User Guide - Eurotherm Ltda

nanodac RECORDER/CONTROLLER: USER GUIDEParameter path Description Type Hex Dec ResolutionChannel.2.Alarm2.Amount Rate-of-change alarm ‘Amount’ float32 18e8 6376 Same as Channel.2.Main.PVChannel.2.Alarm2.AverageTime Rate-of-change alarm ‘Average time’ time_t 18ea 6378 Set by Network.Modbus.TimeFormatChannel.2.Alarm2.Block 0 = Blocking alarms off; 1 = Blocking alarms on uint8 18e2 6370 Not applicableChannel.2.Alarm2.ChangeTime Rate-of-change alarm ‘Change Time’ uint8 18e9 6377 Not applicableChannel.2.Alarm2.Deviation Deviation alarm ‘Deviation Value’ float32 18e7 6375 Same as Channel.2.Main.PVChannel.2.Alarm2.Dwell Alarm dwell time time_t 18e5 6373 Set by Network.Modbus.TimeFormatChannel.2.Alarm2.Hysteresis Alarm hysteresis value float32 18e4 6372 Same as Channel.2.Main.PVChannel.2.Alarm2.Inactive 1 = alarm source safe and ack’d (if necessary) bool 18ee 6382 Not applicableChannel.2.Alarm2.Inhibit 1 = Alarm inhibited bool 18f1 6385 Not applicableChannel.2.Alarm2.Latch Alarm latch type (as for Channel.1.Alarm1) uint8 18e1 6369 Not applicableChannel.2.Alarm2.NotAcknowledged 1 = alarm has not been acknowledged bool 18ef 6383 Not applicableChannel.2.Alarm2.Reference Deviation alarm ‘Reference’ value float32 18e6 6374 Same as Channel.2.Main.PVChannel.2.Alarm2.Status Alarm status (as for Channel.1.Alarm1) uint8 0107 263 Not applicableChannel.2.Alarm2.Threshold Alarm trigger threshold float32 18e3 6371 Same as Channel.2.Main.PVChannel.2.Alarm2.Type Alarm type (as for Channel.1.Alarm1) uint8 18e0 6368 Not applicableChannel.2.Main.CJType Cold junction compensation type (as for Channel.1.Main) uint8 188c 6284 Not applicableChannel.2.Main.CloseString Close String string_t 4999 18841 Not applicableChannel.2.Main.Descriptor Text string to describe the channel string_t 491b 18715 Not applicableChannel.2.Main.ExtCJTemp External CJ temperature float32 188d 6285 1dpChannel.2.Main.FaultResponse Input fault response uint8 1890 6288 Not applicableChannel.2.Main.Filter Filter time constant float32 188e 6286 1dpChannel.2.Main.InputHigh Input range high value float32 1884 6276 1dpChannel.2.Main.InputLow Input range low value float32 1883 6275 1dpChannel.2.Main.InternalCJTemp Channel 2 internal cold junction temperature float32 1895 6293 1dpChannel.2.Main.IPAdjustState Input Adjust state (0 = Unadjusted; 1 =Adjusted) bool 1896 6294 Not applicableChannel.2.Main.IPAdjustState2 Secondary Input Adjust state (0 = Unadjusted; 1 = Adjusted) bool 189c 6300 Not applicableChannel.2.Main.LinType Linearisation type (as for Channel.1.Main) uint8 1886 6278 Not applicableChannel.2.Main.MeasuredValue Input value before linearisation, scaling, adjust etc. float32 1894 6292 Set by Channel.2.Main.ResolutionChannel.2.Main.MeasuredValue2 Measured value of the secondary input float32 1899 6297 Set by Channel.2.Main.ResolutionChannel.2.Main.Offset Fixed value to be added to/subtracted from PV float32 1897 6295 3dpChannel.2.Main.Offset2 Secondary input offset float32 1898 6296 3dpChannel.2.Main.OpenString Open String string_t 4975 18805 Not applicableChannel.2.Main.PV The output (displayed) value of the channel. float32 0104 260 Set by Channel.2.Main.ResolutionChannel.2.Main.PV2 The secondary input process variable (output) of the channel float32 0114 276 Set by Channel.2.Main.ResolutionChannel.2.Main.RangeHigh Range high value float32 1888 6280 Set by Channel.2.Main.ResolutionChannel.2.Main.RangeLow Range low value float32 1887 6279 Set by Channel.2.Main.ResolutionChannel.2.Main.RangeUnits Range units (as channel.1.Main) uint8 1889 6281 Not applicableChannel.2.Main.Resolution Specifies the resolution/number of decimal places uint8 1881 6273 Not applicableChannel.2.Main.ScaleHigh Scale high value float32 188b 6283 Set by Channel.2.Main.ResolutionChannel.2.Main.ScaleHigh2 Scale high value for the secondary input float32 189b 6299 Set by Channel.2.Main.ResolutionChannel.2.Main.ScaleLow Scale low value float32 188a 6282 Set by Channel.2.Main.ResolutionChannel.2.Main.ScaleLow2 Scale low value for the secondary input float32 189a 6298 Set by Channel.2.Main.ResolutionChannel.2.Main.SensorBreakType Sensor break type (as for Channel.1.Main) uint8 188f 6287 Not applicableChannel.2.Main.SensorBreakVal Sensor break value uint8 1891 6289 Not applicableChannel.2.Main.Shunt Shunt value in Ohms float32 1885 6277 2dpChannel.2.Main.Status Channel status (as for Channel.1.Main.Status) uint8 0105 261 Not applicableChannel.2.Main.Status2 The secondary input PV (output) status (as above) uint8 0115 277 Not applicableChannel.2.Main.TestSignal Channel test waveform (as for Channel.1.Main) uint8 1882 6274 Not applicableChannel.2.Main.Type Channel function (as for Channel.1.Main.Type) uint8 1880 6272 Not applicableChannel.2.Main.Units Channel units string string_t 4930 18736 Not applicableChannel.2.Trend.Colour Trend colour (as for Channel.1.Trend.Colour) uint8 18a0 6304 Not applicableChannel.2.Trend.SpanHigh Specifies the highest PV (output value) to be displayed float32 18a2 6306 Same as Channel.2.Main.PVChannel.2.Trend.SpanLow Specifies the lowest PV (output value) to be displayed float32 18a1 6305 Same as Channel.2.Main.PVChannel.3.Alarm1.Acknowledgement 1 = alarm acknowledged bool 1950 6480 Not applicableChannel.3.Alarm1.Active 1 = alarm source active, or safe but not ack’d bool 194b 6475 Not applicableChannel.3.Alarm1.Amount Rate-of-change alarm ‘Amount’ float32 1948 6472 Same as Channel.3.Main.PVChannel.3.Alarm1.AverageTime Rate-of-change alarm ‘Average time’ time_t 194a 6474 Set by Network.Modbus.TimeFormatChannel.3.Alarm1.Block 0 = Blocking alarms off; 1 = Blocking alarms on. uint8 1942 6466 Not applicableChannel.3.Alarm1.ChangeTime Rate-of-change alarm ‘Change Time’ uint8 1949 6473 Not applicableChannel.3.Alarm1.Deviation Deviation alarm ‘Deviation Value’ float32 1947 6471 Same as Channel.3.Main.PVChannel.3.Alarm1.Dwell Alarm dwell time time_t 1945 6469 Set by Network.Modbus.TimeFormatChannel.3.Alarm1.Hysteresis Alarm hysteresis value float32 1944 6468 Same as Channel.3.Main.PVChannel.3.Alarm1.Inactive 1 = alarm source safe and ack’d (if necessary) bool 194e 6478 Not applicableChannel.3.Alarm1.Inhibit 1 = alarm inhibited bool 1951 6481 Not applicableChannel.3.Alarm1.Latch Alarm latch type (as for Channel.1.Alarm1) uint8 1941 6465 Not applicableChannel.3.Alarm1.NotAcknowledged 1 = alarm has not been acknowledged bool 194f 6479 Not applicableChannel.3.Alarm1.Reference Deviation alarm ‘Reference’ value float32 1946 6470 Same as Channel.3.Main.PVChannel.3.Alarm1.Status Alarm status (as for Channel.1.Alarm1) uint8 010a 266 Not applicableChannel.3.Alarm1.Threshold Alarm trigger threshold float32 1943 6467 Same as Channel.3.Main.PVChannel.3.Alarm1.Type Alarm type (as for Channel.1.Alarm1) uint8 1940 6464 Not applicableChannel.3.Alarm2.Acknowledge 1 = acknowledge alarm bool 01b5 437 Not applicableChannel.3.Alarm2.Acknowledgement 1 = alarm acknowledged bool 1970 6512 Not applicableChannel.3.Alarm2.Active 1 = alarm source active, or safe but not ack’d bool 196b 6507 Not applicableChannel.3.Alarm2.Amount Rate-of-change alarm ‘Amount’ float32 1968 6504 Same as Channel.3.Main.PVChannel.3.Alarm2.AverageTime Rate-of-change alarm ‘Average time’ time_t 196a 6506 Set by Network.Modbus.TimeFormatChannel.3.Alarm2.Block 0 = Blocking alarms off; 1 = Blocking alarms on. uint8 1962 6498 Not applicableChannel.3.Alarm2.ChangeTime Rate-of-change alarm ‘Change Time’ uint8 1969 6505 Not applicableChannel.3.Alarm2.Deviation Deviation alarm ‘Deviation Value’ float32 1967 6503 Same as Channel.3.Main.PVChannel.3.Alarm2.Dwell Alarm dwell time time_t 1965 6501 Set by Network.Modbus.TimeFormatChannel.3.Alarm2.Hysteresis Alarm hysteresis value float32 1964 6500 Same as Channel.3.Main.PVHA030554Issue 7 Nov 12Page 184