User Guide - Eurotherm Ltda

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLgc8.1.In8 Input 8 Value (0 = Off; 1 = On) bool 2f56 12118 Not applicableLgc8.1.InInvert Invert Selected Inputs (See also section 4.20.3) uint8 2f4d 12109 Not applicableHex0001 = Invert input 1 Hex0010 = invert input 5Hex0002 = Invert input 2 Hex0020 = invert input 6Hex0003 = Invert input 3 Hex0030 = invert input 7Hex0004 = invert input 4 Hex0040 = invert input 8Lgc8.1.NumIn Number of Inputs uint8 2f4e 12110 Not applicableLgc8.1.Oper Logic Operation (0 = Off; 1 = AND; 2 = OR; 3 = XOR) uint8 2f4c 12108 Not applicableLgc8.1.Out Output Value (0 = Off (false); 1 = On (true)) bool 2f57 12119 Not applicableLgc8.1.OutInvert Invert the Output (0 = No; 1 = Yes) bool 2f58 12120 Not applicableLgc8.2.In1 Input 1 Value (0 = Off; 1 = On) bool 2f5c 12124 Not applicableLgc8.2.In2 Input 2 Value (0 = Off; 1 = On) bool 2f5d 12125 Not applicableLgc8.2.In3 Input 3 Value (0 = Off; 1 = On) bool 2f5e 12126 Not applicableLgc8.2.In4 Input 4 Value (0 = Off; 1 = On) bool 2f5f 12127 Not applicableLgc8.2.In5 Input 5 Value (0 = Off; 1 = On) bool 2f60 12128 Not applicableLgc8.2.In6 Input 6 Value (0 = Off; 1 = On) bool 2f61 12129 Not applicableLgc8.2.In7 Input 7 Value (0 = Off; 1 = On) bool 2f62 12130 Not applicableLgc8.2.In8 Input 8 Value (0 = Off; 1 = On) bool 2f63 12131 Not applicableLgc8.2.InInvert Invert Selected Inputs (as Lgc8.1.InInvert) uint8 2f5a 12122 Not applicableLgc8.2.NumIn Number of Inputs uint8 2f5b 12123 Not applicableLgc8.2.Oper Logic Operation (0 = Off; 1 = AND; 2 = OR; 3 = XOR) uint8 2f59 12121 Not applicableLgc8.2.Out Output Value (as Lgc8.1.Out) bool 2f64 12132 Not applicableLgc8.2.OutInvert Invert the Output (0 = No; 1 = Yes) bool 2f65 12133 Not applicableLoop.1.Diag.DerivativeOutContrib Derivative Output Contribution float32 0212 530 0dpLoop.1.Diag.Error Calculated error float32 020d 525 Same as Loop.1.Main.PVLoop.1.Diag.IntegralOutContrib Integral Output Contribution float32 0211 529 0dpLoop.1.Diag.LoopBreakAlarm Loop Break (0 = No break; 1 = Break) bool 020f 527 Not applicableLoop.1.Diag.LoopMode Mode of the Loop (0 = Auto; 1 = Man; 2 = Off) uint8 1691 5777 Not applicableLoop.1.Diag.PropOutContrib Proportional Output Contribution float32 0210 528 0dpLoop.1.Diag.SBrk Sensor Break Status ( 0 = No break; 1 = Break) bool 0213 531 Not applicableLoop.1.Diag.SchedCBH The Scheduled Cutback High (0 = Auto) float32 1695 5781 0dpLoop.1.Diag.SchedCBL The Scheduled Cutback Low (0 = Auto) float32 1696 5782 0dpLoop.1.Diag.SchedLPBrk The Scheduled Loop Break Time (0 = Off) float32 1698 5784 0dpLoop.1.Diag.SchedMR The Scheduled Manual Reset float32 1697 5783 1dpLoop.1.Diag.SchedOPHi The Scheduled Output High Limit float32 169a 5786 1dpLoop.1.Diag.SchedOPLo The Scheduled Output Low Limit float32 169b 5787 1dpLoop.1.Diag.SchedPB The Scheduled Proportional Band float32 1692 5778 1dpLoop.1.Diag.SchedR2G The Scheduled Relative Cool Gain float32 1699 5785 1dpLoop.1.Diag.SchedTd The Scheduled Derivative Time (0 = Off) float32 1694 5780 0dpLoop.1.Diag.SchedTi The Scheduled Integral Time (0 = Off) float32 1693 5779 0dpLoop.1.Diag.TargetOutVal Target Output value float32 020e 526 Same as Loop.1.OP.OutputHighLimitLoop.1.Diag.WrkOPHi Working Output High Limit float32 0215 533 0dpLoop.1.Diag.WrkOPLo Working Output Low Limit float32 0214 532 0dpLoop.1.Main.ActiveOut Working Output float32 0204 516 Same as Loop.1.OP.OutputHighLimitLoop.1.Main.AutoMan Auto/Manual Mode (0 = Auto; 1 = Man) bool 0201 513 Not applicableLoop.1.Main.Inhibit Control Inhibit (0 = No; 1 = Yes) bool 0205 517 Not applicableLoop.1.Main.IntHold Integral action inhibit. 0 = No; 1 = Yes uint8 0206 518 Not applicableLoop1.Maim.PV Process varaible float32 0200 512 1dpLoop.1.Main.TargetSP Target Setpoint float32 0202 514 Same as Loop.1.Main.PVLoop.1.Main.WorkingSP Working Setpoint float32 0203515 Same as Loop.1.Main.PVLoop.1.OP.Ch1OnOffHysteresis Ch1 On/Off Hysteresis in Engineering Units float32 1672 5746 Same as Loop.1.Main.PVLoop.1.OP.Ch1Out Channel 1 Output Value float32 020b 523 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch1PotBreak Ch1 Potentiometer Break (0 = Off; 1 = On) uint8 1679 5753 Not applicableLoop.1.OP.Ch1PotPosition Ch1 Valve Position float32 1678 5752 0dpLoop.1.OP.Ch1TravelTime Channel 1 Travel Time float32 1674 5748 1dpLoop.1.OP.Ch2Deadband Channel 2 Deadband float32 166f 5743 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch2OnOffHysteresis Ch2 On/Off Hysteresis in Eng Units float32 1673 5747 Same as Loop.1.Main.PVLoop.1.OP.Ch2Out Channel 2 (Cool) Output Value float32 020c 524 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.Ch2PotBreak Ch2 Potentiometer Break (0 = Off; 1 = On) uint8 167b 5755 Not applicableLoop.1.OP.Ch2PotPosition Ch2 Valve Position float32 167a 5754 0dpLoop.1.OP.Ch2TravelTime Channel 2 Travel Time float32 1675 5749 1dpLoop.1.OP.CoolType Cooling Algorithm Type uint8 1683 5763 Not applicable0 = Linear 1 = Oil 2 = Water 3 = FanLoop.1.OP.EnablePowerFeedforward 0 = Power Feedforward disabled; 1 = PFF enabled uint8 1681 5761 Not applicableLoop.1.OP.FeedForwardGain Feedforward Gain float32 1685 5765 3dpLoop.1.OP.FeedForwardOffset Feedforward Offset float32 1686 5766 0dpLoop.1.OP.FeedForwardTrimLimit Feedforward Trim Limit float32 1687 5767 0dpLoop.1.OP.FeedForwardType Feedforward Type (0 = None; 1 = Remote; 2 = SP; 3 = PV) uint8 1684 5764 Not applicableLoop.1.OP.FeedForwardVal Feedforward Value float32 1688 5768 0dpLoop.1.OP.FF_Rem Remote Feed Forward Input float32 168d 5773 0dpLoop.1.OP.ForcedOP Forced manual output value float32 168f 5775 1dpLoop.1.OP.ManStartup Manual Startup Mode (0 = Off; 1 = On) bool 1690 5776 Not applicableLoop.1.OP.ManualMode Manual Output Mode (0 = Track; 1 = Step; 2 = Last MOP) uint8 167f 5759 Not applicableLoop.1.OP.ManualOutVal Manual Output Value float32 1680 5760 Same as Loop.1.OP.OutputHighLimitLoop.1.OP.MeasuredPower Measured Mains Voltage float32 1682 5762 0dpLoop.1.OP.NudgeLower Valve Nudge Lower (1 = Lower) uint8 1677 5751 Not applicableLoop.1.OP.NudgeRaise Valve Nudge Raise (1 = Raise) uint8 1676 5750 Not applicablePage 199HA030554Issue 7 Nov 12