User Guide - Eurotherm Ltda

More documents

Recommendations

Info

nanodac RECORDER/CONTROLLER: USER GUIDE6.6.5 Loading and Saving programsThe four program operation keys at the top left of the programmer window allow the user to load a programfrom or save a program to either the currently connected instrument or to a pc.The fourth icon allows the user to select a program to be deleted from the connected instrument.See section 6.6.6 for more details.6.6.6 Toolbar iconsThe toolbar icons appearing at the top of the programmer window have the following properties:Load Program. Opens a browser window allowing the user to select a program on the pc, or a programstored in the connected instrument to load. Short cut: + .Save current program to file. Opens a browser window allowing the user to select a location on the pcin which to save the current program. This file is saved with a ‘.upiz’ extension and can be saved to a USBmemory stick for downloading to an instrument, or it can be transferred to the instrument via an ftp server.Short cut: + .Store current program on device. Allows the user to save the program to the program store on the instrument.Short cut: + + .Delete Programs from Device. Allows the user to delete programs from the program store on the connectedinstrument. Short cut: + .Cut. Removes the highlighted segment(s) from the program and places them on the pasteboard. Shortcut: + .Copy. Copies the selected segment(s) to the pasteboard, leaving the original segments in place. Shortcut: + .Paste insert. Inserts the segments on the pasteboard into a location to the left of the highlighted segment.Short cut: + .Paste over. Overwrites the highlighted segment(s) with the segment(s) on the pasteboard. The numberof segments on the pasteboard must match the number of segments being overwritten. Short cut: + + .Insert. Inserts a new segment to the left of the highlighted segment. If more than one segment is highlighted,then the same number of segments are inserted as are highlighted. Copies the segment type ofthe segment to the right of the insertion point except if that segment is an ‘End’ or ‘GoBack’ segment,when newly inserted segments are of type ‘Ramp’. Short cut: .Delete. Deletes the highlighted segment(s). Short cut: + .Go to first. Moves the user to the first segment. Useful in very long programs. Short cut: +.Go to last. Moves the user to the end segment. Useful in very long programs. Short cut: +.Analog. Selects the analogue trace chart for display and segment configuration. Short cut: +.Digital Event Outputs. Selects the Event output chart for display and configuration.Short cut: +.Logarithmic. Switches the vertical scale to logarithmic. Short cut: + (figure 6.6.6)Page 280HA030554Issue 7 Nov 12
nanodac RECORDER/CONTROLLER: USER GUIDE6.6.6 Toolbar Icons (Cont.)Figure 6.6.6 Logarithmic scale example6.6.7 Context menusSEGMENT CONTEXT MENURight-clicking when the mouse cursor is hovering over a segment in the analoguesegment parameters view produces the segment context menushown. The various items copy the relevant tool bar icons described above,with the following additions:Select AllSelects all parametersParameter properties Displays the properties window for the parameterright-clicked on, including a ‘Help’ tag for that parameter.PROGRAM CONTEXT MENURight-clicking when the mouse cursor is hovering in the program parametersview produces the program context menu shown.Parameter properties Displays the properties window for the parameterright-clicked on, including a ‘Help’ tag for that parameter.ColumnsAllows the user to enable/disable columns in the program parameters display.CHART CONTEXT MENURight-clicking when the mouse cursor is hovering over the analogue chart or the digitalevent chart produces the segment context menu shown. This allows the user to copythe chart to the pasteboard, from where it can be pasted into (for example) a standardword procesing document.HA030554Issue 7 Nov 12Page 281
Page 1 and 2:
nanodacUser Guidenanodac recorder/c
Page 3:
Declaration of ConformityManufactur
Page 6 and 7:
nanodac RECORDER/CONTROLLER: USER G
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243: nanodac RECORDER/CONTROLLER: USER G
Page 342 and 343:
Page 344 and 345:
Page 346 and 347:
Page 348 and 349:
NANODAC RECORDER/CONTROLLER: USER G
Page 350 and 351:
Page 352 and 353:
Page 354 and 355:
Page 356 and 357:
Page 358 and 359:
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
Page 366 and 367:
Page 368 and 369:
Page 370 and 371:
Page 372 and 373:
Page 374 and 375:
Page 376 and 377:
Page 378 and 379:
Page 380 and 381:
Page 382 and 383:
Page 384 and 385:
Page 386 and 387:
Page 388 and 389:
Page 390 and 391:
Page 392:
show all

User Guide - Eurotherm Ltda

Create successful ePaper yourself

Delete template?

Save as template?