User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDE6.3.2 Wiring Editor Operating Details (Cont.)COMPOUNDSCompounds are used to simplify the top level wiring diagram, by allowing the placing of any number of functionblocks within one ‘box’, the inputs and outputs of which operate in the same way as those of a normalfunction block.Each time a compound is created, a new tab appears at the top of the wiring diagram. Initially compoundsand their tabs are named ‘Compound 1’, ‘Compound 2’, etc. but they can be renamed by right clicking eitheron the compound in the top level diagram, or anywhere within an open Compound, selecting ‘Rename’ andtyping in the required text string (16 characters max.).Compounds cannot contain other compounds (i.e. they can be created only in the top level diagram).Compound creation1. Empty compounds are created within the top level diagram by clicking on the ‘Create Compound’ toolbar icon.2. Compounds can also be created by highlighting one or more functionblocks in the top level diagram and then clicking on the ‘Create Compound’tool bar icon. The highlighted items are moved from the top leveldiagram into a new compound.CreatecompoundFlattencompound3. Compounds are ‘uncreated’ (flattened), by highlighting the relevant itemin the top level menu and then clicking on the ‘Flatten Compound’ tool bar icon. All the items previouslycontained within the compound appear on the top level diagram.4. Wiring between top level and compound parameters is carried out by clicking on the source parameter,then clicking on the compound (or the compound tab) and then clicking on the destination parameter.Wiring from a compound parameter to a top level parameter or from compound to compound iscarried out in similar manner.5. Unused function blocks can be moved into compounds by dragging from the tree view. Existing blockscan be dragged from the top level diagram, or from another compound, onto the tab associated withthe destination compound. Blocks are moved out of compounds to the top level diagram or to anothercompound in a similar way. Function blocks can also be ‘cut and pasted’.6. Default compound names (e.g. ‘Compound 2’) are used only once, so that if, for example, Compounds1 and 2 have been created, and Compound 2 is subsequently deleted, then the next compound to becreated will be named ‘Compound 3’.7. Top level elements can be click-dragged into compounds.TOOL TIPSHovering the cursor over the block displays ‘tooltips’ describing that part of the block beneath the cursor.For function block parameters the tooltip shows the parameter description, its OPC name, and, if downloaded,its value. Similar tooltips are shown when hovering over inputs, outputs and over many other items onthe iTools screen.A Function Block is enabled by dragging the block onto the diagram, wiring it, and finally downloading it tothe instrument. Initially blocks and associated wires are drawn with dashed lines, and when in this state theparameter list for the block is enabled but the block is not executed by the instrument.The block is added to the instrument function block execution list when the ‘Download’ icon is operated andthe items are redrawn using solid lines.If a block which has been downloaded is deleted, it is shown on the diagram in a ghosted form until thedownload button is pressed. (This is because it and any wires to/from it are still being executed in the instrument.On download it will be removed from the instrument execution list and the diagram.) A ghosted blockcan be ‘undeleted’ as described in ‘Context menu’, above.When a dashed block is deleted it is removed immediately.Page 270HA030554Issue 7 Nov 12
nanodac RECORDER/CONTROLLER: USER GUIDE6.4 PARAMETER EXPLORERThis view can be displayed:1. by clicking on the ‘Parameter Explorer’ toolbar icon,2. by double clicking on the relevant block in the tree pane or in the graphical wiring editor3. by selecting ‘Function Block View’ from the Function block context menu in the Graphical wiring Editor.4. by selecting ‘parameter Explorer from the ‘View’ menu5. by using the short cut +In each case the function block parameters appear in the iTools window in tabular form, such as the examplein figure 6.4a, below.Figure 6.4a Parameter table exampleThe figure above shows the default table layout. Columns can be added/deleted from the view using the‘Columns’ item of the Explorer or context menus (figure 6.4b).HA030554Issue 7 Nov 12Page 271
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233: nanodac RECORDER/CONTROLLER: USER G
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Page 340 and 341:
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

Create successful ePaper yourself

Delete template?

Save as template?