User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLoop.2.OP.FF_Rem Remote Feed Forward Input float32 178d 6029 0dpLoop.2.OP.ForcedOP Forced manual output value float32 178f 6031 1dpLoop.2.OP.ManStartup Manual Startup Mode (0 = Off; 1 = On) bool 1790 6032 Not applicableLoop.2.OP.ManualMode Manual Output Mode (0 = Track; 1 = Step; 2 = Last MOP) uint8 177f 6015 Not applicableLoop.2.OP.ManualOutVal Manual Output Value float32 1780 6016 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.MeasuredPower Measured Mains Voltage float32 1782 6018 0dpLoop.2.OP.NudgeLower Valve Nudge Lower (1 = Lower) uint8 1777 6007 Not applicableLoop.2.OP.NudgeRaise Valve Nudge Raise (1 = Raise) uint8 1776 6006 Not applicableLoop.2.OP.OutputHighLimit Output High Limit float32 176d 5997 1dpLoop.2.OP.OutputLowLimit Output Low Limit float32 176e 5998 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.PotBreakMode Potentiometer Break Mode uint8 177c 6012 Not applicable(0 = Raise; 1 = Lower; 2 = Rest; 3 = Model)Loop.2.OP.Rate Output Rate Limit Value (0 = off) float32 1770 6000 1dpLoop.2.OP.RateDisable Output Rate Limit Disable (0 = No, 1 = Yes) bool 1771 6001 Not applicableLoop.2.OP.RemOPH Remote Output High Limit float32 178c 6028 Same as Loop.2.Main.ActiveOutLoop.2.OP.RemOPL Remote Output Low Limit float32 178b 6027 Same as Loop.2.Main.ActiveOutLoop.2.OP.SafeOutVal Safe Output Value float32 177e 6014 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.SbrkOP The output power under sensor break conditions float32 178e 6030 Same as Loop.2.OP.OutputHighLimitLoop.2.OP.SensorBreakMode Sensor Break Mode (0 = SbrkOP; 1 = Hold) uint8 177d 6013 Not applicableLoop.2.OP.TrackEnable Enable Output Tracking (0 = Off; 1 = On) uint8 178a 6026 Not applicableLoop.2.OP.TrackOutVal Output Track Value float32 1789 6025 0dpLoop.2.PID.ActiveSet Current PID set uint8 1738 5944 Not applicableLoop.2.PID.Boundary1-2 Threshold for swapping between set 1 and set 2 float32 1739 5945 0dpLoop.2.PID.Boundary2-3 Threshold for swapping between set 2 and set 3 float32 173a 5946 0dpLoop.2.PID.CutbackHigh Cutback high value for PID set 1 (0 = Auto) float32 173f 5951 1dpLoop.2.PID.CutbackHigh2 Cutback high value for PID set 2 (0 = Auto) float32 1747 5959 1dpLoop.2.PID.CutbackHigh3 Cutback high value for PID set 3 (0 = Auto) float32 174f 5967 1dpLoop.2.PID.CutbackLow Cutback low value for PID set 1 (0 = Auto) float32 1740 5952 1dpLoop.2.PID.CutbackLow2 Cutback low value for PID set 2 (0 = Auto) float32 1748 5960 1dpLoop.2.PID.CutbackLow3 Cutback low value for PID set 3 (0 = Auto) float32 1750 5968 1dpLoop.2.PID.DerivativeTime Derivative time for PID set 1 float32 173d 5949 0dpLoop.2.PID.DerivativeTime2 Derivative time for PID set 2 float32 1745 5957 0dpLoop.2.PID.DerivativeTime3 Derivative time for PID set 3 float32 174d 5965 0dpLoop.2.PID.IntegralTime Integral time for PID set 1 float32 173c 5948 0dpLoop.2.PID.IntegralTime2 Integral time for PID set 2 float32 1744 5956 0dpLoop.2.PID.IntegralTime3 Integral time for PID set 3 float32 174c 5964 0dpLoop.2.PID.LoopBreakTime Loop break time for PID set 1 float32 1742 5954 0dpLoop.2.PID.LoopBreakTime2 Loop break time for PID set 2 float32 174a 5962 0dpLoop.2.PID.LoopBreakTime3 Loop break time for PID set 3 float32 1752 5970 0dpLoop.2.PID.ManualReset Manual reset value for PID set 1 float32 1741 5953 1dpLoop.2.PID.ManualReset2 Manual reset value for PID set 2 float32 1749 5961 1dpLoop.2.PID.ManualReset3 Manual reset value for PID set 3 float32 1751 5969 1dpLoop.2.PID.NumSets Number of PID sets to be used (max. 3) uint8 1736 5942 Not applicableLoop.2.PID.OutputHi Gain scheduled output high limit for PID set 1 float32 1753 5971 1dpLoop.2.PID.OutputHi2 Gain scheduled output high limit for PID set 2 float32 1755 5973 1dpLoop.2.PID.OutputHi3 Gain scheduled output high limit for PID set 3 float32 1757 5975 1dpLoop.2.PID.OutputLo Gain scheduled output low limit for PID set 1 float32 1754 5972 1dpLoop.2.PID.OutputLo2 Gain scheduled output low limit for PID set 2 float32 1756 5974 1dpLoop.2.PID.OutputLo3 Gain scheduled output low limit for PID set 3 float32 1758 5976 1dpLoop.2.PID.ProportionalBand Proportional band value for PID set 1 float32 173b 5947 1dpLoop.2.PID.ProportionalBand2 Proportional band value for PID set 2 float32 1743 5955 1dpLoop.2.PID.ProportionalBand3 Proportional band value for PID set 3 float32 174b 5963 1dpLoop.2.PID.RelCh2Gain Channel 2 relative cool gain value for PID set 1 float32 173e 5950 1dpLoop.2.PID.RelCh2Gain2 Channel 2 relative cool gain value for PID set 2 float32 1746 5958 1dpLoop.2.PID.RelCh2Gain3 Channel 2 relative cool gain value for PID set 3 float32 174e 5966 1dpLoop.2.PID.SchedulerRemoteInput Scheduler Remote Input float32 1737 5943 0dpLoop.2.PID.SchedulerType Scheduler Type uint8 1735 5941 Not applicable0 = Off 1 = Set 2 = SP 3 = PV4 = Error 5 = OP 6 = RemLoop.2.Setup.AutoManAccess Edit access to ‘Auto Man’ in Loop display page uint8 17a8 6056 Not applicable0 = Read/Write (R/W) all modes1 = Editable in all modes except ‘Logged out’2 = Editable only at Engineer and Supervisor levelsLoop.2.Setup.CH1ControlType Channel 1 Control Type uint8 1701 5889 Not applicable0 =Off; 1 = On Off; 2 = PID; 3 = VPU; 4 = VPBLoop.2.Setup.CH2ControlType Channel 2 Control Type (As channel 1, above) uint8 1702 5890 Not applicableLoop.2.Setup.ControlAction Control Action (0 = Reverse; 1 = Direct) uint8 1703 5891 Not applicableLoop.2.Setup.DerivativeType Derivative Type (0 = PV; 1 = Error) uint8 1705 5893 Not applicableLoop.2.Setup.LoopName Loop Name string_t 5d10 23824 Not applicableLoop.2.Setup.ManOutputAccess Manual output access uint8 17a9 6057 Not applicableLoop.2.Setup.LoopType Loop Type (0 = single; 1 = cascade; 2 = override; 3 = ratio) uint8 1700 5888 Not applicableLoop.2.Setup.PBUnits Proportional Band Units (0 = Engineering units; 1 = percent) uint8 1704 5892 Not applicableLoop.2.Setup.SPAccess Edit access to ‘SP’ in Loop display page uint8 17a7 6055 Not applicable0 = Read/Write (R/W) all modes1 = Editable in all modes except ‘Logged out’2 = Editable only at Engineer and Supervisor levelsLoop.2.SP.AltSP Alternative Setpoint float32 1760 5984 Same as Loop.2.Main.PVLoop.2.SP.AltSPSelect Select alternative setpoint (0 = No; 1 = Yes) uint8 1761 5985 Not applicableLoop.2.SP.ManualTrack Manual Track Enable (0 = disable; 1 = enable) uint8 1767 5991 Not applicableLoop.2.SP.RangeHigh Setpoint Range High Limit float32 1759 5977 Same as Loop.2.Main.PVLoop.2.SP.RangeLow Setpoint Range Low Limit float32 175a 5978 Same as Loop.2.Main.PVHA030554Issue 7 Nov 12Page 202
nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionLoop.2.SP.Rate Setpoint Rate Limit Value (0 = Rate limit off) float32 1762 5986 Same as Loop.2.Main.PVLoop.2.SP.RateDisable Setpoint Rate Limit Disable (0 = No; 1 = Yes) bool 1763 5987 Not applicableLoop.2.SP.RateDone Setpoint Rate Limit Complete (0 = No; 1 = Yes) bool 028a 650 Not applicableLoop.2.SP.ServoToPV Servo to PV Enable (0 = No; 1 = Yes) bool 176c 5996 Not applicableLoop.2.SP.SP1 Setpoint 1 float32 175c 5980 Same as Loop.2.Main.PVLoop.2.SP.SP2 Setpoint 2 float32 175d 5981 Same as Loop.2.Main.PVLoop.2.SP.SPHighLimit Setpoint High Limit float32 175e 5982 Same as Loop.2.Main.PVLoop.2.SP.SPIntBal SP Integral Balance (0 = Off; 1 = On) bool 176b 5995 Not applicableLoop.2.SP.SPLowLimit Setpoint Low Limit float32 175f 5983 Same as Loop.2.Main.PVLoop.2.SP.SPSelect Active Setpoint Select (0 = SP1; 1 = SP2) uint8 175b 5979 Not applicableLoop.2.SP.SPTrack Enables setpoint tracking (0 = Off; 1 = On) uint8 1768 5992 Not applicableLoop.2.SP.SPTrim Setpoint Trim float32 1764 5988 Same as Loop.2.Main.PVLoop.2.SP.SPTrimHighLimit Setpoint Trim High Limit float32 1765 5989 Same as Loop.2.Main.PVLoop.2.SP.SPTrimLowLimit Setpoint Trim Low Limit float32 1766 5990 Same as Loop.2.Main.PVLoop.2.SP.TrackPV PV for Programmer to Track float32 1769 5993 Same as Loop.2.Main.PVLoop.2.SP.TrackSP Manual Tracking Value float32 176a 5994 Same as Loop.2.Main.PVLoop.2.Tune.Alpha Alpha float32 17ad 6061 4dpLoop.2.Tune.Alpha_p Alpha_p float32 17ab 6059 2dpLoop.2.Tune.AutotuneEnable Initiate autotune (0 = Autotune Off; 1 = on) bool 1731 5937 Not applicableLoop.2.Tune.CycleNo CycleNo float32 17af 6063 0dpLoop.2.Tune.Debug Debug float32 17ae 6062 2dpLoop.2.Tune.Diagnostics Tuning diagnostics bool 31ce 12750 Not applicableLoop.2.Tune.OPss OPss float32 17ac 6060 2dpLoop.2.Tune.OutputHighLimit Autotune High Output Power Limit float32 1732 5938 Same as Loop.2.OP.OutputHighLimitLoop.2.Tune.OutputLowLimit Autotune Low Output Power Limit float32 1733 5939 Same as Loop.2.OP.OutputHighLimitLoop.2.Tune.PBs PBs float32 17b0 6064 2dpLoop.2.Tune.Settle Settle float32 17b2 6066 2dpLoop.2.Tune.Stage Stage of Tune uint8 0288 648 Not applicable0 = Reset 1 = None 2 = Monitor3 = Current SP 4 = NewSP 5 = ToSp6 = Max 7 = MinLoop.2.Tune.StageTime Time in this Stage of Tune float32 0289 649 0dpLoop.2.Tune.State Autotune state uint8 0287 647 Not applicable0 = Off 1 = Ready 2 = Complete3 = Timeout 4 = Ti Lmit 5 = R2g limitLoop.2.Tune.TDs TDs float32 17b1 6065 2dpLoop.2.Tune.TuneR2G R2G Tuning Type uint8 1608 5640 Not applicableLoop.2.Tune.Tuning Tuning float32 17aa 6058 0dpLoop.2.Tune.Type Autotune Algorithm Type uint8 1730 5936 Not applicable(0 = Cycle; 1 = Single; 2 = Adaptive; 3 = R2GPD)Math2.1.Fallback Fallback strategy uint8 2faf 12207 Not applicable0 = Clip Bad; 1 = Clip Good; 2 = Fallback Bad3 = Fallback Good; 4 = Up scale; 5 = Down scale.Math2.1.FallbackVal Fallback Value float32 2fab 12203 Same as Math2.1.OutMath2.1.HighLimit Output High Limit float32 2fac 12204 Same as Math2.1.OutMath2.1.In1 Input 1 Value float32 2fa7 12199 0dpMath2.1.In1Mul Input 1 Multiplier float32 2fa6 12198 1dpMath2.1.In2 Input 2 Value float32 2fa9 12201 0dpMath2.1.In2Mul Input 2 Multiplier float32 2fa8 12200 1dpMath2.1.LowLimit Output Low Limit float32 2fad 12205 Same as Math2.1.OutMath2.1.Oper Operation uint8 2faa 12202 Not applicable0 = Off 1 = Add 2 = Subtract3 = Multiply 4 =Divide 5 = Abs diff6 = Select Max 7 = Select Min 8 = Hot Swap9 = Sample & Hold 10 = Power 11 = Square root12 = Log 13 = Ln 14 = Exponential15 = 10 to the X 51 = SelectMath2.1.Out Output Value float32 2fae 12206 Set by Math2.1.ResolutionMath2.1.Resolution Output Resolution uint8 2fb2 12210 Not applicableMath2.1.Select Select Input 1 or Input 2 bool 2fb0 12208 Not applicableMath2.1.Status Status. 0 = Good (OK); 7 = Bad (Error) uint8 2fb1 12209 Not applicableMath2.1.Units Output Units string_t 6944 26948 Not applicableMath2.2.Fallback Fallback strategy (as Math2.1.Fallback) uint8 2fbc 12220 Not applicableMath2.2.FallbackVal Fallback Value float32 2fb8 12216 Same as Math2.2.OutMath2.2.HighLimit Output High Limit float32 2fb9 12217 Same as Math2.2.OutMath2.2.In1 Input 1 Value float32 2fb4 12212 0dpMath2.2.In1Mul Input 1 Scale float32 2fb3 12211 1dpMath2.2.In2 Input 2 Value float32 2fb6 12214 0dpMath2.2.In2Mul Input 2 Scale float32 2fb5 12213 1dpMath2.2.LowLimit Output Low Limit float32 2fba 12218 Same as Math2.2.OutMath2.2.Oper Operation (as Math2.1.Oper) uint8 2fb7 12215 Not applicableMath2.2.Out Output Value float32 2fbb 12219 Set by Math2.2.ResolutionMath2.2.Resolution Output Resolution uint8 2fbf 12223 Not applicableMath2.2.Select Select Input 1 or Input 2 bool 2fbd 12221 Not applicablePage 203HA030554Issue 7 Nov 12
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165: nanodac RECORDER/CONTROLLER: USER G
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Page 320 and 321:
Page 322 and 323:
Page 324 and 325:
Page 326 and 327:
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?