelTime Channel 1 Travel Time float32 1774 6004 1dpLoop.2.OP.Ch2Deadband Channel 2 Deadband float32 176f 5999 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.Ch2OnOffHysteresis Channel 2 hysteresis in engineering units float32 1773 6003 Same as Loop.2.Main.PVLoop.2.OP.Ch2Out Channel 2 output value float32 028c 652 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.Ch2PotBreak Channel 2 Potentiometer Break (0 = Off; 1 = On) uint8 177b 6011 Not applicableLoop.2.OP.Ch2PotPosition Channel 2 Valve Position float32 177a 6010 0dpLoop.2.OP.Ch2TravelTime Channel 2 Travel Time float32 1775 6005 1dpLoop.2.OP.CoolType Cooling Algorithm Type uint8 1783 6019 Not applicable0 = Linear; 1 = Oil; 2 = Water; 3 = FanLoop.2.OP.EnablePowerFeedforward 0 = Power Feedforward disabled; 1 = PFF enabled uint8 1781 6017 Not applicableLoop.2.OP.FeedForwardGain Feedforward Gain float32 1785 6021 3dpLoop.2.OP.FeedForwardOffset Feedforward Offset float32 1786 6022 0dpLoop.2.OP.FeedForwardTrimLimit Feedforward Trim Limit float32 1787 6023 0dpLoop.2.OP.FeedForwardType Feedforward Type (0 = None; 1 = Remote; 2 = SP; 3 = PV) uint8 1784 6020 Not applicableLoop.2.OP.FeedForwardVal Feedforward Value float32 1788 6024 0dpPage 201HA030554Issue 7 Nov 12